Comparison Acer Aspire 3 A315-59G [A315-59G-50VK] vs Acer Aspire 5 A515-57G [A515-57G-54V1]

The result shown by the laptop processor in the Passmark CPU Mark test.

Passmark CPU Mark is a comprehensive test that is more detailed and reliable than the popular 3DMark06 (see above). It checks not only the gaming capabilities of the CPU, but also its performance in other modes, based on which it displays the overall score; this score can be used to fairly reliably evaluate the processor as a whole (the more points, the higher the performance).

The type of drive that is installed in the laptop.

Classic hard drives (HDD) in modern laptops are quite rare in their pure form. Instead, solid-state SSD modules are becoming more common, including in HDD+SSD and SSHD+SSD combinations. Also note that among such modules, M.2 SSDs are very common, which can also support NVMe and/or belong to the advanced Intel Optane series. Here are the main features of these options in various combinations (as well as other drive options that can be found in modern laptops):

— HDD. Traditional hard disk, not complemented by any other type of storage. HDDs are notable for their low cost per gigabyte of capacity, which allows you to create very capacious and at the same time quite inexpensive media. On the other hand, such storages are considered less perfect than SSDs: in particular, they are rather slow, and they also do not withstand shocks and shocks (the latter is especially true in light of the fact that laptops are originally portable devices). Therefore, this option is quite rare nowadays, mainly among low-cost configurations.

— SSD. Solid-state memory based on flash technology. In general, drives of this type are noticeably more expensive than HDDs of a similar volume, but they have a number of advan...tages over them — first of all, this is a high speed of operation, as well as the ability to endure quite strong shocks and vibrations without any problems. However, we emphasize that in this case we are talking about SSDs of the original format that do not use the M.2 interface, do not belong to the Optane series and are not eMMC or UFS modules (see below for all these features). This is the simplest and most affordable type of flash memory — in particular, it usually uses a SATA interface connection, which does not allow you to realize the full potential of such memory. On the other hand, even “regular” SSD modules still work noticeably faster than HDDs, and they are noticeably cheaper than more advanced solutions.

— SSD M.2. SSD module using M.2 connector. For SSDs in general, see above; and the M.2 connector was specifically designed for advanced yet tiny internal components, including solid state drives. One of the features of such a connection is that it is most often carried out according to the PCI-E standard — this provides a high data transfer rate (up to 8 GB / s, potentially more) and allows you to use all the features of SSD drives. At the same time, there are M.2 modules that work on the older SATA interface — its speed does not exceed 600 MB / s, but such equipment is cheaper than modules with M.2 PCI-E. For details, see "M.2 drive interface" — it is this item that allows you to evaluate the specific capabilities of SSD M.2.

— SSD M.2 Optane. An M.2 SSD (see above) belonging to the Intel Optane series. The main feature of such modules is the use of 3D Xpoint technology — it differs significantly from NAND, on which most conventional SSD modules are built. In particular, 3D Xpoint allows you to access data at the level of individual cells and do without some additional operations, which speeds up work and reduces delays. In addition, such memory is much more durable. Its main drawback is a somewhat high cost. It is also worth noting that the superiority of Optane over more traditional SSD modules is most noticeable at the so-called low queue depth — that is, with a small load on the drive, when a small number of requests are received at the same time. However, most everyday tasks (working with documents, surfing the web, relatively undemanding games) are implemented in this mode, so this moment can be considered an advantage — especially since the superiority of Optane, although it decreases, does not disappear with increasing load.

— HDD+SSD. The presence in the laptop of two separate drives — HDD and a regular SSD (not M.2, not Optane). The advantages and disadvantages of these types of drives are described in detail above; and their combination in one system allows you to combine the advantages and partially compensate for the shortcomings. SSD in such cases usually has a noticeably smaller volume than HDD, and is used to store data for which high access speed is critical: the operating system, work programs, etc. In turn, it is convenient to store information on a hard disk that takes up a significant volume and at the same time does not require a special access speed; a classic example is multimedia files and documents. In addition, the solid state module can be used as a high-speed cache for a hard drive — similar to the SSHD described below. However, this usually requires special software settings, while the "two separate drives" mode is usually available by default.
It is also worth noting that modern laptops are increasingly using HDD bundles not with conventional SSDs, but with more advanced M.2 modules (including M.2 Optane). However, this option also continues to be used — mainly among relatively inexpensive configurations.

