Comparison AL-KO GT 2000 2.5 Ah vs Daewoo DABC 420

The type of engine that drives the cutting tool of the lawn mower, and in self-propelled models, the device itself. At the moment, the following types of engines are used:

— Electric (mains). Mains powered motor. Its advantages are low noise level, low cost and ease of operation (no need to buy fuel and oil) and no emissions into the atmosphere. Among the shortcomings can be called a relatively small power and a short range, limited by the length of the power cord.

— Electric (battery). Electric motor powered by its own built-in battery. It has all the same advantages as a mains-powered motor; in addition, such devices are not limited in movement, since they do not require a network connection during operation. On the other hand, the battery life of battery lawn mowers rarely exceeds half an hour, the battery weighs a lot and takes a long time to charge, and the power of such devices is even lower than that of network ones (despite the fact that they are noticeably more expensive).

— Petrol. Gasoline internal combustion engine. The advantages of such engines, in comparison with electric ones, are independence from the mains connection and high power, which allows you to work with dense thick vegetation. On the other hand, gasoline engines are heavier, more expensive to run, require the purchase of fuel and lubricants, and emit exhaust gases into the...air.

— Diesel. A type of internal combustion engine. In terms of basic features, diesel engines are almost identical to those described above, but they also have their own characteristics. On the one hand, in such units it is easier to provide high power and good torque, so they are better suited for "heavy" tasks; and diesel fuel is cheaper than gasoline. On the other hand, diesel engines themselves are more expensive, heavier and more difficult to operate. Therefore, they are not particularly popular among lawn mowers, this option is found mainly in riders (see "Type"), where high power is more important than the mentioned disadvantages.

— Gas. A rare variety of internal combustion engines that use a propane-butane mixture of gas as fuel. Their advantages over gasoline units are economical consumption, high mowing performance, and a small amount of harmful emissions into the atmosphere. In addition, gas fuel reduces the load on the engine, which, in turn, prolongs its operational life. The reverse side of the coin is the need to fill the cylinder with liquefied hydrocarbon gases at specialized filling complexes or the frequent replacement of gas cartridges.

— Without engine(manual). Lawnmowers that are not equipped with any motors and use the muscular strength of the user — when working, it is necessary to push the device in front of you. The advantages of such a scheme are low cost (both the device itself and its operation), independence from fuel and electricity, and maximum environmental friendliness; disadvantages are the relatively low quality of work and the significant expenditure of physical strength.

The capture width provided by the unit, in other words, the width of the strip of land cultivated in one pass. In fact, this size corresponds to the width of the working nozzle.

The large working width is useful when processing large open spaces, as it allows you to finish the job in a small number of passes. On the other hand, for hard-to-reach places, relatively narrow tools are better suited, able to go where a wider unit will not fit. In addition, the width of the tool directly affects the weight and price.

In general, it makes sense to compare in terms of working width only units of the same type (see above). However, it is worth noting here that trimmers do not differ so much from each other — most models capture from 25 to 45 cm (and a wide processing band is provided by moving the nozzle from side to side). As for the other types, in the most modest models the capture width does not exceed 40 cm, in the heaviest and most powerful it can be 56 – 60 cm or even more(in mini tractors — up to 1.5 m).

The width (diameter) of the trimmer knife characterizes the size of the paddle knife (or saw blade). Such a nozzle has a smaller capture width than a fishing line, however, it allows you to mow more dense thickets, including shrubs.

The location of the engine on the trimmer bar. Most petrol trimmers and high powered electric trimmers are overhead motorized – given the latter's significant weight, this is the best option in terms of balance. In turn, for low-power electric trimmers, the motors are lightweight and can be located below — this arrangement allows you to significantly shorten the trimmer shaft and reduce power losses when transmitting rotation to the working tool. Thus, bottom-mounted trimmers are usually significantly lighter, but have less power, do not cope well with thick dense vegetation and are poorly suited for work in wet weather due to the risk of electric shock (the latter, however, applies to all electric lawn mowers regardless of type) .

There are also models whose engine is carried on the back like a backpack. The shoulder-mounted engine is a convenient way to reduce the strain on the operator's hands.

