Comparison Justfog Minifit Starter Kit vs Eleaf iCare 2 Kit

— Starter kit. A set also known as a “kit” or “box mod”. It includes everything you need for vaping — both a battery mod and an atomizer; in other words, a “kit” is a ready-to-use electronic cigarette (except that in some models the battery has to be purchased separately). At the same time, this category includes both relatively inexpensive and simple devices and high-end models. In any case, starter kits will be appreciated by tech who do not want to select a battery mod and atomizer separately and would like to immediately receive a device whose components are optimally compatible with each other.

— POD system. A specific type of electronic cigarette that uses replaceable cartridges — “pods” — instead of traditional atomizers. Each cartridge consists of an evaporator and a container with liquid; the “pod” can be either open (with the ability to refill at your discretion) or closed (disposable, supplied filled and thrown away when the liquid supply is exhausted). In any case, POD systems are usually sold as ready-made kits, which have a number of advantages over traditional vapes. Firstly, cartridges are relatively inexpensive and take up very little space; as a result, you can carry several “pods” with different flavors and/or strengths at once, changing them in a battery mod as desired. Secondly, the battery mods themselves...are more compact and lighter than in regular electronic cigarettes, they are more convenient to carry and do not attract as much attention. Thirdly, POD systems are extremely easy to maintain - in fact, there is no point in making replaceable cassettes serviceable. Among the disadvantages of such devices, one can note the relatively small capacity of batteries and reservoirs in cassettes, although there are exceptions.

— Disposable. Disposable POD systems are vaping devices without the ability to fill liquid and recharge the battery. The liquid reservoir in their design has a certain volume, and a specific battery capacity is selected for it (based on the specified number of puffs). When the “disposable” runs out of vaping liquid or the battery runs out, the device can be thrown away. Due to their compact size, disposable electronic cigarettes easily fit into a pocket, a small compartment of a bag or backpack. Also, they often lack controls and settings - the heating element is activated as soon as the customer takes a puff. In terms of flavor, there are many different options for disposable POD systems on the shelves.

— Atomizer. A separately sold vaporizer of an electronic cigarette — that is, the part where the vapor is generated; for operation, the vaporizer is installed on a battery mod (see below). Some types of such devices are also called "clearomizers", but this term is used less and less often; nowadays, all vaporizers are usually united under the term "atomizer". Be that as it may, the overall impressions of the vape are mainly influenced by the characteristics of the vaporizer: in particular, the taste and richness of the vapor, as well as the ability to customize the vapor to your preferences, directly depend on them. So in order to change the sensations of vaping, it is enough to try a different atomizer. In addition, when buying a new vape, many users (especially experienced ones) prefer not to rely on ready-made starter kits, but to choose an atomizer and a battery mod separately, at their discretion.

— Battery mod. The part of the electronic cigarette responsible for powering the evaporator (atomizer). The functionality of such a mod can be different - from the simplest container for a replaceable battery with an on/off button to an advanced device with complex control electronics and advanced capabilities (see "Battery mod"). Be that as it may, separately sold battery mods are designed for tech who want to assemble an electronic cigarette according to individual requirements, without relying on the starter kits.

The volume of the liquid tank provided in the design of the atomizer. Note that this parameter can be specified even for squonk atomizers (see "Filling type"): although they work with an external tank, however, a certain amount of "liquid" can fit in the evaporator itself.

The larger the tank, the more liquid you can keep in an electronic cigarette and the less often you have to refill it. On the other hand, capacious tanks have the appropriate dimensions, and too large a tank would be inconvenient, and liquids are consumed relatively little even in one long session of soaring. As a result, a volume of more than 6 mL is already considered quite large for vapes, and in the smallest models this figure does not exceed 2 mL.

Also note that when choosing a tank capacity, manufacturers usually take into account the resistance of the spiral, the power of the battery (if it is included) and other parameters that affect the expected flow rate of the liquid. There is no hard dependency here, however, in general, more powerful atomizers are usually equipped with larger tanks.

— Upper. The traditional type of filling was initially quite popular, but now such atomizers are gradually giving way to bottom filling models. The main advantage of this option is the ability to pour liquid without turning the atomizer over and without removing the flask from the battery mod. However refilling usually requires disassembly — for example, unscrewing the cap with the mouthpiece.