— SSHD. A combination drive that combines a hard disk drive (HDD) and a solid state drive (SSD). It differs from the HDD + SSD bundle described above in two ways. Firstly, both carriers are in the same case and are perceived by the system as a single unit. Secondly, the hard drive is mainly used directly for data storage, and SSD memory usually performs an auxiliary function — it works as a high-speed cache for the HDD. In fact, it looks like this: the data from the hard drive, which the user most often accesses, is copied to the SSD and, at the next access, is loaded from the solid state media, and not from the HDD. This allows you to significantly speed up the work compared to conventional hard drives. However in terms of speed, such “hybrids” are still inferior even to conventional SSDs, not to mention M.2 and Optane solutions — but they are much cheaper.

— HDD+SSD M.2. Combination of a classic hard drive with an M.2 solid-state SSD module. For more information about this combination, see "HDD + SSD": almost everything stated there is also relevant for this case, adjusted for the fact that M.2 SSDs are able to provide higher speeds (see also above — in p. " SSD M.2").

— HDD + Optane M.2. Combining a classic hard drive with an Intel Optane M.2 solid-state SSD module. This combination is generally similar to the “HDD + SSD” combination (see above), adjusted for the advanced capabilities of Optane drives (see also “SSD M.2 Optane” above).

— SSHD+SSD M.2. Combining an SSHD with an M.2 SSD. In general, it is similar to the “HDD + SSD M.2” combination (see above), adjusted for the fact that instead of a regular hard drive, a more advanced and high-speed hybrid drive is used (see also above about it). This further increases the cost, but improves performance.

— eMMC. A type of solid-state drive, originally used as built-in permanent memory for smartphones and tablets, but has recently been installed in laptops. It differs from SSD (see above), on the one hand, by lower cost and good energy efficiency, on the other hand, by lower speed and reliability. Thus, eMMC is now found mainly among transformers and laptop-tablets (see "Type") — for them, low power consumption is more important than maximum performance. Also note that such drives are usually made built-in and do not require replacement.

— HDD + eMMC. Combining a classic hard drive with an eMMC solid state module. The features of each type of drive are described in detail above, and their combination is used mainly in laptop-tablet devices (see "Type"). At the same time, the eMMC drive is installed at the top of the device and is designed to store the operating system and the most important data that needs constant access; and the HDD, located in the lower half, is used as additional storage for large amounts of information (for example, movie collections).

— SSD M.2 + eMMC. The combination of two solid-state modules in one laptop — SSD M.2 and eMMC. See above for details on the features of both types of memory, and their combination is a rather exotic option. It is mainly used to increase the total amount of solid-state memory without a significant increase in cost (remember, eMMC is cheaper than an M.2 SSD of the same volume). In addition, while the eMMC module is usually made built-in, the M.2 SSD is removable by definition, and can be replaced with another drive if necessary.

— UFS. Another type of solid-state memory, originally designed for smartphones and tablets — along with the eMMC described above. It differs from the latter both in high efficiency and increased cost. Thus, such drives are extremely rare among laptops: where eMMC capabilities are not enough, manufacturers usually use full-fledged SSDs.

The capacity of the drive installed in the laptop. If there are several separate drives (for example, HDD + SSD, see "Drive type") — this item indicates the volume of the most capacious drive (in our example — HDD).

A larger drive allows you to store more data, but it also comes at a higher cost. At the same time, it is worth remembering that the price also depends on the type of media: for example, SSDs are much more expensive than hard drives of the same volume. So it is best to directly compare drives of the same type with each other. As for specific volumes, the most modest figures are typical for configurations with pure solid-state memory — SSD of one type or another or eMMC (see "Drive type"): among them you can find solutions for 240 – 360 GB and even 128 GB or less . Hard drive capacity actually starts at 480 – 512 GB ; 1TB storage capacity is average, and the most capacious modern laptops are equipped with storage of 2TB or even more.