— Direct. In straight bar trimmers, the rotation from the engine is transmitted to the cutting tool using a straight rigid shaft. This design is considered optimal for medium to high power trimmers, although the straight stem shape may not be perfect in terms of ease of use.

— Curved. A curved rod may be more convenient to use than a straight one, however, such trimmers have low power due to the fact that the rotation from the engine to the working tool is transmitted to them using a thin metal cable — such a transmission is not designed for high loads.

The type of handle provided in the design of the trimmer or combisystem (see "Type").

The choice for this parameter depends primarily on the personal preferences of the user, however, there are also quite objective differences between different types. The types themselves can be:

— Bicycle. A handle in the form of a pair of characteristic "horns" on either side of the trimmer bar, reminiscent, in accordance with the name, of a bicycle handlebar. This design allows you to comfortably mow the grass and perform other similar work; it is good in that the user's hands are in the most natural position when holding the tool. In addition, we note that the handles are convenient for both right-handers and left-handers. The disadvantage of models with bicycle handles is the relatively large weight and dimensions, as well as poor suitability for cutting branches and other work "at height". However, in the case of trimmers, such a need arises extremely rarely (especially since there are specialized varieties of garden tools for this — brush cutters and pole saws). Therefore, it is this option that has received the greatest popularity in modern trimmers.

— Loop -shaped. The handle, which looks like a characteristic loop, usually in the shape of the letter D. The role of the second handle in such a tool is usually played by the back of the bar, and the trimmer controls are also located there....In general, this design is considered less convenient than a bicycle one: the user has to either hold the tool with the barbell to the side, or pull one hand back strongly. On the other hand, the loop-shaped handle gives good vertical manoeuvrability and allows you to work both at ground level and much higher, and you can easily change the height of the nozzle. As a result of all this, although this option is less popular than the “bike”, it is still quite common, mainly on relatively light and low-power trimmers.

The diameter of the fishing line supplied with the trimmer (more precisely, with a reel attachment, see "Tips").

In modern models, this parameter can be from 1 to 4 mm. At the same time, a thicker fishing line handles better with dense thickets, but it works rougher, the treated lawn is not particularly even, and for the effective operation of such a nozzle, a fairly powerful engine is needed. On the other hand, a fine line provides a clean and neat cut, but is not suitable for heavy vegetation and large stems. Thus, thick fishing line is usually equipped with powerful units designed for "launched" lawns with an abundance of thick stems. Thin, on the other hand, is found mainly in low-power electric trimmers with a lower engine location, designed for neat lawns with regularly cut grass.

We also recall that many trimmers have the ability to replace the standard reel with another one that differs in line thickness.

— Adjustment of the tilt of the rod. Possibility to tilt the rod or the working head relative to the rod. The setting will come in handy for mowing grass in hard-to-reach places. Trimmers with this function are much more convenient to work under swings, benches and garden furniture. Also, by adjusting the tilt of the rod, you can adjust the grip of the trimmer to the height of the user.

— Telescopic rod. Possibility of increasing the length of the trimmer by extending the rod. Due to design features, this solution is available only for models with a lower engine and helps to maximally adjust the device for a person of any height.

— Collapsible rod. Possibility to disassemble the trimmer rod into several parts. This feature greatly simplifies storage and transportation: packing, carrying and transporting side-by-side components is easier than a solid long rod. In theory, this design is less reliable than a non-removable design, but trimmers are usually not subjected to such high loads that this would be noticeable.

- Belt. The strap for carrying the trimmer is a shoulder or backpack strap. This design significantly simplifies the operator’s task and reduces operator fatigue: carrying it with a belt is not as tiring as holding the tool in your...hands. The shoulder strap is supposed to be worn over one shoulder. It helps you control the trimmer better and reduces fatigue, especially during long periods of use. A more complex backpack strap system allows you to distribute the weight of the tool on both shoulders and back. In this implementation, the belt will not slip off the shoulder when wearing the trimmer. Please note that in models without a belt, it may be possible to purchase it separately. However, it is easier (and often cheaper) to immediately buy a tool with this accessory.