— Lower. This option assumes that for refueling, you need to turn the atomizer upside down and pour liquid from the bottom side. At first glance, this procedure is less convenient than top filling, but it provides an important advantage for serviced heaters: if necessary, you can remove and rewind the base without draining the liquid from the tank. Note that squonk format drip atomizers are formally also refueled from below, however, they have their own specifics, therefore they do not belong to this category and are allocated separately; see below for details.

— Side. Refueling through a special hole in the side of the atomizer. Like the top one, this design allows you not to remove the flask from the battery mod; the opening usually opens and closes easily and quickly, without the need, for example, to unscrew the cap. This option is quite popular in baco drips (see "Type of atomizer"), althou...gh it is also found in other varieties.

— Squonk. A specific type of bottom filling used in models with drip atomizers (see "Type of atomizer"). These vapes have a rather large e-liquid reservoir installed in the battery mod, and each time you press a special button (or the elastic wall of the reservoir), the liquid is fed into the atomizer in small portions directly through the connector. This design eliminates the main drawback of drip atomizers — the need to constantly add liquid manually, "drop by drop": instead of the hassle of manual refueling, it is enough to periodically press the button. At the same time, most of these evaporators allow installation on a regular battery mod, without a squonk — for this, the kit provides a replaceable connector of a standard design, without a channel for supplying liquid; and on battery mods with a squonk, usually, you can put ordinary atomizers without restrictions. The disadvantages of this option can be somewhat higher cost than analogues with traditional types of refueling.

The type of blowing provided in the atomizer of an electronic cigarette.

This parameter is indicated by the location of the cells for the intake of air entering the evaporator. According to this criterion, lower, upper and side airflow are distinguished, here are their main features:

— Lower. The most popular option nowadays. Such popularity is primarily due to the fact that many vapers consider the “lower” vapor to be the most delicious. In addition, bottom blown atomizers are easier to maintain than "side" models, they are not so demanding on winding quality. The disadvantages of this option include an increased likelihood of leakage, including during liquid overflow; and the condensate, which is quite intensively formed at the air intakes, tends to flow down onto the battery mod. However, these points are not particularly critical.

— Upper. A format that has appeared relatively recently. In general, such an airflow conveys taste somewhat worse than the lower one, moreover, the steam turns out to be hotter; however, this point is largely subjective, and some users like this type of steam. The objective advantages of the “upper” atomizers include the minimum probability of overflow, the almost complete absence of condensate flowing onto the battery mod, and the absence of splashes even when using coils with very low resistance.

— Si...de. The type of blowing used mainly in "drips" (see "Type of atomizer"). If the bottom airflow gives the most delicious steam, then the side airflow is the most dense and saturated. This is achieved due to the fact that the air flows around the spiral as intensively as possible and captures the greatest amount of evaporation. In addition, the likelihood of liquid overflow and splash formation in such atomizers is very small, and with the right settings, the taste is transmitted almost as well as in the “lower” models. The main disadvantage of this option is the actual need for careful tuning and proper installation of the spiral — so that there are no blind spots on it. So side airflow is generally designed for experienced users; maintenance-free atomizers are an exception, but this format of operation is rarely used in them.

Also note that there are combined options for sale, for which two types of airflow are indicated at once. Here the specifics can be different. So, it is unrealistic to combine the upper and lower airflow in one evaporator, therefore this option is indicated only for sets of several atomizers with different types of airflow. But the side format of work may well be combined with the top or bottom — this allows you to combine the advantages of both options and provide saturated steam. On the other hand, the need for careful tuning for such devices is just as relevant as for "pure" side ones.

The smallest resistance of the heating coil of an electronic cigarette.

The meaning of this parameter will be different, depending on which part of the device is in question (see "Type"). So, for atomizers, this parameter is given if spare heaters are supplied in the kit — accordingly, it is indicated for the “head” with the lowest resistance. For a battery mod, this is the smallest resistance that can be connected to it. And in starter kits, the minimum resistance is also usually indicated by the battery mod; low-resistance "heads" in such cases may or may not be included in the delivery.

