Car Jacks

• Fully adjustable Subframe/Engine support adaptor.• Supplied with various designs of fittings to suit different applications.• To assist in the removal and fitting of complete engine assemblies, rear axles, gearboxes, fuel tanks, exhaust systems and other awkward loads.• Designed to fit directly on to the Sealey 500TTJ and 800TTJ Transmission Jacks.• Labour saving design allows jobs to be carried out by one person.• Easily fitted or removed from the transmission jack as required.The SFC01, fully adjustable Subframe/Engine Support Adaptor is supplied with various types of fittings to suit different applications. Designed to assist in the removal and fitting of complete engine assemblies, rear axles,…

• Min./Max. Height: 300/410mm.• Maximum Capacity: 150kg.• Powder coated pressed steel frame, to ensure strength and durability.• Ideal for use with off-road/trials bikes to easily lift the bike when needing to perform maintenance/servicing or cleaning.• Simple, one foot, step and lift mechanism means the bike can be instantly raised in one motion.• For added safety, features an ‘over centre’ locking toggle linkage to mechanically lock the lift at full height to prevent accidental lowering.• Also fitted with hydraulic dampener for controlled descent.Powder coated pressed steel frame, to ensure strength and durability. Ideal for use with off-road/trials bikes to easily lift the bike when needing …

• Approved to EU and UK Lifting Gear Regulations.• This hoist is intended for use where a suitable support facility exists.• Support brackets are included with the equipment.• N.B. Support bar is not included.Approved to EU and UK Lifting Gear Regulations. This hoist is intended for use where a suitable support facility exists. Support brackets are included with the equipment. The support bar is not included.• Approved to EU and UK Lifting Gear Regulations. • This hoist is intended for use where a suitable support facility exists. • Support brackets are included with the equipment. • Maximum Capacity (Double Cable): 250kg. • N.B. Support bar is not included. • Model No. PH250Technical Specification:Capaci…

Features & Benefits: • Jack Stands ideally suited to the professional trade workshop!• Manufactured from heavy duty steel• Pin type for added safety and strength• Pin wire strap secured to stand to prevent loss• Deep saddle for positive location under vehicle• Adjustable Height• Conforms to international standards CEMaterial: Heavy Duty SteelStandard: CECapacity: 1350kgMinimum Height: 255mmMaximum Height: 370mmLift Height: 110mmSaddle Diameter: 18 x 50 x 62mmBase Area: 195 x 180mm

Twin piston Rocket Lift feature brings saddle to maximum height in minimal strokes. Universal joint release mechanism allows safer, more controlled lowering of jack. Polyurethane wheels for smoother manoeuvrability and helps prevent damage to workshop floor. Profiled lifting arm gives low clearance height of just 85mm making it suitable for sports and custom cars. Heavy-duty steel chassis provides stability and endurance. Fitted with an overload valve for added safety. Hydraulic oil by-pass system protects ram from being overextended.

• Two rubber wheel chocks.• Prevents vehicle movement when being jacked on a level surface or parked on an incline not exceeding 12º.• Chocks supplied on rope for easy storage and removal from underneath wheels.Rubber wheel chocks weighing 8kg (4kg each) prevent vehicle movement when jacking or parking on an incline. Suitable for heavy commercial vehicles and light aircraft. Chocks supplied on rope for easy storage and removal from underneath wheels. Not intended for use on sloped ground over 12º.• Two rubber wheel chocks. • Prevents vehicle movement when being jacked on a level surface or parked on an incline not exceeding 12º. • Suitable for light aircraft, or vehicles below 30tonne. • Choc…

• Suitable for semi-permanent attachment to steel beams and acts as a lifting point for chain blocks, hoists and lifting tackle.• The clamp may also be used for lifting and transfer of steel beams and as a pulling clamp.• Low profile afforded by integral pivot/lifting point.Suitable for semi-permanent attachment to steel beams and acts as a lifting point for chain blocks, hoists and lifting tackle. The clamp may also be used for lifting and transfer of steel beams and as a pulling clamp. Low profile afforded by integral pivot/lifting point.• Suitable for semi-permanent attachment to steel beams and acts as a lifting point for chain blocks, hoists and lifting tackle. • The clamp may also be us…

• Off-road base compatible with most high-lift farm jacks.• Designed to spread ground force of jack to prevent sinkage on soft surface.• Includes handle coupler to lock most high lift farm jacks handle in position for secure transportation.• Base size 184 x 185mm.Technical SpecificationNett Weight: 1.35kg

The Sealey VS0110 Under Vehicle Engine/gearbox Support is ideal when replacing clutches or timing belts The Sealey VS0110 is an under vehicle engine/gearbox support that is fully adjustable, making the unit suitable for most transverse and in-line configurations. Designed to support the engine or gearbox when mountings or gearbox are being removed. This unit removes the need for using a transmission jack or engine support beam. Features:
- Ideal when replacing clutches or timing belts
- Removes the need for using a transmission jack or engine support beam
- Fully adjustable, making the unit suitable for most transverse and in-line configurations
- Designed to support the engine or gearbox …

Ratchet type axle stands with cast iron support posts. Angled teeth in post prevent accidental release of load - the more weight applied, the tighter the post is locked. Sold in pairs. Features & Benefits: • Min./Max. Working Height: 285/420mm. • Capacity: 6 Tonne per pair. • Ratchet type with cast iron support posts. • Tough steel-plate welded bases. • Sold in pairs. • Model No. VS2003