Cooling Systems Accessories EKWB

EK-Cable Pump testing adapter is a simple adapter cable for connecting any liquid cooling pump (with 4-pin fan header) or computer cooling fan with SATA power cable. This adapter is recommended to be used only for testing purposes while leak-testing your loop and is intended to be connected directly to PSU, without the need for powering up the entire system. The cable is approximately 15cm long.Features: - 3-pin fan header to SATA power adapter- RoHS compliant

Replacement inner O-ring gaskets for EK Hard Tube Compression (HDC) 14mm OD fittings.The package contains 6 pieces of OR 14,1x1,6 NBR70.These O-ring gaskets are compatible with the following fitting lines:EK-Quantum Torque HDC 14EK-Classic HDC 14

Replacement inner O-ring gaskets for EK Hard Tube Compression (HDC) 16mm OD fittings.The package contains 6 pieces of OR 16,1x1,6 NBR70.These O-ring gaskets are compatible with the following fitting lines:EK-Quantum Torque HDC 16EK-Classic HDC 16

A set of twenty (20) spare 6mm long screws for EK-Quantum Surface S, P, and X series radiators.Recommended for mounting the EK-Quantum Surface radiators directly to the case or through an open frame fan.Specifications:- Thread: M4- Screw length: 6mm- Head type: Phillips

EK-Quantum Torque Micro HDP 12 fittings are EK's new push-in hard-tube fittings designed for use with 12mm solid tubing such as Acrylic and PETG. They are stealthy and made to be as small as possible, and with NO added branding at all. They are engineered specifically for captive tubing - like runs between two GPU water blocks, or from a GPU to the distro plate. Most importantly, the tube should not be able to move when using these fittings. The solid tube is gripped by the high-quality EPDM rubber gasket inside the Torque Micro HDP fitting. The fitting is made of CNC-machined brass with satin-black finish. Black Quantum Torque series fittings are intentionally not painted on the inside to …

Replacement outer O-ring gaskets for EK fittings and angled adapters.Package contains 6 pieces of OR 12x2.These fittings are compatible with following fitting lines: EK-HDC 16mm EK-ACF 10/13mm EK-ACF 10/16mm EK-ACF 13/19mm EK-ACF 12/16mm EK-HD Adapter 12/16mm EK-Coolstream extenders EK-ACF 10/16mm

EK-Quantum Torque Micro HDP 12 fittings are EK's new push-in hard-tube fittings designed for use with 12mm solid tubing such as Acrylic and PETG. They are stealthy and made to be as small as possible, and with NO added branding at all. They are engineered specifically for captive tubing - like runs between two GPU water blocks, or from a GPU to the distro plate. Most importantly, the tube should not be able to move when using these fittings. The solid tube is gripped by the high-quality EPDM rubber gasket inside the Torque Micro HDP fitting. The fitting is made of nickel-plated CNC-machined brass. These fittings are guaranteed to be compatible with all other EK Water Blocks liquid cooling …

The EK-HD PETG Inserts are EK's way of battling against potential hazards that the use of PETG tubes present. PETG tubes are extremely popular because of the ease of use and their flexibility. On the other hand, PETG tubing, especially the thin tube wall models (10/12) are prone to deformation when exposed to high temperatures (40°C and above). The deformation rate depends on the duration and maximum temperature reached. These temperatures can be reached with pump failures, water block clogging, etc. The EK-HD PETG Inserts provide a safety measure for 12mm OD / 10mm ID PETG tubes which prevents the tube wall from collapsing inside the compression fitting. The EK-HD PETG Insert is low …

The EK-HD PETG Inserts are EK's way of battling against potential hazards that the use of PETG tubes present. PETG tubes are extremely popular because of the ease of use and their flexibility. On the other hand, PETG tubing is prone to deformation when exposed to high temperatures (40°C and above). The deformation rate depends on the duration and maximum temperature reached. These temperatures can be reached with pump failures, water block clogging, etc. The EK-HD PETG Inserts provide a safety measure for 16mm OD / 12mm ID PETG tubes which prevents the tube wall from collapsing inside the compression fitting. The EK-HD PETG Insert is low profile and it is not visible when in use with …

