Car Jacks

• Designed to prevent damage to the underside of the vehicle's jacking point.• Type A design.• Fits over the jack saddle.Designed to prevent damage to the underside of the vehicle's jacking point. Design Type A. Profile Depth 31.7mm. Size ø157mm. Fits saddle ø138-142mm.• Designed to prevent damage to the underside of the vehicle's jacking point. • Design Type A. • Profile Depth: 31.7mm. • Size: ø157mm. • Fits saddle ø138-142mm. • Model No. JP07Technical Specification:Nett Weight: 0.13kgJack Pad Size: ø157mmStyle: Type AProfile Depth: 31.7mmTo Fit Saddle Size: ø138-142mmWeight: 0.13kgDimensions: Length: 20mm x Height: 280mmWeight: 0.4KgWarranty: Consumable

Weight-for-weight, these straps are three to five times stronger than chains and have the advantage that overload can be detected early by the fraying of the straps. Manufactured from 100% high strength polyester with reinforced lifting eyes. Colour-coded according to European standards for identifying their capacity. Safe working load ratings quoted are for a load between the loop eyes (U configuration) and a load at one end (Straight configuration). Features & Benefits: • Weight-for-weight, this strap is three to five times stronger than chains. • Overload can be detected early by the fraying of the straps. • Manufactured from 100% high strength polyester. • Reinforced lifting eyes. • Capac…

Expert Quality, polyester webbing, 50mm wide, with reinforced lifting eyes. Colour coded to European standards to identify capacity. The safe working load (SWL) is rated at 1000kg for a load at one end (straight configuration) and 2000kg for a load between the loop eyes ('U' configuration). Shrink wrapped for security. Display packed.

• Two composite wheel chocks.• Prevents vehicle movement when being jacked on a level surface or parked on an incline not exceeding 12°.• Suitable for cars not exceeding 2 tonne gross weight.Two composite wheel chocks. Prevents vehicle movement when being jacked on a level surface or parked on an incline not exceeding 12°. Suitable for cars not exceeding 2 tonne gross weight.• Two composite wheel chocks. • Prevents vehicle movement when being jacked on a level surface or parked on an incline not exceeding 12 degrees. • Suitable for cars not exceeding 2tonne gross weight. • Model No. WC09Technical Specification:Dimensions (W x D x H): 80 x 185 x 100mmMaterial: CompositeNett Weight: 0.44kg…

• Two rubber wheel chocks.• Prevents vehicle movement when being jacked on a level surface or parked on an incline not exceeding 12º.• Chocks supplied on rope for easy storage and removal from underneath wheels.Rubber wheel chocks weighing 8kg (4kg each) prevent vehicle movement when jacking or parking on an incline. Suitable for heavy commercial vehicles and light aircraft. Chocks supplied on rope for easy storage and removal from underneath wheels. Not intended for use on sloped ground over 12º.• Two rubber wheel chocks. • Prevents vehicle movement when being jacked on a level surface or parked on an incline not exceeding 12º. • Suitable for light aircraft, or vehicles below 30tonne. • Choc…

Faithfull Lifting Slings are made from 100% PES polyester duplex webbing that is lightweight but extremely durable for use on awkward loads, offering a soft alternative to wires and chains. All sizes can be used in straight pull, basket or choke configurations. Fitted with a reinforced, sleeved lifting eye. Meets the requirements of EN 1492 Part 1:2000. Minimum breaking load is 7 times the Working Load Limit.The Faithfull Green Lifting Sling has the following specifications: Max. Load: 2 Tonne.Width: 60mm.Length: 2m.Additional Information:• Length: 2.0m• Type: Lifting Sling• Load Capacity: 2000kg• Breaking Strength: 14000kg

Flat arm with spring loaded roller bearings for use with SJBEX3000S and SJBEX4000S Jacking Beams. When unloaded these arms support the weight of the beam, allowing for it to run smoothly along the pit edge. In position, and when the beam is under load, the bearings retract, to leave the flat of the arm, to stabilise the lift.Features & Benefits:• Flat arm with spring loaded roller bearings for use with SJBEX3000S and SJBEX4000S Jacking Beams.• When unloaded these arms support the weight of the beam, allowing for it to run smoothly along the pit edge.• In position, and when the beam is under load, the bearings retract to leave the flat of the arm to stabilise the lift.• Model No. SJBEX.A01Speci…

• Heavy-duty 7 Tonne high level support stand.• Safely supports vehicles when wheel free operations are being carried out.• Independently UK load tested. • Sturdy welded steel construction for superior safety and strength.• Three types of large interchangeable crutches for good load distribution.• Supplied with captive pin load support.• Fitted with retracting castors for easy manoeuvrability.• Suitable for commercial and public service vehicles.• Sold as singles, but MUST be used in pairs, or multiples of.Heavy-duty high level stand to safely support vehicles when wheel free operations are being carried out. Independently UK load tested. Supplied with three interchangeable crutches for even …

Single-piece hydraulic unit with heavy base design. Integral cog-type release mechanism and long 2-piece handle. Protective jack handle sleeve helps prevent accidental damage to car bodywork when pumping the handle. Heavy-duty castors and extra-large saddle design ease positioning under vehicle. Fitted with safety overload valve and pump-through valve to prevent handle locking at maximum ram extension. Ideal for loaded vans up to 3.5 Tonne GVW. Features & Benefits: • Min./Max. Saddle Height: 130/520mm. • Chassis Length: 659mm. • Integral cog-type release mechanism and long 2-piece handle. • Heavy-duty swivel castors and extra-large saddle design ease positioning under vehicle. • Fitted with safet…