Car Jacks

Designed for use with the CR2 Car Ramp Extension Set (part number: TUPCR2), this pair of car ramp extensions fits onto the base of the ramps to provide a more gradual gradient for raising low ground clearance vehicles. It will prove invaluable if working with many types of sports car or custom vehicle. The Car Ramps are NOT included, & are available for purchase separately. Important Always use wheel chocks when using a car ramp to avoid the danger of cars slipping off the ramps. Specifications • D 2.5 cm • W 12 cm • L 50 cmFeatures & Benefits• Removable extensions create a smoother gradient for ease of access • Extensions prevent lower vehicles from being scraped on …

Min./Max. Working Height: 1225/1850mm. Capacity: 4tonne per stand. Steel stand. Pin and chain load support. Full width crutch. Designed to support part of a vehicle that is being used on a lift where free access is required. Stands also help prevent the tipping/rocking of the vehicle. These stands should not be used to support a vehicle on their own. Sold as singles, but MUST be used in pairs. Model No. ASH4000

Ideal for workshop or roadside use, these jacks take the effort out of lifting heavy plant, tractors and commercial vehicles. For extra safety, features dead man’s handle which also aids controlled lowering speed. Supplied with extensions that close the gap between the saddle of the jack and the jacking point. A comprehensive range of nine models, see logo beside each jack for main features and the table beside for detailed specification. Features & Benefits: • Max. Height (inc. extn.): 463mm @ 30 Tonne. • Air Consumption: 10.5cfm. • Spring loaded dead man's control. • Handle locks in position at three different angles. • Lifts heavy plant, tractors and commercial vehicles. • Extensions: 45…

• Approved to EU and UK Lifting Gear Regulations.• This hoist is intended for use where a suitable support facility exists.• Support brackets are included with the equipment.• N.B. Support bar is not included.Approved to EU and UK Lifting Gear Regulations. This hoist is intended for use where a suitable support facility exists. Support brackets are included with the equipment. The support bar is not included.• Approved to EU and UK Lifting Gear Regulations. • This hoist is intended for use where a suitable support facility exists. • Support brackets are included with the equipment. • Maximum Capacity (Double Cable): 250kg. • N.B. Support bar is not included. • Model No. PH250Technical Specification:Capaci…

• Low entry engine crane with a height of only 100mm at the wheels.• Weighs only 37kg so is extremely lightweight and manoeuvrable.• Heavy-duty castors and pump access from side, for safe handling of loads.• Delivered in knock-down form to reduce freight costs, some self-assembly required.Low entry engine crane with a height of only 100mm at the wheels. Weighs only 37kg so is extremely lightweight and manoeuvrable. Heavy-duty castors and pump access from side, for safe handling of loads. Delivered in knock-down form to reduce freight costs, some self-assembly required.• Low entry engine crane with a height of only 100mm at the wheels. • Weighs only 37kg so is extremely lightweight and manoeuvr…

Ideal for workshop or roadside use, this jack takes the effort out of lifting heavy plant, tractors and commercial vehicles. For extra safety, features dead man’s handle which also aids controlled lowering speed. Supplied with extensions that close the gap between the saddle of the jack and the jacking point. See table for detailed specification. Features & Benefits: • Max. Height (inc. extn.): 472mm @ 15tonne, 393mm @ 30tonne. • Air Consumption: 10.5cfm. • Spring loaded dead man's control. • Handle locks in position at three different angles. • Lifts heavy plant, tractors and commercial vehicles. • Extensions: 45, 75mm. • Model No. YAJ15-30

• Suitable for semi-permanent attachment to steel beams and acts as a lifting point for chain blocks, hoists and lifting tackle.• The clamp may also be used for lifting and transfer of steel beams and as a pulling clamp.• Low profile afforded by integral pivot/lifting point.Suitable for semi-permanent attachment to steel beams and acts as a lifting point for chain blocks, hoists and lifting tackle. The clamp may also be used for lifting and transfer of steel beams and as a pulling clamp. Low profile afforded by integral pivot/lifting point.• Suitable for semi-permanent attachment to steel beams and acts as a lifting point for chain blocks, hoists and lifting tackle. • The clamp may also be us…

• High lift jack arm ideal when lifting a light commercial vehicle.• Fitted with quick lift foot pedal.• Heavy-duty long steel chassis provides easy access to deep set jacking points.• Fitted with one-piece hydraulic unit with built-in safety overload protection.Technical SpecificationCapacity: 2000kgConsumable Parts: Optional Rubber Jacking Pad - JP06Length: 1090mmMaximum Chassis Height: 188mmMaximum Saddle Height: 800mmMinimum Saddle Height: 140mmNett Weight: 58kgTechnical Specification:Capacity: 2000kg Length: 1090mm Maximum Chassis Height: 188mm Maximum Saddle Height: 800mmDimensions: Length: 470mm x Height: 220mmWeight: 66KgWarranty: 1 year