Comparison Denon PMA-1700NE vs Denon PMA-1600NE

In itself, the signal-to-noise ratio is the ratio of the level of pure sound produced by the amplifier to the level of extraneous noise that occurs during its operation. This parameter is the main indicator of the overall sound quality — and very clear, because. its measurement takes into account almost all the noise that affects the sound in normal operating conditions. A level of 70 – 80 dB in modern amplifiers can be considered acceptable, 80 – 90 dB is not bad, and for advanced audiophile-class devices, a signal-to-noise ratio of at least 100 dB is considered mandatory.

If the specifications do not specify for which output the signal-to-noise ratio is indicated, it usually means its value for the linear input (see "RCA (par)"). This is quite enough to evaluate the quality of the device for this parameter. However, some manufacturers indicate it for other inputs — Main, Phono; see below for more on this.

signal-to-noise ratio when the amplifier is driven through the Phono input. This interface is for connecting turntables; its features are described in the “Inputs” section below, and for the meaning of any signal-to-noise ratio, see the corresponding section above.

The damping factor describes the quality of interaction between the amplifier and the speaker system connected to it.

Due to the design features, any speaker is prone to the occurrence of so-called parasitic oscillations — oscillations that continue after the main impulse from the amplifier has ceased (similar to how a string continues to vibrate after a pluck). This phenomenon has a negative effect on sound quality, and manufacturers use various means to reduce it to an absolute minimum; suppression of parasitic oscillations is called damping.

The most effective type of damping is electrical, by reducing the output impedance of the amplifier. The lower this resistance, the better the amplifier keeps the speakers from unnecessary vibrations. To evaluate this effect, they introduced the concept of “damping factor” (damping factor) — the ratio of the load resistance (impedance) to the output resistance of the amplifier. The minimum value of such a coefficient for Hi-Fi class equipment is 20; indicators at the level of 100 – 120 can be called good, and among the Hi-End segment there are numbers of the order of several thousand.

At the same time, it is worth noting that when increasing to three-digit numbers, the original meaning of this parameter is, in fact, lost, and other points appear. The most important of them from a practical point of view is that models with a high damping factor are very demanding on the quality of the connection to t...he speakers — the high resistance of cables and connectors can negate the damping properties of the amplifier itself. There are other nuances associated with this indicator (in particular, recommendations for choosing an amplifier and speakers for each other); they are described in detail in specialized sources.

The sensitivity and dynamic impedance of the amplifier when a signal is applied to the balanced XLR input.

Under the sensitivity of any input (except optical) is meant the lowest signal voltage at this input, at which the amplifier is able to provide normal nominal power values (see "Power per channel (8Ω)"). This parameter determines, first of all, the requirements for the signal source. On the one hand, the voltage provided by this source must not be lower than the input sensitivity of the amplifier, otherwise the latter simply will not give the claimed characteristics. However, a significant excess in voltage should not be allowed, otherwise the sound will begin to be distorted. More detailed recommendations on choosing an amplifier by sensitivity are described in special sources.

For any input other than optical, it is believed that the higher this indicator, the less distortion the amplifier introduces into the signal. The minimum level of input impedance in modern models is considered to be 10 kOhm, and in high-end devices it can reach several hundred kOhm.

The sensitivity and dynamic impedance of the amplifier when a signal is applied to the RCA line input.

Under the sensitivity of any input (except optical) is meant the lowest signal voltage at this input, at which the amplifier is able to provide normal nominal power values (see "Power per channel (8Ω)"). This parameter determines, first of all, the requirements for the signal source. On the one hand, the voltage provided by this source must not be lower than the input sensitivity of the amplifier, otherwise the latter simply will not give the claimed characteristics. However, a significant excess in voltage should not be allowed, otherwise the sound will begin to be distorted. More detailed recommendations on choosing an amplifier by sensitivity are described in special sources.

For any input other than optical, it is believed that the higher this indicator, the less distortion the amplifier introduces into the signal. The minimum level of input impedance in modern models is considered to be 10 kOhm, and in high-end devices it can reach several hundred kOhm.

The sensitivity and dynamic impedance of the amplifier when a signal is applied to the Phono MM/MC input.

Under the sensitivity of any input (except optical) is meant the lowest signal voltage at this input, at which the amplifier is able to provide normal nominal power values (see "Power per channel (8Ω)"). This parameter determines, first of all, the requirements for the signal source. On the one hand, the voltage provided by this source must not be lower than the input sensitivity of the amplifier, otherwise the latter simply will not give the claimed characteristics. However, a significant excess in voltage should not be allowed, otherwise the sound will begin to be distorted. More detailed recommendations on choosing an amplifier by sensitivity are described in special sources.

For any input other than optical, it is believed that the higher this indicator, the less distortion the amplifier introduces into the signal. The minimum level of input impedance in modern models is considered to be 10 kOhm, and in high-end devices it can reach several hundred kOhm.

Signal level and dynamic impedance provided by the device at the preamplifier output (see "Outputs" for details).

