Diving Accessories XS Scuba

Attach one end to a first stage low pressure port.The other end allows the attachment of a industrial style hose with 1/4 NPT female threads.3/8-24 male to 1/4 male NPT.Brass construction with black chrome finish.Low pressure only - below 200 psi.

Features:- Included with Mini Tech Gauge Kit- Use to mount a Mini Tech Gauge to HP hose- Inline (180º) with the HP hose- Airspool with Viton o-rings included

Same design as Single Weight Pocket above, except:- Allows pocket to be quickly added without having to slide over the end of webbing.- Quick attachment with double Velcro® closure at bottom of pocket.Designed to add up to 5 pounds of shot or hard weight.Easy addition to XS Scuba ponypac or other harness systems.Perfect for adjusting your trim.

Rear Tail Ballast Pocket 2,7 kg.The XS Scuba Tail weight bag (2.7 kg) is designed to screw onto the lower end of the backplate to optimise the diver´s fit.Weight: holds up to 2.7 kg.

Elbow Adapter 90 second Stage.

Connector that directly fits the 1st stage outlet ports. This enables you to connect a LP hose in an ideal way that would not be possible without this rotatable adapter!

LP Hose Splitter AC918 - Attach to the second stage end of one low pressure regulator hose - Allows the attachment of two low pressure regulator hoses (first stage ends) - One 9/16-18 male inlet to two 3/8-24 female outlets - Chromed brass construction - Low pressure only - below 200 psi

Elbow Adapter 70 second Stage.

Add trim weight in the center groove of your backplateAttach with twin cylinder band bolts11inch/28cm center to centerSealed opening with double VelcroJust pour in your lead shot of up to 5 lbs./2,2kg

Features:- Velcro release weight dump - pull out, then down- Designed to add up to 5 lbs. of bagged shot or hard weight - Attaches by sliding over the end of any 2 webbing - Easy addition to XS Scuba weight belt or other harness systems- Perfect for adjusting your trim

Precision machined from 316L stainless steel.Protects 200 and 300 bar DIN threads.Seals water out with Viton o-ring for oxygen compatibility.No groove through threads.

Male quick-disconnect only of AC990, Allows attachment of multiple second stages to a single hose, Chromed brass construction, Low pressure only - below 200 psi, Factory cleaned - Viton o-ring.,.

This brassed adapter with an 90° angel fits between HP hose and 1st stage. The whole adapter is rotating, so it´s good for strait hose configuration, eg with rebreathers.

ADAPTER 90 DEGREE 1ST STAGE LP SWIVEL 3-8.Adapter 90 degree for LP port of 1 stage, with swivel, UNF 3-8, chromed brass.

Features: - Converting your regulator/hoses to 1/4 NPT has many practical application in diving as well as your garage or shop- Used with surface supplied umbilicals, switch blocks, comm gear and pneumatic tools- Viton o-rings where applicable- 1/4 NPT male to 9/16-18 male- Stainless steel construction

Features:- Converting your regulator/hoses to 1/4 NPT has many practical application in diving as well as your garage or shop- Used with surface supplied umbilicals, switch blocks, comm gear and pneumatic tools- Viton o-rings where applicable- 1/4 NPT male to 3/8-24 UNF female- Stainless steel construction

Features:Convert any standard regulator hose to a BC quick disconnect hoseInstalls on the second stage end of a regulator hoseSix point attachment with six ball-bearings´EZ´ QD design, just push to attach - no need to pull back the collarWide easy grip collarA favorite for drysuit inflation hosesChromed brass constructionLow pressure use only - below 200 psiFactory cleaned - Viton o-rings

Features:Install between standard regulator hose and second stage9/16-18 UNF male inlet to 9/16-18 UNF female outlet threadsSlide machined Delrin collar to shut off gas flowPrevent critical gas lossCommonly used with deco rigs, stage bottles & drysuit inflationLow pressure use only - below 200 psi

Features: - Make any primary regulator more comfortable while diving - Routes the hose under the right arm instead of over the shoulder - Often used on octopus to improve hose routing - Installs between the second stage and the regulator hose - Chromed brass construction - Low pressure use only - below 200 psi - Factory cleaned - Viton o-rings

Make any primary regulator more comfortable while diving.Routes the hose under the right arm instead of over the shoulder.Often used on octopus to improve hose routing.Installs between the second stage and the regulator hose.Chromed brass construction.Usable up to 40% oxygen.Choose the pefect angle between 0° and 350° by simply twisting the adapter!.

Make any primary regulator more comfortable while diving.Routes the hose under the right arm instead of over the shoulder.Often used on octopus to improve hose routing.Installs between the second stage and the regulator hose.Chromed brass construction.Low pressure use only - below 200 psi.Factory cleaned - Viton o-rings.

Features: - Install between first stage medium pressure port and standard regulator hose.- Slide machined Delrin collar to shut off gas flow.- Commonly used with rebreather systems.Specifications: - 3/8-24 UNF male inlet to 3/8-24 UNF female outlet threads.- Low pressure use only - below 200 psi.

Regulators - Accessories.XS SCUBA Carabiner Adapter 2nd Stage 1/3 Ports.Carabiner adapter second stage 1/3 ports.

Features: - Use this to route your HP hose 90º- Chromed brass construction with Viton o-rings- High pressure only – maximum 5000 psi- Cleaned for use with up to 40% pre-blended Nitrox- (1) 7/16-20 male inlet to (1) 7/16-20 female outlet