— Limit bracket. The bracket acts as a limiter and is designed to protect tall (necessary) vegetation from mowing. Those. you can extend a small structural element at the base of the rod, which, when approaching the bushes, will move them away, thereby not cutting them off. The bracket will also be appropriate when mowing an area with a fence, decorative landscape with many elements that can be damaged during mowing, or can once again “shorten” the fishing line by breaking its ends.

— Rotating head. Possibility of rotating the trimmer working attachment on the rod. Typically this function is used to move the cutting system from a horizontal to a vertical position. Vertical cutting can be useful, for example, for leveling edges and creating borders in lawns.

— Edging roller. The roller is necessary for a neat “haircut” between the lawn and the sidewalk. It is found in models with a rotating head and is designed for more comfortable work. Since the device does not need to be suspended, leaning on the roller makes it much easier to edge flower beds, decorative elements on the lawn, borders, etc.

— Support rollers. Special rollers mounted on the cutting head of the trimmer. Thanks to such rollers, you can rest the head on the ground and roll the tool in front of you - this is more convenient than carrying it “on yourself”. Another advantage is that the rollers support the working attachment at the same height, which means that mowing is as accurate as possible, almost like using a regular lawn mower (with all the advantages of a trimmer). The main disadvantages of models with rollers are the high cost, as well as increased weight, which makes it difficult to work “off the ground.”

— Blade knife. A knife in the form of a pair of blades, rotating around a vertical axis in the manner of propeller blades. Two blades are the most popular, almost standard option for rotary lawn mowers (see “Cutting system”). Note that in the case of trimmers, using a knife allows you to achieve higher performance and cope better with thick grass than using a reel with fishing line. On the other hand, the blades do not tolerate contact with stones and other hard objects very well; in case of such troubles, various tricks may be provided (for example, automatic engine brake).

— Spindle knife. Attachments used in spindle-type lawn mowers. For more information about such units, see “Cutting system”; here we would like to remind you that spindle blades are inferior to blade blades in terms of productivity and efficiency in thick grass, but they provide a cleaner cut, which allows you to give the lawn the most neat appearance possible. So this option is well suited for regularly trimming relatively sparse, well-groomed vegetation.

- Reel with fishing line. Most often used in trimmers (see “Type”). According to the general principle of operation, it is similar to a blade knife (see above), however, the working tool in this case is not blades, but pieces of thick fishing line rotating at high speed. The main advantage of a fishing line over a bladed knife is it...s almost complete insensitivity to collisions with stones and other hard objects: upon impact, such a “blade” will simply bend and literally immediately straighten due to centrifugal force. True, such attachments cope somewhat worse with thick stems, but in practice everything depends on the thickness of the fishing line (see above) and the speed of its rotation.

— Cultivator. An attachment designed to loosen the soil. Externally, it is a set of gears mounted on a horizontal axis with teeth of a specific curved shape. Due to the rotation of these wheels, loosening is carried out. Combisystems are mainly equipped with such attachments (see “Type”). At the same time, the width of the cultivator is usually small; it is poorly suited for full-fledged garden work, but it can be useful when cultivating a small flower bed or several beds.

— Saw blade. Attachment for cutting relatively thick woody stems (for example, bushes or small tree branches). Installed mainly on trimmers (see “Type”). Externally, this attachment is very similar to the working element of a circular saw: it uses a rotating rim with characteristic teeth along the edges. The disc may have holes to reduce weight.

— Scissor mower. In this case, we mean a special attachment, most often used in mowers (see “Type”). This attachment has the appearance of a characteristic horizontal “comb” with two rows of teeth moving relative to each other. Its design is described in more detail in the paragraph “Cutting system - Scissor”, but here we note that trimmer-mowers are indispensable when working with dense vegetation and thick stems; they can easily cope with thickets that are too tough for other attachments.

— Brush cutter. As a rule, the brush cutter attachment is used in trimmers (see “Type”). It is a long blade with teeth for trimming and trimming bushes or hedges, and trimming small tree branches.

— Without attachments. Absence of any attachments in the standard configuration of the lawn mower. It is assumed that the customer will purchase them separately for specific needs.