Comparison Pioneer PLX-500 vs Reloop RP-2000M

The type of pickup (cartridge) supplied with the turntable.

- MM(with moving magnet). The most common type of cartridges nowadays. The electrical signal in such devices is created by the oscillation of a moving magnet connected to the pickup stylus between special coils. These cartridges give a good output level, making them compatible with the simplest phono stages, they are easy to set up, and the needles in many models can be replaced by the user himself.

- MC(moving coil). Pickups in which the magnets are made stationary, and the signal is created by a moving coil that vibrates from the vibrations of the needle. This design allows you to reduce the mass of moving parts (compared to MM), which has a positive effect on the accuracy and reliability of sound transmission: MC cartridges are capable of transmitting almost all the nuances of sound. On the other hand, their output signal level is low, which puts forward increased demands on the quality of phono stages and significantly affects the cost. So pickups of this type are typical mainly for high-end equipment.

- MI (with a movable iron element). Quite an exotic type of pickups: the coils and magnets in them are made stationary, and the vibration of the needle sets in motion a miniature piece of magnetic material (for example, iron), which moves between the coils and changes their inductance. Theoretically, such cartrid...ges can compete with MCs in terms of overall sound quality and detail, while MI technology allows you to achieve a high level of signal output, which does not require expensive phono stages. However, in fact, such pickups are rare for a number of reasons.

Anyway, for the normal operation of the player, a phono stage is required for the corresponding type of pickup; A phono stage may also be built-in (see “Characteristics”), however, if external equipment is used, it is necessary to know the type of pickup to select it.

The effective length of a tonearm in set is the distance from the attachment point (axis of rotation) to the stylus.

This indicator is important primarily for rotary tonearms: the longer the length, the lower the angular error, the smaller the discrepancy between the direction of movement of the track and the longitudinal axis of the pickup (for more details, see “Type”) and the lower the level of corresponding distortion. In addition, a longer length reduces the resonant frequency and reduces the likelihood of distortion. On the other hand, a longer tonearm turns out to be heavier, which requires certain technical tricks and can also negatively affect the purity of the sound. Therefore, a large length is not always a guarantee of high quality – you should also pay attention to weight (see below).

A phono corrector is a specially designed preamplifier used when working with vinyl record pickups. Initially, the sound on such records is recorded with distortion of the amplitude-frequency characteristic, namely with an increase in volume from low to high frequencies; this is due to the technical features of the recording process. Accordingly, the phono corrector not only amplifies the signal to a level sufficient for feeding to the power amplifier, but also corrects the amplitude-frequency characteristic, “pulling out” the bass and reducing the volume of the HF. And the built-in phono corrector allows you to connect the player to the power amplifier directly, without using intermediate equipment. True, in terms of characteristics, built-in preamplifiers-correctors are inferior to external ones. Therefore, some models with this function may provide a “bypass” mode, allowing you to pass the signal bypassing the built-in phono corrector to an external, more advanced one. And there are also vinyl players without a phono corrector at all.

— Tempo adjustment. The presence in the player of an electronic module that allows you to change the tone of the sound being played, in other words, to make it higher or lower by a certain interval, in other words, change the playback speed. This feature is also known as a "pitch controller". It is relevant primarily for DJ "turntables", as it allows you to mix tracks recorded in different keys. Some home players also have a tempo control, but its capabilities are much more modest, and a real need for such a function rarely arises.

— Adjustable counterweight. The ability to adjust the position of the counterweight mounted on the opposite end of the tonearm from the cartridge. This allows you to change the balance of the tonearm by adjusting the downforce (see above); the presence of an adjustable counterweight is highly desirable if you plan to use "non-native" pickups with the player.

— Anti -skating. The presence of an anti-skating system in the design of the tonearm. The peculiarities of the work of the vinyl player are such that during playback there is an additional force that presses the needle against the inside of the groove. This results in an imbalance in the sound of the stereo channels and uneven groove wear. To compensate for this phenomenon, anti-skating is used — a system that “pulls” the tonearm in the opposite direction, towards the ou...ter edge of the record. Anti-skating may be based on counterweights, springs, magnets, or other devices, but anyway, this function is considered highly desirable for modern turntables. However, it is not available everywhere: for example, in low-cost models, anti-skating may not be provided to reduce the cost, and in top-end devices it may be present, but not indicated in the specifications.

— Reverse playback. The reverse function allows you to play the record in reverse, playing the sound backwards. This feature is unlikely to be needed by audiophiles, but it is very much appreciated by DJs, as it expands the arsenal of available sound effects. Usually, direct drive is required for reverse (see above), although there are exceptions.

— Hitchhiking. A system that automatically stops the disc and raises the arm when the record has finished playing. Due to this, additional wear of the needle due to movement along the plate "idle" is prevented. However, in some situations (for example, when playing several records in a row), hitchhiking is inconvenient, so it can be turned off.

— Autoplay. The presence in the player of automatic playback. In such models, the user does not need to manually move the tonearm. In fact, it is enough to install the record, press the button — and the disc will start to rotate, the tonearm will lower itself to the desired position, and after the end of playback, the record will stop, the tonearm will rise (due to hitchhiking, see above) and return to its original position. Such systems make the player as convenient as possible, but they significantly affect its cost, and also (like any additional electronics) are a potential source of interference.