The connection interface used by the M.2 SSD installed in the laptop (see "Drive type").

One of the features of the M.2 connector and drives for it is that they can use two different connection interfaces: PCI-E (in one form or another) or SATA. We emphasize that this paragraph indicates the data of the SSD module; the connector itself may provide other interface options, including more advanced ones — see "M.2 connector interface" (for example, a drive with a PCI-E 3.0 2x connection can be placed in a connector that also supports the faster PCI-E 4.0 4x). However, anyway, the connection connector usually allows you to realize all the features of the installed drive; so this item allows you to quite reliably evaluate the capabilities of the standard M.2 module.

As for specific interfaces, nowadays you can mainly find the following options:

— SATA 3. The SATA interface was originally designed for traditional hard drives. The third version of this interface is the latest; it provides data transfer rates up to 600 Mbps. This is significantly less than PCI-E, and in general, very little by the standards of SSD drives. Therefore, M.2 connection using SATA is typical mainly for low-cost entry-level modules. However, even these media are generally faster than most HDDs.

— PCI-E. Universal interface for connecting internal peripherals. Provides generally faster speeds than SATA, making it better suited for SSD modules: theoretically, PC...I-E allows you to realize the full potential of SSDs, even the fastest. In fact, the supported data transfer rate may be different — depending on the version of the interface and the number of lines (data transmission channels). Here are the options most relevant for modern laptops:

• PCI-E 3.0 2x. Connection using 2 lanes PCI-E version 3.0. This version provides speeds of about 1 GB/s per line; respectively, two lines give a maximum of just under 2 GB / s.
• PCI-E 3.0 4x. Connection using 4 lanes PCI-E version 3.0. Provides a maximum speed of about 4 GB / s.
• PCI-E 4.0 4x. Connection using 4 lanes PCI-E version 4.0. In this version, the throughput, compared to PCI-E 3.0, has been doubled — thus, 4 lines give a maximum speed of about 8 MB / s.

Note that in the case of M.2 connectors, different PCI-E variations are usually quite compatible with each other — except that the connection speed when working with a "non-native" connector will be limited by the capabilities of the slowest component. For example, when connecting a PCI-E 3.0 4x SSD module to a PCI-E 3.0 2x slot, this speed will correspond to the capabilities of the connector, and when connected to PCI-E 4.0 4x, to the capabilities of the drive.

The interface of the main M.2 connector provided in the laptop.

In this case, the main slot is considered to be the one in which the SSD M.2 drive is installed (see "Drive type"). The interface of the drive itself is indicated separately (see above), and the interface of the connector is specified if the connector supports a more advanced type of connection than the device installed in it. An example is the following situation: the device itself works according to the SATA or PCI-E 3.0 2x standard (see "M.2 drive interface" above), and the connector on the board is capable of working with the PCI-E 3.0 4x interface.

Such information will be useful, first of all, for evaluating the possibilities for upgrading a laptop (with replacing a standard SSD module with a faster one). Nowadays, in this paragraph, you can mainly find the following options:

— PCI-E 3.0 2x. In fact, the most modest PCI-E standard found in M.2 ports of modern laptops: connection using 2 lanes of PCI-E version 3.0. This version provides speeds of about 1 GB/s per line; respectively, two lines give a maximum of just under 2 GB / s.

— PCI-E 3.0 4x. Connection using 4 lanes PCI-E version 3.0. Provides a maximum speed of about 4 GB / s.

— PCI-E 4.0 4x. Connection using 4 lanes PCI-E version 4.0. In this version, the bandwidth, compared to PCI-E 3.0, has been doubled — thus, 4 lines give a maximum speed of about 8 GB / s.

— PCI-E. Connection...via PCI-E, for which the manufacturer did not specify the details (version and number of lines).

