Car Jacks

Expert Quality, polyester webbing, 150mm wide, with reinforced lifting eyes. Colour coded to European standards to identify capacity. The safe working load (SWL) is rated at 5000kg for a load at one end (straight configuration) and 10,000kg for a load between the loop eyes ('U' configuration). Shrink wrapped for security. Display packed.

• Durable 2.1kg rubber wheel chocks (1.05kg each).• Prevents car, caravan or light aircraft moving when jacking or parked on an incline.• Supplied on sturdy 550mm rope for easy storage and removal from underneath wheels.• Not intended for use on sloped ground over 10°.Durable 2.1kg rubber wheel chocks (1.05kg each). Prevents car, caravan or light aircraft moving when jacking or parked on an incline. Supplied on sturdy 550mm rope for easy storage and removal from underneath wheels. Not intended for use on sloped ground over 10°.• Durable 2.1kg rubber wheel chocks (1.05kg each). • Prevents car, caravan or light aircraft moving when jacking or parked on an incline. • Not intended for u…

Features & Benefits: • Jack Stands ideally suited to the professional trade workshop!• Manufactured from heavy duty steel• Pin type for added safety and strength• Pin wire strap secured to stand to prevent loss• Deep saddle for positive location under vehicle• Adjustable Height• Conforms to international standards CEMaterial: Heavy Duty SteelStandard: CECapacity: 1350kgMinimum Height: 255mmMaximum Height: 370mmLift Height: 110mmSaddle Diameter: 18 x 50 x 62mmBase Area: 195 x 180mm

• Approved to EU and UK Lifting Gear Regulations.• This hoist is intended for use where a suitable support facility exists.• Support brackets are included with the equipment.• N.B. Support bar is not included.Approved to EU and UK Lifting Gear Regulations. This hoist is intended for use where a suitable support facility exists. Support brackets are included with the equipment. The support bar is not included.• Approved to EU and UK Lifting Gear Regulations. • This hoist is intended for use where a suitable support facility exists. • Support brackets are included with the equipment. • Maximum Capacity (Double Cable): 250kg. • N.B. Support bar is not included. • Model No. PH250Technical Specification:Capaci…

• Heavy-duty steel-plate with rust resistant finish.• Fitted with four ø75mm metal castors, two lockable.• Each dolly features a side handle for easy carrying.• Can handle up to 250mm profiles.• Suitable for use in bodyshops and workshops.Heavy-duty steel-plate with rust resistant finish. Fitted with four ø75mm metal castors, two lockable. Each dolly features a side handle for easy carrying. Can handle up to 250mm profiles. Suitable for use in bodyshops and workshops.• Can handle up to 250mm profiles. • Fitted with four ø75mm metal castors, two lockable. • Heavy-duty steel-plate with rust resistant finish. • Each dolly features a side handle for easy carrying. • Suitable for us…

• Manufactured from 3.5mm steel section.• Suitable for professional or serious DIY applications.• Corrosion resistant finish.• Ramps stack together and will stand upright for easy storage.• BS Approved.Manufactured from 3.5mm steel section. Suitable for professional or serious DIY applications. Corrosion resistant finish. Ramps stack together and will stand upright for easy storage. BS Approved.• 2tonne Capacity per pair. • Manufactured from 3.5mm steel section. • Ramps coated with corrosion resistant finish. • Ramps stack together and will stand upright for easy storage. • Maximum Tyre Width: 200mm. • BS Approved. • Model No. CAR2000Technical Specification:Capacity Pair: 2000kgMaximum Tyre Width…

• Two composite wheel chocks.• Prevents vehicle movement when being jacked on a level surface or parked on an incline not exceeding 12°.• Suitable for cars not exceeding 2 tonne gross weight.Two composite wheel chocks. Prevents vehicle movement when being jacked on a level surface or parked on an incline not exceeding 12°. Suitable for cars not exceeding 2 tonne gross weight.• Two composite wheel chocks. • Prevents vehicle movement when being jacked on a level surface or parked on an incline not exceeding 12 degrees. • Suitable for cars not exceeding 2tonne gross weight. • Model No. WC09Technical Specification:Dimensions (W x D x H): 80 x 185 x 100mmMaterial: CompositeNett Weight: 0.44kg…

Ratchet type axle stands, with cast iron support posts. Features angled teeth in posts, which prevent accidental release of load - the more weight applied, the tighter the post is locked. Sold in pairs. Features & Benefits: • Min./Max. Working Height: 395/600mm. • Capacity: 12 Tonne per pair. • Ratchet type with cast iron support post. • Tough steel plate welded base. • Sold in pairs. • Model No. VS2006

• Adjustable outer extension clamps with rubber feet • Designed to position the engine when replacing the engine mounts. Also suitable for aiding the removal of transmission components and gearboxes • Compatible with most cars and light commercial vehicles • Supplied with one chainThis engine support beam is designed to position the engine when replacing the engine mounts. It is also suitable for aiding the removal of transmission components and gearboxes. Compatible with most cars and light commercial vehicles. Adjustable outer extension clamps with rubber feet to prevent damage to the paintwork. Supplied with one chain. 1 x ChainTechnical SpecificationAdjustable screw height: 0-305mm Capacity…

• Replacement hydraulic ram for SPC2000 engine crane.Replacement hydraulic ram for SPC2000 engine crane.• Replacement hydraulic ram for SPC2000 engine crane. • Model No. SPC2000.28Technical Specification:Nett Weight: 17.5kgRam Capacity: 8000kgRam Diameter: 37.89mmRam Travel: 624mmPump Type: Twin SpeedRam Pin Hole Diameter: 22.0mmClevis Pin Hole Diameter: 27.5mm*Mounting Point Distance (Min.): 797mm**Overall Length (Min.): 855mmBase Mount Type: Spigot Mounted * Internal diameter of spigot mount ** From base plane to ram pin centreDimensions: Length: 150mm x Height: 860mmWeight: 18KgWarranty: Consumable