Car Jacks

• Two composite wheel chocks.• Prevents vehicle movement when being jacked on a level surface or parked on an incline not exceeding 12°.• Suitable for cars not exceeding 2 tonne gross weight.Two composite wheel chocks. Prevents vehicle movement when being jacked on a level surface or parked on an incline not exceeding 12°. Suitable for cars not exceeding 2 tonne gross weight.• Two composite wheel chocks. • Prevents vehicle movement when being jacked on a level surface or parked on an incline not exceeding 12 degrees. • Suitable for cars not exceeding 2tonne gross weight. • Model No. WC09Technical Specification:Dimensions (W x D x H): 80 x 185 x 100mmMaterial: CompositeNett Weight: 0.44kg…

• Two rubber wheel chocks.• Prevents vehicle movement when being jacked on a level surface or parked on an incline not exceeding 12º.• Chocks supplied on rope for easy storage and removal from underneath wheels.Rubber wheel chocks weighing 8kg (4kg each) prevent vehicle movement when jacking or parking on an incline. Suitable for heavy commercial vehicles and light aircraft. Chocks supplied on rope for easy storage and removal from underneath wheels. Not intended for use on sloped ground over 12º.• Two rubber wheel chocks. • Prevents vehicle movement when being jacked on a level surface or parked on an incline not exceeding 12º. • Suitable for light aircraft, or vehicles below 30tonne. • Choc…

Faithfull Lifting Slings are made from 100% PES polyester duplex webbing that is lightweight but extremely durable for use on awkward loads, offering a soft alternative to wires and chains. All sizes can be used in straight pull, basket or choke configurations. Fitted with a reinforced, sleeved lifting eye. Meets the requirements of EN 1492 Part 1:2000. Minimum breaking load is 7 times the Working Load Limit.The Faithfull Green Lifting Sling has the following specifications: Max. Load: 2 Tonne.Width: 60mm.Length: 2m.Additional Information:• Length: 2.0m• Type: Lifting Sling• Load Capacity: 2000kg• Breaking Strength: 14000kg

Flat arm with spring loaded roller bearings for use with SJBEX3000S and SJBEX4000S Jacking Beams. When unloaded these arms support the weight of the beam, allowing for it to run smoothly along the pit edge. In position, and when the beam is under load, the bearings retract, to leave the flat of the arm, to stabilise the lift.Features & Benefits:• Flat arm with spring loaded roller bearings for use with SJBEX3000S and SJBEX4000S Jacking Beams.• When unloaded these arms support the weight of the beam, allowing for it to run smoothly along the pit edge.• In position, and when the beam is under load, the bearings retract to leave the flat of the arm to stabilise the lift.• Model No. SJBEX.A01Speci…

• Heavy-duty 7 Tonne high level support stand.• Safely supports vehicles when wheel free operations are being carried out.• Independently UK load tested. • Sturdy welded steel construction for superior safety and strength.• Three types of large interchangeable crutches for good load distribution.• Supplied with captive pin load support.• Fitted with retracting castors for easy manoeuvrability.• Suitable for commercial and public service vehicles.• Sold as singles, but MUST be used in pairs, or multiples of.Heavy-duty high level stand to safely support vehicles when wheel free operations are being carried out. Independently UK load tested. Supplied with three interchangeable crutches for even …

Single-piece hydraulic unit with heavy base design. Integral cog-type release mechanism and long 2-piece handle. Protective jack handle sleeve helps prevent accidental damage to car bodywork when pumping the handle. Heavy-duty castors and extra-large saddle design ease positioning under vehicle. Fitted with safety overload valve and pump-through valve to prevent handle locking at maximum ram extension. Ideal for loaded vans up to 3.5 Tonne GVW. Features & Benefits: • Min./Max. Saddle Height: 130/520mm. • Chassis Length: 659mm. • Integral cog-type release mechanism and long 2-piece handle. • Heavy-duty swivel castors and extra-large saddle design ease positioning under vehicle. • Fitted with safet…

Bottle jack, with hydraulic unit, max. load 3 t. Supplied = assembled. Max. load = 3 t. Lifting range with lifting head = 168 - 318 mm. Lift = 100 mm. Weight = 2.3 kg. Piston diameter = 23 mm. Base plate length = 95 mm. Base plate width = 93 mm. Additional height when unwound = 50 mm. Overall height from - to = 168 - 318 mm mm. Product type = hydraulic jacks. Pressure relief value protects the hydraulic unit from overloading. Large foot plate for extra stability. 2-part lever. The high quality hydraulic cylinder features a large foot plate for increased stability. The pump lever moves easily, and is driven by a 2-part lever with a fitting for the valve control. The saddle is ribbed and can also …

Designed for the jacking points to protect and prevent damage to side skirts and battery. Made from high quality rubber, providing a sturdy and durable point of contact. Features a rubber O-ring on the spigot, creating a secure fit to the vehicle. Features & Benefits: • Designed for the jacking points to protect and prevent damage to side skirts and battery. • Made from high quality rubber, providing a sturdy and durable point of contact. • Features a rubber O-ring on the spigot, creating a secure fit to the vehicle. • Model No. JPT4 Specifications: Model No JPT4 Application(s): Suitable for Models S and X Brand: Sealey Nett Weight: 0.72kg

Designed to support and accurately position engines during maintenance operations such as replacing anti-vibration mountings and certain body panels. Also used as an aid for the removal of gearboxes and transmissions. Beams supported on rubber feet and fine adjustment control is obtained by using screw/hook mechanisms. This model has the additional advantage of a 360 adjustable rotating cross beam to enable a greater range of support options when in use.

• Suitable for semi-permanent attachment to steel beams and acts as a lifting point for chain blocks, hoists and lifting tackle.• The clamp may also be used for lifting and transfer of steel beams and as a pulling clamp.• Low profile afforded by integral pivot/lifting point.Suitable for semi-permanent attachment to steel beams and acts as a lifting point for chain blocks, hoists and lifting tackle. The clamp may also be used for lifting and transfer of steel beams and as a pulling clamp. Low profile afforded by integral pivot/lifting point.• Suitable for semi-permanent attachment to steel beams and acts as a lifting point for chain blocks, hoists and lifting tackle. • The clamp may also be us…