Anyway, data on the minimum resistance is important in the mutual selection of an atomizer and a battery mod (including when creating custom windings) — connecting an atomizer with too low resistance is fraught with overloads and various unpleasant consequences, up to fire. However, this parameter is of particular importance for lovers of the so-called subohm — soaring at a low heater resistance (up to 1 ohm), which allows you to achieve high steam saturation (when the resistance decreases, the power increases). Not all batteries are capable of working with sub-ohm heaters, so the suitability of a battery mod for such vaping needs to be clarified.

The highest resistance of the electronic cigarette heating coil.

The meaning of this parameter will be different, depending on which part of the device is in question (see "Type"). For an atomizer, this can be either the resistance of the complete heater, or, if there are several “heads” in the kit, the resistance of the highest-resistance replaceable coil. For a battery mod, the highest resistance is indicated at which the battery is able to deliver sufficient power for operation. For the starter set, the data is usually given according to the battery mode, while the resistance of the complete heater (heaters) may be lower than the maximum.

Data on the maximum and minimum (see above) resistance is necessary, first of all, to select an atomizer and a battery mod that are compatible with each other. The atomizer must fall within the operating range of the battery mod, otherwise the battery will either be overloaded (if the evaporator resistance is too low), or simply will not provide the desired degree of heating (if it is too high).

The battery capacity of an e-cigarette or separately sold battery mod. This parameter is indicated only for models with non-removable batteries (see "Battery type"): replaceable cells can be produced in different capacities.

The larger the battery, the longer you can use the device without recharging the battery. However the actual power consumption and, accordingly, the battery life of different models will be different, therefore, only devices with similar operating voltages and atomizer resistances can be compared in terms of capacity.

In general, if battery life is important to you, it is quite possible to proceed from the principle “the more capacious the battery, the better”; and to save money, you can choose a relatively weak battery. It is also worth mentioning that there are schemes for calculating the optimal battery capacity depending on the power, atomizer resistance, etc.; these schemes can be found in special sources.

The maximum power supplied by the battery.

This is one of the main parameters of the battery pack that determines its compatibility with the atomizer. Starter kits (see "Type"), by definition, include atomizers that are optimally suited to a given battery in terms of power, and this parameter is mainly of reference value. But when choosing components separately, you should pay special attention to it. Higher power allows you to achieve more saturated steam, but only up to certain limits — too much heating leads to a deterioration in taste, and even burning of the wick (which, all the more, does not contribute to improving the sensation of soaring). So the atomizer must normally transfer the power of the battery, otherwise, at best, you will have to constantly limit the power with the help of a varivolt or variwatt (see "Battery mod"), and at worst, normal use will be impossible at all.

Note that for classic evaporator tanks with one spiral, power up to 40 W is considered sufficient; more powerful batteries are designed mainly for advanced serviced models, drip atomizers and bacodrips(see "Type of atomizer") that have more than one coil and, accordingly, are more high consumption in terms of energy consumption. Also note that the actual heating power depends on the voltage, and in fact it may be lower than the claimed one, depending on the resistance of the atomizer. See “Maximum voltage".

The highest voltage that the battery mod can supply to the atomizer.

Knowing the minimum (see above) and maximum voltage, it is possible to estimate the heating power that the battery is able to provide at a certain resistance of the atomizer. For example, if we have a battery mod with a voltage range of 3.3 – 4.8 V and an atomizer with a 1.8 Ohm coil, then the current strength at the minimum voltage will be 3.3 / 1.8 ≈ 1.8 A, and at maximum 4.8 / 1.8 ≈ 2.7 A. Accordingly, the smallest heating power will be 3.3 * 1.8 ≈ 6 W, and the largest 4.8 * 2.7 ≈ 13 W. In this case, the nominal power of the battery can be higher, but not vice versa — the actual power cannot be more than the nominal. Let's say, theoretically, the battery from our example, combined with a 0.15 Ohm sub-ohm atomizer, even at the minimum voltage, should produce a current of 3.3 / 0.15 = 22 A and a power of 3.3 * 22 = 72.6 W. However, if a power of 50 W is claimed in the characteristics, then higher values \u200b\u200bare impossible to achieve, even if you unscrew the regulator to the maximum — at low resistances, the voltage at the battery output drops sharply.