Spare Reservoir Holder made from POM Acetal for cylindrical reservoirs 60mm in diameter.Grip can be adjusted by side-positioned screw.May be used on EK-Multioption RES X2 and EK-RES X3 reservoirs as well as 3rd party product.Contents:- Holder (2x)- Mounting mechanism

EK-Loop Bending Cord for 10mm ID Hard Tube - 0.33m is a silicone cord for bending acrylic and PETG tubing. It features high heat and abrasion resistance, helping the tube not to deform while subjected to the high temperatures of a heat gun during the bending process. Using a heat gun and the enclosed silicone bending cord (insert), it is possible to make customized pieces of solid tubing. Use the hacksaw to cut pieces to length and sandpaper to chamfer and smooth out the edges. For a perfect chamfer, EK recommends the use of the EK-HD Tube Reamer tool. EK-Loop Bending Cord is 0.33m long. It is made of flexible silicone with high elasticity, allowing it to be inserted and pulled out of a bent …

EK-Quantum Torque Micro HDP 12 fittings are EK's new push-in hard-tube fittings designed for use with 12mm solid tubing such as Acrylic and PETG. They are stealthy and made to be as small as possible, and with NO added branding at all. They are engineered specifically for captive tubing - like runs between two GPU water blocks, or from a GPU to the distro plate. Most importantly, the tube should not be able to move when using these fittings. The solid tube is gripped by the high-quality EPDM rubber gasket inside the Torque Micro HDP fitting. The fitting is made of CNC-machined brass with high-quality satin silver finish. Satin Titanium Quantum Torque series fittings are intentionally not painted …

The EK-RES X3 TOP WHITE is an replacement white top end cap for EK-RES X3 series reservoirs and other RES X3 based parts.EK-RES X3 TOP WHITE is made of quality machined POM Acetal material.Contents:- EK-RES X3 TOP WHITE- including sealing gasket (o-ring / OR 52x2.5)Compatibility:This spare part is compatible with the following EK reservoirs:- EK-RES X3 110- EK-RES X3 150- EK-RES X3 250- EK-RES X3 400- EK-DDC X-RES CSQ- EK-D5 X-RES CSQPlease note:- G 1/4 plug to close the port is no enclosed.- Allen key 6mm, required for tightening of G1/4 plugs, is not enclosed. It is however being enclosed within each delivery of the EK-RES X3 series reservoirs.Made in Slovenia - EU!

EK-Quantum Torque Micro HDC 12 - Black is a premium 12mm fitting made for solid tubing, such as acrylic, PETG, and brass. A much smaller footprint will allow tube placement in places where a regular fitting would be too large or inconvenient. It was named Micro due to an installed height of only 11.5mm, which is 23% shorter than standard Torque HDC 12 fittings. The outer diameter of the fitting is also significantly smaller than its bigger brother, with only 16mm across the fitting. The solid tube is gripped by the high-quality EPDM rubber gasket inside the Torque Micro compression ring. The fitting is made of CNC-machined brass with a satin black finish. The surface of the fitting is smooth …

EK-Loop Connect Level Sensor TBE 60 is a coolant level sensor provides a warning when the reservoir reaches a point where it would be prudent to top it off. Due to the coolant evaporation through the tubing, it makes sure the pump never runs dry. Also, in case of a leak, it warns you of the coolant level being below its optimal value.It attaches to the tube of the EK tubular-style reservoirs with 60mm diameter and connects via a dedicated cable to the EK-Loop Connect control unit.Technical Specifications:- Connectors: 4-pin- Length: 50cm

EK-Quantum Torque HDC 14 fittings are EK's new minimalistic 14mm hard-tube compression fittings designed for use with solid tubing such as Acrylic and PETG. With a non-intrusive, yet striking look, and with NO added branding at all. They can be complemented by interchangeable aesthetic color rings, and are an ideal choice for anyone and a perfect match with EK-Quantum series products.EK-Quantum Torque series products received the prestigious iF Design Award. A robust and industrial aesthetic sets the Torque family apart by highlighting the precise manufacturing processes used to create them. In addition, enthusiasts can add a unique color ring to give a personal accent to the fitting line. The …

