Car Jacks

• Replacement hydraulic ram for SC10LR.V3 engine crane.Technical SpecificationNett Weight: 11kgRam Capacity: 7257kgRam Diameter: 30mmRam Travel: 480mmPump Type: Single SpeedRam Pin Hole Diameter: 16.5mmClevis Pin Hole Diameter: 16.5mmMounting Point Distance (Min): 650mmOverall Length (Min): 665mmBase mount Type: Double ClevisTechnical Specification:Capacity: 7257kg Diameter: 30mmDimensions: Length: 710mm x Height: 150mmWeight: 9.99KgWarranty: 1 year

• Weight-for-weight, this strap is three to five times stronger than chain and has the advantage that overload can be detected early by the fraying of the strap.• Manufactured from 100% high strength polyester with reinforced lifting eyes.• Colour-coded according to European standards for identifying capacity.• Safe working load ratings quoted are for a load between the loop eyes (U configuration) and a load at one end (straight configuration).Weight-for-weight, this strap is three to five times stronger than chains and have the advantage that overload can be detected early by the fraying of the straps. Manufactured from 100% high strength polyester with reinforced lifting eyes. Colour-coded accordin…

Powerful – the pneumatic car jack uses 5 to 10 bar compressed air to effortlessly raise vehicles up to 3000 kg with the aid of air cushions
Fast – the air jack for cars reaches its 40 cm maximum lifting height in just 5 s, so you can get to work right away
Safe – a large base and a support with a diameter of 10 cm provides stability to the air cushion car jack, while an overpressure valve protects against excessive loads
Flexible – the two handles with rubberised ends ensure the pneumatic jack is always in the optimum position
Stable – built with steel and featuring three air cushions, the construction is robust and durable, while an adjustable inner cylinder provides added stability when exten…

• Rubber saddle pad.

• Suitable for use with our lever hoists or chain blocks.• Designed for mounting onto an I-beam or RSJ to allow load to be manoeuvred sideways.• Incorporates wheel guards to prevent contact with other trolleys mounted on same load bearer.Suitable for use with our lever hoists or chain blocks. Designed for mounting onto an I-beam or RSJ to allow load to be manoeuvred sideways. Incorporates wheel guards to prevent contact with other trolleys mounted on same load bearer.• Suitable for use with our lever hoists or chain blocks. • Designed for mounting onto an I-beam or RSJ to allow load to be manoeuvred sideways. • Incorporates wheel guards to prevent contact with other trolleys mounted on same load…

• A low profile trolley jack designed for domestic and light-duty commercial use • Enables the elevation of vehicles of up to 2 tonnes to heights between 85 and 430mm • The trolley jack has a twin piston quick-lift feature • The integrated rubber saddle pad prevents damage to the underside of the vehicle • Rear-swivelling, hard-wearing nylon wheels give quiet, smooth operation and prevent damage to garage and workshop floorsThis low profile trolley jack is designed for domestic and light-duty commercial use and enables the elevation of vehicles of up to 2 tonnes to heights between 85 and 430mm. The trolley jack has a twin piston pump for fast lifting and an integrated rubber saddle pad to pre…

Everbuild Black Jack 902 Bitumen & Flashing Primer is a thin black primer used to give a key prior to applying bitumen paints and roof coatings. Also suitable as a primer prior to applying Black Jack Flashing Tape.

For repairs and maintenance. Suitable for most standard cars. Platform height 200mm; platform width 205mm approx. Extensions are available to lower the angle for low ground clearance vehicles Stock No 23306. Sold loose.

• Made from durable polypropylene.• These ramps are designed to allow jacking access to suitable jacking points on the vehicle.• Not intended to raise a vehicle enough for under vehicle servicing.Made from durable polypropylene. These ramps are designed to allow jacking access to suitable jacking points on the vehicle. Not intended to raise a vehicle enough for under vehicle servicing.• 3tonne Capacity per pair. • Made from durable polypropylene. • These ramps are designed to allow jacking access to suitable jacking points on the vehicle. • Not intended to raise a vehicle enough for under vehicle servicing. • Overall Dimensions (L x W x H): 700 x 200 x 80mm. • Model No. CAR3000LRTechnical Specification:Capa…

Specifications:- Weight: 2,578kg- Ability: 1500kg- Application: Automotive- Plastic weight: 6g

Expert Quality, ideal for the workshop or factory use. The chain hoist has a triple spur geared shaft and pinion with load braking and double pawls. The compact gear housing allows use in areas of limited clearance. High quality welded chain with safety latches on the load hooks.