The signal level must not be lower than the sensitivity of the power amplifier (see "Type") to which the signal is received — otherwise the power amplifier will not be able to provide a normal signal level already at its outputs.

Dynamic resistance (impedance) of the preamplifier output. This value is exactly the same as the input impedance of the REC output — see the relevant paragraph above. For more information about the exit itself, see "Exits".

— Preamplifier (Pre-Amp). The presence in the design of the device of a separate output for the signal from the preamplifier. In the type of amplifiers of the same name (see "Type"), such an output is available by definition and is the main, and sometimes the only one. On integrated models (see ibid.) , the Pre-Amp output allows you to connect an external power amplifier and use it instead of the internal one. This feature can be useful, for example, to connect a more powerful speaker instead of the original one, or to work in Bi-amping mode. It is worth noting that the Pre-Amp output can also be installed in power amplifiers, playing the role of a "splitter".

— Subwoofer. The presence in the amplifier design of a separate subwoofer output. Usually, such an output uses an RCA connector (see "Input to the amplifier (Main)"), and the function itself is implemented through a crossover, which selects the low-frequency range in the signal and redirects it to a subwoofer. The "own" output makes it much easier to connect a subwoofer : it does not require any additional equipment, the amplifier itself is enough. This usually provides for the possibility of working with any type of subwoofer — both passive and active; however, in the first case, you will need an additional external amplifier.

— Coaxial S/P-DIF. The presence in the design of the amplifier of the S / P-DIF output of an electric typ...e, with signal transmission via a coaxial cable. For more information about this interface, see the relevant paragraph in the "Inputs" section.

— Optical. The presence in the design of the amplifier output for transmitting a digital audio signal over a fiber optic cable TOSLINK. For more information about this interface, see the relevant paragraph in the "Inputs" section.

— Jack (6.35 mm). Presence of TRS type outputs in the design of the amplifier. These outputs are jacks for 6.35 mm Jack plugs and may look like the corresponding headphone jack (see below). However, this similarity is misleading: TRS produce sound on the principle of "one channel per plug" (an exception may be information amplifiers). This type of Jack connector is found mainly in high-end professional amplifiers.

— Speakon. An interface used in professional audio equipment to connect acoustics to a power amplifier. It has become widespread in high power equipment, including concert amplifiers (see "Intended Use"), due to its increased reliability and suitability even for working with very powerful audio signals. But in household appliances it is rarely used.

— Control output (IR). The control output allows the amplifier's built-in IR receiver to be used to control other components in the audio system, such as a DVD player in another room, out of range of the remote control, from the remote control. With this scheme of operation, the amplifier actually plays the role of a remote sensor, receiving commands and transmitting them through the control output to another device. Note that the very presence of such inputs and outputs does not guarantee the compatibility of various devices, especially if they are produced by different manufacturers; Sharing details should be clarified in the official documentation.

— Display. The presence of a display on the front panel of the amplifier. Such displays may have a different design and size, but they are all used to display service information: operating mode, selected signal source, special notifications, overload messages, errors, etc. This provides additional ease of use.

— Indicators. In this case, it means that there are indicators on the front panel that indicate the currently used signal source. Usually they look like a row of light bulbs with the appropriate signatures — "Phono", "CD", "Tuner", "AUX", etc. Such pointers are not as versatile as the display, but they are still very convenient.

— Arrow indicators. Presence on the front panel of indicators in the form of scales with arrows. Usually, such indicators are designed to display the peak level of the output signal. They make it easy to track overloads, and many users find this option more convenient and visual than displays. In addition, the arrow scales give the amplifier a stylish appearance, and, unlike the same displays, do not have complex electronics that can distort the sound. However, this category also includes other types of indicators with scales; some of them may not use an arrow, but other indicators (for example, light ones).

— Regulators behind a hidden panel. The presence of a cover on the front panel that hides the controls of the amplifier. Many models are e...quipped with additional controls on the front panel; they can be used to adjust both the sound — volume, bass / treble, balance, etc. — and other operation parameters (for example, selecting a signal source or switching between the main and additional speakers). Sometimes these controls (as well as the front panel inputs) are provided with a cover, usually for aesthetic reasons. an abundance of small elements would give the device a sloppy appearance. The cover can also perform protective functions — for example, it reduces the amount of dust that enters the connectors.

— Input audio jack. The presence on the front panel of an input for connecting an audio signal — usually linear, in analogue format. On the one hand, such an input greatly simplifies work with signal sources that need to be connected only occasionally and for a short time — for example, MP3 players: the front panel is always in sight, while getting to the connectors on the back is sometimes very difficult. On the other hand, usually the role of the front audio jack is played by AUX IN with a 3.5 mm mini-Jack jack. This connector is not used among the main inputs, but it is quite popular in portable electronics, in particular, the players already mentioned. Some models may have a pair of RCA jacks on the front panel (see "RCA (pair)"), but this option is less common.

— Headphone output. Headphone output on the front panel of the amplifier. Headphones are portable devices, and on average you have to reconnect them significantly more often than most other components of the audio system; the output located on the front panel greatly simplifies the process.