EK-Quantum Torque HDC 12 fittings are EK's new minimalistic 12mm hard-tube compression fittings designed for use with solid tubing such as Acrylic and PETG. With a non-intrusive, yet striking look, and with NO added branding at all. They can be complemented by interchangeable aesthetic color rings, and are an ideal choice for anyone and a perfect match with EK-Quantum series products.EK-Quantum Torque series products received the prestigious iF Design Award. A robust and industrial aesthetic sets the Torque family apart by highlighting the precise manufacturing processes used to create them. In addition, enthusiasts can add a unique color ring to give a personal accent to the fitting line. The …

EK-Quantum Torque HDC 12 fittings are EK's new minimalistic 12mm hard-tube compression fittings designed for use with solid tubing such as Acrylic and PETG. With a non-intrusive, yet striking look, and with NO added branding at all. They can be complemented by interchangeable aesthetic color rings, and are an ideal choice for anyone and a perfect match with EK-Quantum series products. The locking ring prevents solid tube to be pulled out of the fitting by compressing the rubber gasket underneath the ring. The grooves on the outside allow for easier hand tightening. The compression ring has cutouts in EK Quantum signature shape allowing for the colored aesthetic ring to be shown. The colored …

EK-Quantum Torque HDC 14 fittings are EK's new minimalistic 14mm hard-tube compression fittings designed for use with solid tubing such as Acrylic and PETG. With a non-intrusive, yet striking look, and with NO added branding at all. They can be complemented by interchangeable aesthetic color rings, and are an ideal choice for anyone and a perfect match with EK-Quantum series products.EK-Quantum Torque series products received the prestigious iF Design Award. A robust and industrial aesthetic sets the Torque family apart by highlighting the precise manufacturing processes used to create them. In addition, enthusiasts can add a unique color ring to give a personal accent to the fitting line. The …

EK-Quantum Torque HDC 12 fittings are EK's new minimalistic 12mm hard-tube compression fittings designed for use with solid tubing such as Acrylic and PETG. With a non-intrusive, yet striking look, and with NO added branding at all. They can be complemented by interchangeable aesthetic color rings, and are an ideal choice for anyone and a perfect match with EK-Quantum series products.EK-Quantum Torque series products received the prestigious iF Design Award. A robust and industrial aesthetic sets the Torque family apart by highlighting the precise manufacturing processes used to create them. In addition, enthusiasts can add a unique color ring to give a personal accent to the fitting line. The …

EK-Quantum Torque Micro HDC 12 - Black is a premium 12mm fitting made for solid tubing, such as acrylic, PETG, and brass. A much smaller footprint will allow tube placement in places where a regular fitting would be too large or inconvenient. It was named Micro due to an installed height of only 11.5mm, which is 23% shorter than standard Torque HDC 12 fittings. The outer diameter of the fitting is also significantly smaller than its bigger brother, with only 16mm across the fitting. The solid tube is gripped by the high-quality EPDM rubber gasket inside the Torque Micro compression ring. The fitting is made of CNC-machined brass with a satin black finish. The surface of the fitting is smooth …

EK-Loop Hard Tube is a solid type of extruded acrylic tubing intended for use with EK-HD push-in adapters and EK-HDC series compression fittings. The tubing may be heat treated to achieve certain bends. For expert users only!It is mandatory to chamfer the edges of the freshly cut tube in order to prevent gasket (O-ring) damage. EK recommends a 0,5mm x 45° chamfer.Technical data:- Material: Extruded acrylic- Inner diameter: 10 mm- Outer diameter: 14 mm- Length: 2x 500 mm (19.5")The package contains 2 pieces of the tube only. Please purchase EK-HD Adapter or EK-HDC compression fittings separately!