Car Jacks

The Sealey VS0110 Under Vehicle Engine/gearbox Support is ideal when replacing clutches or timing belts The Sealey VS0110 is an under vehicle engine/gearbox support that is fully adjustable, making the unit suitable for most transverse and in-line configurations. Designed to support the engine or gearbox when mountings or gearbox are being removed. This unit removes the need for using a transmission jack or engine support beam. Features:
- Ideal when replacing clutches or timing belts
- Removes the need for using a transmission jack or engine support beam
- Fully adjustable, making the unit suitable for most transverse and in-line configurations
- Designed to support the engine or gearbox …

• Approved to EU and UK Lifting Gear Regulations.• This hoist is intended for use where a suitable support facility exists.• Support brackets are included with the equipment.• N.B. Support bar is not included.Approved to EU and UK Lifting Gear Regulations. This hoist is intended for use where a suitable support facility exists. Support brackets are included with the equipment. The support bar is not included.• Approved to EU and UK Lifting Gear Regulations. • This hoist is intended for use where a suitable support facility exists. • Support brackets are included with the equipment. • Maximum Capacity (Double Cable): 250kg. • N.B. Support bar is not included. • Model No. PH250Technical Specification:Capaci…

Texspan round slings are manufactured from 100% polyester. The sling is made up with a seamless outer polyester cover and a core produced from a continuous hank of high-tenacity polyester. They are softer than duplex slings and kinder to delicate surfaces. BS EN1492: 2000 compliant. NB Length quoted are for the effective working length, which is half the circumference of the sling . A full range of effective working lengths is also available from 0.5m to 6m and strength ratings in excess of 2 tonnes up to a maximum of 6 tonnes. Working Load Limit: 3 tonne x 1 metre

• Designed to prevent damage to the underside of the vehicle's jacking point.• Type A design.• Fits over the jack saddle.Designed to prevent damage to the underside of the vehicle's jacking point. Design Type A. Profile Depth of 19mm. Size ø148mm. Fits saddle ø128-131mm.• Designed to prevent damage to the underside of the vehicle's jacking point. • Design Type A. • Profile Depth: 19mm. • Size: ø148mm. • Fits saddle ø128-131mm. • Model No. JP04Technical Specification:Nett Weight: 0.29kgJack Pad Size: ø148mmStyle: Type AProfile Depth: 19mmTo Fit Saddle Size: ø128-131mmWeight: 0.29kgDimensions: Length: 20mm x Height: 280mmWeight: 0.3KgWarranty: Consumable

• Weight-for-weight, this strap is three to five times stronger than chain and has the advantage that overload can be detected early by the fraying of the strap.• Manufactured from 100% high strength polyester with reinforced lifting eyes.• Colour-coded according to European standards for identifying capacity.• Safe working load ratings quoted are for a load between the loop eyes (U configuration) and a load at one end (straight configuration).Weight-for-weight, this strap is three to five times stronger than chains and have the advantage that overload can be detected early by the fraying of the straps. Manufactured from 100% high strength polyester with reinforced lifting eyes. Colour-coded accordin…

Expert Quality, for semi - permanent attachment to steel RSJ's to act as lifting point for chain blocks, hoists and lifting tackle. Can also be used for the lifting and transfer of steel beams and as a pulling clamp. Test certificate included. Carton packed.

• Increases the stability of the motorcycle by clamping the bottom and front of the tyre.• Features a pivot clamp which locks the front wheel securely by the motorcycle weight.• Suitable for fitting on trailers, in vans or to motorcycle lifts (requires suitable fixings).• Fully adjustable to fit wheels ø13"-21"(380-535mm).• Minimum/Maximum Tyre Width: 50-130mm.• Please note: Motorcycle must also be secured using tie down straps.• Fittings not supplied.Increases the stability of the motorcycle by clamping the bottom and front of the tyre. Features a pivot clamp which locks the front wheel securely by the motorcycle weight. Suitable for fitting on trailers, in vans or to motorcycle lifts (require…

• Steel frame designed for supporting and moving partly dismantled or badly damaged vehicles around the workshop or bodyshop.• Sliding castor brackets adjust for width and rubber-faced support pads adjust for height.• Fitted with four ø150mm nylon castors.• Max. Width: 1485mm.• Min./Max. Height: 300/390mm.Steel frame designed for supporting and moving partly dismantled or badly damaged vehicles around the workshop or bodyshop. Sliding castor brackets adjust for width and rubber-faced support pads adjust for height.• Steel frame designed for supporting and moving partly dismantled or badly damaged vehicles around the workshop or bodyshop. • Sliding castor brackets adjust for width and rubb…

Expert Quality, portable and compact twin stage pneumatic jack, capable of lifting 40 Tonnes. The 3 stage adjustable ergonomic handle is fixed with a "Slow Down" valve and a "Self-Return" switch for increased safety and easy use. Fitted with industrial quality seals prolonging the life of the jack, a safety overload valve and twin rubber coated wheels for a quieter and smoother operation, whilst also preventing damage to garage floors and improving manoeuvrability. Supplied with 45mm and 75mm height lift extensions and a 1/4" BSP airline connector. Manufactured, tested and certified to the current EN1494 standard.