Power
Rated power of the oven installed in the stove. Specified only for electric ovens (see above). When determining this parameter, the power of all heaters and other devices installed in the oven (grill, convector, motorized spit, etc.) is taken into account; in other words, this item indicates the maximum power consumption.
This data is useful primarily for assessing electricity consumption, as well as the connected load during operation. But only ovens with similar functionality can be compared with each other in terms of power — for example, two models with convection. Otherwise, the comparison may be incorrect.
Oven cleaning
It is the method of cleaning the inner surface provided in the design of the oven. In addition to traditional and more advanced
steam cleaning, there are
catalytic and
pyrolytic cleaning. More about them:
— Traditional. This option assumes the absence of any devices that facilitate cleaning: you have to wash the oven manually, using ordinary detergents and cleaning products. Such a procedure can be quite troublesome and time-consuming, but such ovens are much cheaper than similar models with more advanced types of cleaning.
— Pyrolytic. Cleaning with high temperature. Dirt on the interior surfaces of the oven is burned to ash, which can then be easily removed without using detergents. At the same time, pyrolytic cleaning equally effectively handles all types of dirt, both new and old. The disadvantages of such a system are the duration of cleaning (sometimes up to several hours), high cost, and significant consumption of resources (electricity or gas, depending on the type of oven). In addition, during the operation of the cleaning system, unpleasant odours often arise, generated by the combustion of contaminants in the oven.
— Catalytic. Ovens with this type of cleaning have a special coating on the inner surface that breaks down grease on the oven walls. Fat disintegration is accelerated at high temperatures; the oven is thus self-cleaning t
...o a certain extent. However, the efficiency of catalytic cleaning is lower than that of pyrolytic cleaning. It is unable to cope with the entire amount of fat on the walls. Therefore, such an oven should be washed from time to time. On the other hand, ovens with catalytic cleaning are cheaper than ones with pyrolytic cleaning. And the cleaning itself does not require additional electricity/gas costs, nor is time-consuming (except for washing/wiping).
— Steam cleaning. Cleaning the oven with heated steam. A certain volume of water is poured into a baking sheet or another container, the container is placed in the oven and the cleaning mode is turned on. Due to heating, the water evaporates, and the heated steam softens the dirt on the walls and partially disintegrates the fat. After the end of the programme, it is enough to wipe the oven with a damp cloth. Such a cleaning requires less time and resources than pyrolysis and often turns out to be more effective than catalytic — steam can soften even old dried-up contaminants. At the same time, these ovens are relatively inexpensive. At the same time, this mode does not guarantee to cope with any contamination. It is possible that after the end of the steam cleaning, the oven will have to be washed traditionally.Turbo burners
The number of gas burners in which the flame is located not in one, as in standard burners, but in two (or three) rows — in other words, in the form of two (three) rings, one inside the other. Such burners have more power than traditional single-row ones and heat the bottom of the pan more evenly, which can be especially useful when frying. On the other hand, the need for such a heating mode arises quite rarely, and much more gas is consumed than during the operation of a classic burner. As a result, even in advanced stoves, the number of
turbo burners rarely exceeds 1.
Burner grates
It is the material from which the burner grates of the stove are made. This parameter is relevant only for gas burners — electric hobs do not have grates.
— Steel grates. The most common type of grates is steel grates coated with a special heat-resistant enamel. They are quite practical, reliable, have a relatively small weight and neat appearance, and at the same time are inexpensive, due to which they are often found in entry-level and middle-level models. The main disadvantage
of steel grates can be called the difficulty in cleaning from adhering contaminants — too intensive cleaning can damage the enamel. In addition, they are less durable than cast iron ones, and under heavy dishes containers, they can deform — as a result, the dishes will not stand stably on the stove, and the grate will most likely have to be replaced.
— Cast iron grates.
Cast iron grates is much heavier than steel ones. Moreover, they often look more massive and rough. On the other hand, they are more reliable, durable and stable, can cope even with heavy weights and keep their working shape much longer. In addition, cast iron is easier to clean: although dirt comes off worse than enamel, in extreme situations it is quite possible to use abrasive products without fear of damaging the surface.
Country of origin
The country in which, according to the manufacturer, the model is manufactured. Despite the fact that most of the capacities are concentrated in
China, European factories (
in Poland,
Slovenia,
Romania,
Turkey,
Czech Republic, etc.) for the production of household appliances have not gone away. And some models can be produced there. In general, such a division into a Chinese or European factory should not particularly affect the quality of products, but the stereotype of a reliable European assembly is present in us. However, it is possible that the model may have a country of manufacture, for example, Poland, and in the store under the same article, you will meet China.