— Built-in acoustics. The presence in the player of its own speaker system, consisting of speakers and a power amplifier. This equipment allows you to listen to records without the use of external equipment; in fact, models with acoustics are stand-alone music centers, except that they work not on cassettes / discs / flash drives, but on vinyl discs. At the same time, the characteristics of the built-in amplifiers and loudspeakers are generally noticeably more modest than those of external ones, and additional electronics in the player's case can distort the signal. Therefore, it makes sense to purchase models with built-in acoustics if purity and high sound quality are not critical — for example, for listening to old records.

— Speed 78 rpm. The ability to operate the player at a speed of 78 revolutions per minute. To date, such records are almost never produced, but they were very popular until the 60s of the XX century. Therefore, to listen to vintage audio recordings, you will need a turntable with support for this speed. Note that 78 rpm operation may require additional equipment (such as a belt pulley or a special pickup).

— Write to media. The ability to connect an external media to the player and record the reproduced sound on it in digital form. Usually, we are talking about USB-drives (such as flash drives); accordingly, a USB Type A port is provided for their connection. However, other types of media, such as memory cards, may be supported. Recording directly to media is faster than digitizing via a computer (see "USB port (type B)" above), but the sound is recorded "as is" in this case, without the possibility of quality enhancement and noise filtering.

— Installation of the second tonearm. Possibility of installing an additional tonearm on the player, which can differ markedly from the main one both in its own features and in the characteristics of the pickup. This possibility is justified if the player is planned to be used in different modes that cannot be covered by a single pickup. For example, you can install an inexpensive pickup on the second tonearm, which is not a pity to “kill” on old worn records, or a 78 rpm cartridge for vintage recordings. Note that in some models there may be more than one additional tonearms.

— Pendulum alignment. Automatic turntable leveling system based on a pendulum (suspension). This feature is found exclusively in premium class models, designed for the highest mechanical precision. In such models, the player itself is installed on a special stand on the floor, and a massive (several tens of kilograms) pendulum is suspended from its lower part. While the pendulum hangs strictly vertically, the player's disc is in a strictly horizontal position; and due to the large mass, the suspension practically does not deviate from the vertical with small vibrations of the floor (for example, from people walking nearby). This feature is designed primarily for sophisticated audiophiles who want to get the most accurate and reliable sound.

The presence in the player of an electronic module that allows you to change the tone of the sound being played, in other words, to make it higher or lower by a certain interval, in other words, change the playback speed. This feature is also known as a "pitch controller".. It is relevant primarily for DJ "turntables", as it allows you to mix tracks recorded in different keys. Some home players also have a tempo control, but its capabilities are much more modest, and a real need for such a function rarely arises.

The range of frequencies that the player is capable of outputting when using a standard pickup.

The wider the frequency range, the more complete the sound picture will be, the less low and/or high frequencies will remain behind the scenes. However, from a practical point of view, it does not make sense to expand the range beyond the values \u200b\u200bof 16 – 22000 Hz — it is within these limits that the human ear hears the sound (and even then not everyone). In high-end audio equipment, including turntables, there are more extensive ranges; however, such characteristics are a kind of “side effect” of high-end technology that manufacturers use for advertising purposes.

In addition, we note that an extensive frequency range is not yet a guarantee of high-quality sound: the sound picture depends on many other parameters, from the amplitude-frequency response to extraneous interference.

Rated power consumed by the player during normal operation.

Modern turntables are very economical: most models, even those equipped with built-in acoustics (see "Features"), the power consumption does not exceed 15 W, and there is no need to talk about any serious impact on congestion in the electrical networks (as well as electricity bills). The exception is some premium-class devices, in which the weight of the platter (see below) reaches several tens of kilograms, and the corresponding engine power is required to rotate such a mass.

The material used for the base of the turntable - or, as it is also called, the support table.

The base is actually the body of the turntable; the tonearm, platter and drive are mounted on top of it. Note that a set of modern turntables can include both a base and a base with a tonearm, and the most extensive option, called a complete set, also includes a pickup. As for the materials for the base, they must meet specific requirements - in particular, they must be quite heavy to reduce extraneous vibrations transmitted to the device. Here are the most common materials:

- Plastic. The main and, in the case of vinyl players, practically the only advantage of plastic is ease of production and, accordingly, low cost. At the same time, the performance characteristics of such material are quite modest, so it is the prerogative of inexpensive “turntables”.

— Acrylic. Technically, acrylic is a type of plastic described on top, but in general this material is much more advanced in performance characteristics, is relatively inexpensive and can have an original appearance (in particular, it can be made transparent). Acrylic tables are typical for fairly solid models.

- Aluminum. Metal bases made of aluminum are massive and highly durable, b...ut they are not cheap, and therefore are found mainly in premium players.

— MDF/Fibreboard. Fiberboards, in addition to good acoustic characteristics, are notable for their pleasant appearance, especially suitable for retro-style devices. This material can be used in quite expensive models.

- Carbon. High-quality material, characterized by high strength and quite stylish appearance. On the other hand, it has a relatively low weight, which has to be compensated by the significant thickness of such bases, and this affects the cost (despite the fact that the material itself is not cheap anyway). Therefore, carbon has not gained much popularity.

- Granite. Natural granite is very heavy and dampens vibrations well, but it is also a very expensive material. It is used extremely rarely, mainly in premium players, not only for the sake of practical characteristics, but also to emphasize the level of the device.

The diameter of the disc on which the record is placed.

The standard diameter of a 33 rpm vinyl record is 12", or 300 mm. The diameter of the platter can differ from this value in one direction or the other; in normal listening to music this does not play a special role, but for a DJ " turntables, it is desirable that the disk be wider — due to this, it is more convenient to control the rotation.