Comparison Gorenje K 5241 XF stainless steel vs Gorenje K 5351 XF stainless steel

The lowest temperature the oven can provide. Usually, it is in the range of +30 to +50 ˚C. So, for example, the minimum heating temperature at +30 ˚C allows you to defrost products. Models with a minimum of 40 ˚C and 50 ˚C allow you to heat ready meals, heat tableware (before serving), dry rusk, etc.

It is the method of cleaning the inner surface provided in the design of the oven. In addition to traditional and more advanced steam cleaning, there are catalytic and pyrolytic cleaning. More about them:

— Traditional. This option assumes the absence of any devices that facilitate cleaning: you have to wash the oven manually, using ordinary detergents and cleaning products. Such a procedure can be quite troublesome and time-consuming, but such ovens are much cheaper than similar models with more advanced types of cleaning.

— Pyrolytic. Cleaning with high temperature. Dirt on the interior surfaces of the oven is burned to ash, which can then be easily removed without using detergents. At the same time, pyrolytic cleaning equally effectively handles all types of dirt, both new and old. The disadvantages of such a system are the duration of cleaning (sometimes up to several hours), high cost, and significant consumption of resources (electricity or gas, depending on the type of oven). In addition, during the operation of the cleaning system, unpleasant odours often arise, generated by the combustion of contaminants in the oven.

— Catalytic. Ovens with this type of cleaning have a special coating on the inner surface that breaks down grease on the oven walls. Fat disintegration is accelerated at high temperatures; the oven is thus self-cleaning t...o a certain extent. However, the efficiency of catalytic cleaning is lower than that of pyrolytic cleaning. It is unable to cope with the entire amount of fat on the walls. Therefore, such an oven should be washed from time to time. On the other hand, ovens with catalytic cleaning are cheaper than ones with pyrolytic cleaning. And the cleaning itself does not require additional electricity/gas costs, nor is time-consuming (except for washing/wiping).

— Steam cleaning. Cleaning the oven with heated steam. A certain volume of water is poured into a baking sheet or another container, the container is placed in the oven and the cleaning mode is turned on. Due to heating, the water evaporates, and the heated steam softens the dirt on the walls and partially disintegrates the fat. After the end of the programme, it is enough to wipe the oven with a damp cloth. Such a cleaning requires less time and resources than pyrolysis and often turns out to be more effective than catalytic — steam can soften even old dried-up contaminants. At the same time, these ovens are relatively inexpensive. At the same time, this mode does not guarantee to cope with any contamination. It is possible that after the end of the steam cleaning, the oven will have to be washed traditionally.

Type of tray guides provided in the oven.

— Frame. The simplest guides are made in the form of a fixed grid, and sometimes in the form of slots in the walls of the oven. They are quite practical and inexpensive, due to which they are used in the vast majority of ovens. The main disadvantage of the lattice guides can be called the fact that the baking sheet moves rather tightly in them, especially if the oven has not been cleaned for some time and the guides are dirty.

— Telescopic. Guides in the form of retractable tray support based on telescopic rails. When removing the baking sheet, the mechanism moves apart, and the stand, rolling on a special roller, “leaves” the oven. The main advantage of the "telescopic rails over the classic frame guides is that you do not need to make much effort to install and remove the baking sheet — it will move very easily. On the other hand, such devices are more expensive and more complicated than classic frame guides; as they get dirty, their efficiency drops noticeably, and dirt can completely disable the mechanism. In light of all this, manufacturers most often use telescopic rails not as the main option but as an addition to the frame guides described above. If telescopic guides are initially indicated in the specs of the stove, this usually means that the oven with traditional frame guides is additionally equipped with removable telescopic guides. These advanced telescopic rails ca...n be easily set at the desired level and removed for cleaning.

Many ovens, initially equipped only with frame guides, can be equipped with telescopic rails, purchased separately.

The type of automatic switch-off provided in the design of the stove.

Auto-off can be provided for the hob(hob), for the oven, or for both at once, regardless of whether the hob and oven are gas or electric. This function is implemented through a timer, after which the device turns off.

A display on the stove control panel. Usually, it is a very simple one-colour display : 3-4 digits plus a few additional characters (for example, a thermometer icon and a clock icon). However, even on such a display, almost all important information related to the stove operation can be displayed: heating temperature, clock, timer settings, and other relevant data. Thus, the display significantly simplifies the management of the stove and makes it more convenient.

For technical reasons, this function is mainly used in electric stoves; there are also gas models with displays, but they are extremely few.

The country in which, according to the manufacturer, the model is manufactured. Despite the fact that most of the capacities are concentrated in China, European factories ( in Poland, Slovenia, Romania, Turkey, Czech Republic, etc.) for the production of household appliances have not gone away. And some models can be produced there. In general, such a division into a Chinese or European factory should not particularly affect the quality of products, but the stereotype of a reliable European assembly is present in us. However, it is possible that the model may have a country of manufacture, for example, Poland, and in the store under the same article, you will meet China.