Recall that in the case of M.2 connectors, different PCI-E options are quite compatible with each other — except that the speed will be limited by the capabilities of a slower component. In fact, this means that, for example, in an M.2 connector with a PCI-E 3.0 4x interface, it is quite possible to connect a drive for PCI-E 3.0 2x or PCI-E 4.0 4x; in the first case, the speed will be limited by the capabilities of the drive, in the second, by the capabilities of the connector.

The presence in the laptop of an additional compartment for an internal drive of the form factor 2.5 ".

Usually, to install or remove a drive in such a bay, it was not necessary to disassemble the entire laptop — just remove the cover or remove the plug. As for 2.5", this is the traditional form factor for hard drives (HDD) for "laptop" purposes, although other types of media (SSD and SSHD — see "Media Type") can be produced in this format. For connection 2.5 "storage drives normally use the SATA connector — it is not as fast as more modern standards like M.2 PCI-E (see "Drive Interface"), however, it is cheaper, and for HDD this connector is quite enough.

Thus, the presence of an additional 2.5" bay allows you to quickly and cost-effectively increase the total volume of laptop drives.

The number of additional M.2 connectors on the laptop motherboard.

In this case, any free M.2 connector is called additional (if there is an installed drive, the connector is considered the main one and its characteristics are given above — see "M.2 connector interface" and so on). There may be several such free slots — therefore, our catalog specifies the number of additional M.2 connectors, and not just their presence.

Anyway, this parameter will be useful primarily if the laptop is bought for an upgrade. It allows you to estimate how many M.2 SSDs (or other peripherals with such a connection) can be additionally installed in the device. At the same time, when choosing specific components, you should also take into account the interface and the size of free M.2 slots (see below for more details).

A connection interface supported by the laptops optional M.2 connector (see above). Recall that this connector is initially free; so this information allows you to evaluate the compatibility with additional components and, accordingly, the possibility of upgrading.

Two main types of interfaces can be implemented through the M.2 connector: SATA and PCI-E. SATA was originally created for hard drives, its support is inexpensive, but the speed of such a connection does not exceed 600 MB / s — this is very low by the standards of SSDs and other modern peripherals. Therefore, in the additional connector (s) M.2, one or another type of PCI-E is most often implemented. This interface has several variations that differ in version, number of lines and, as a result, speed; Here are the options most relevant for modern laptops:

— PCI-E 3.0 2x. Connecting using 2 lanes of PCI-E version 3.0 gives a maximum speed of just under 2 GB / s.
— PCI-E 3.0 4x. Connection using 4 lanes PCI-E version 3.0. Provides a maximum speed of about 4 GB / s.
— PCI-E 4.0 4x. Connected using 4 lanes PCI-E version 4.0, throughput is about 8 Mbps.
— PCI-E. Connection via PCI-E, for which the manufacturer did not specify the details (version and number of lines).

It is worth noting here that in the case of M.2, different versions of PCI-E are quite compatible with each other (except that the speed of work will be limited by the capabilities of the slower side —...the drive or connector). Therefore, even if the specific capabilities of such a connector are not specified, this is generally not critical (these capabilities will not hurt to clarify unless if high performance is fundamentally important to you).

The size of an additional slot for a drive (or other peripherals) with an M.2 interface provided in a laptop.

We emphasize that in this case we are not talking about the actually installed drive, but about the size of the bay (recall, there is no drive in it initially — for more details, see "Additional M.2 connector"). Knowing this size, you can estimate the maximum dimensions of the SSD module (or other component) that can fit in this bay. It is worth noting here that the most widespread nowadays are M.2 boards with a width of 22 mm, slots in laptops are usually made for this standard width. Therefore, the main indicator that determines size compatibility is length.

For bays on laptop motherboards, the length is most often 80 mm (marking 22x80 mm). This allows you to install 22 mm M.2 boards with a length of 80 mm, 60 mm, 42 mm and 30 mm — that is, all types of such boards, except for the largest, at 110 mm. The latter, however, is not a disadvantage, since 110-mm components are rarely used in laptops. If there are several additional (free) M.2 slots and they differ in size, these data are also specified in this paragraph, for example, “22x80 / 22x42 mm”.