Car Jacks

Perfect for garage use, or for the home motor enthusiast, these durably constructed car ramps can be used together to lift vehicles of 2000kg or less to provide access for maintenance purposes. They can also be used to gain the clearance needed to insert a bottle jack. The solid frames of the ramps are fitted with rungs to prevent slippage of the wheel after the car has been raised, & an extended rear face allows the car ramps to be stood upright for convenient, space saving storage. For low ground clearance vehicles, an extension is available for purchase separately (part number: RM1). Specifications: • Capacity per Pair: 2000kg • Length: 790mm • Car Ramp Height: 250mm • …

Texspan round slings are manufactured from 100% polyester. The sling is made up with a seamless outer polyester cover and a core produced from a continuous hank of high-tenacity polyester. They are softer than duplex slings and kinder to delicate surfaces. BS EN1492: 2000 compliant. NB Length quoted are for the effective working length, which is half the circumference of the sling . A full range of effective working lengths is also available from 0.5m to 6m and strength ratings in excess of 2 tonnes up to a maximum of 6 tonnes. Working Load Limit: 1 tonne x 1.5 metre

• Steel chassis with PVC rollers and four ø100mm nylon castors.• Pedal operated hydraulic lifting action with safety locking pin when under load.• Rollers cradle vehicle’s tyre and are capable of handling up to 270mm in width.• Suitable for bodyshops, garages, showrooms or anywhere an immobile vehicle needs moving on an even surface.• Capacity: 650kg.• Maximum Opening: 550mm.• Maximum Tyre Profile: 270mm.• Weight: 17kg.• Note: Skates sold as singles, but must be used in pairs.Steel chassis with PVC rollers and four ø100mm nylon castors. Pedal operated hydraulic lifting action with safety locking pin when under load. Rollers cradle vehicle’s tyre and are capable of handling up to 270m…

• Approved to EU and UK Lifting Gear Regulations.• This hoist is intended for use where a suitable support facility exists.• Support brackets are included with the equipment.• N.B. Support bar is not included.Approved to EU and UK Lifting Gear Regulations. This hoist is intended for use where a suitable support facility exists. Support brackets are included with the equipment. The support bar is not included.• Approved to EU and UK Lifting Gear Regulations. • This hoist is intended for use where a suitable support facility exists. • Support brackets are included with the equipment. • Maximum Capacity (Double Cable): 250kg. • N.B. Support bar is not included. • Model No. PH250Technical Specification:Capaci…

Twin-piston, quick lift facility - just five pumps to reach maximum height
Lifting range 88-358mm
Integrated rubber saddle pad prevents damage to underside of vehicle
EVA foam handle to prevent panel damage
Knurled handle for extra grip
Twin safety overload valves
Rear swivelling castors
Manufactured to EN 1494 Specification
Draper 12 months parts and labour warranty

• Suitable for lower capacity single and twin cylinder engines.• Supports can rotate for accessibility to all parts of the engine.• Useful integral utility/drip tray.• Capacity: 30kg.Suitable for small capacity single and twin cylinder engines (maximum weight 30kg) and includes a utility/drip tray. Supports can rotate for accessibility to all parts of the engine.• Suitable for lower capacity single and twin cylinder engines. • Supports can rotate for accessibility to all parts of the engine. • Useful integral utility/drip tray. • Capacity: 30kg. • Model No. MES01Technical Specification:Capacity: 30kgEngine Support Span: 200-370mmHeight: 375mmLength: 535mmNett Weight: 7.89kgWidth: 320mmDimensions: L…

• Designed to support and accurately position engines during maintenance operations such as replacing anti-vibration mountings and certain body panels.• Also used as an aid for the removal of gearboxes and transmissions.• Beams supported on rubber feet and fine adjustment control is obtained by using a screw/hook mechanism.• Supplied with a short length of chain.Supports and accurately positions engine during maintenance operations such as replacing anti-vibration mountings and certain body panels. Also used as an aid for the removal of gearboxes and transmissions. Beam supported on rubber feet and fine adjustment control is obtained by using a screw/hook mechanism. Supplied with a short length o…

• Designed to prevent damage to the underside of the vehicle's jacking point.• Type C design.• Fits inside the jack saddle.Designed to prevent damage to the underside of the vehicle's jacking point. Design Type C. Profile Depth 15mm. Size ø94.5mm. Fits saddle ø95mm.• Designed to prevent damage to the underside of the vehicle's jacking point. • Design Type C. • Profile Depth: 15mm. • Size: ø94.5mm. • Fits saddle ø95mm. • Model No. JP13Technical Specification:Nett Weight: 0.09kgJack Pad Size: ø94.5mmStyle: Type CProfile Depth: 15mmTo Fit Saddle Size: ø95mmWeight: 0.17kgDimensions: Length: 15mm x Height: 190mmWeight: 0.1KgWarranty: Consumable

Base and reservoir machine welded for increased strength and reduced chance of leakage. Fitted with overload valve. Supplied with 2-piece handle. Supplied in a tough storage case and suitable for recovery trucks. The case prevents the jack from damaging other items and also prevents the spread of grease, oil or dirt. Features & Benefits: • Min./Max. Height: 175/339mm. • Fitted with overload valve. • Base and reservoir machine welded. • Supplied with 2-piece handle. • Tough storage case. • Model No. SJ2BMC Specifications: Model No SJ2BMC Brand: Sealey Capacity: 2 Tonne Hydraulic Lift: 116mm Maximum Height: 339mm Minimum Height: 175mm Nett Weight: 3.00kg Screw Extension: 48mm

Bottle jack, with hydraulic unit, max. load 15 t. Supplied = assembled. Max. load = 15 t. Lifting range with lifting head = 225 - 425 mm. Lift = 140 mm. Weight = 7.7 kg. Piston diameter = 48 mm. Base plate length = 135 mm. Base plate width = 142 mm. Additional height when unwound = 60 mm. Overall height from - to = 225 - 425 mm mm. Product type = hydraulic jacks. Pressure relief value protects the hydraulic unit from overloading. Large foot plate for extra stability. 2-part lever. The high quality hydraulic cylinder features a large foot plate for increased stability. The pump lever moves easily, and is driven by a 2-part lever with a fitting for the valve control. The saddle is ribbed and can …