Effects Pedals

Analogue modelling acoustic guitar preamp/stompbox with DI recording output that has been designed to compete head to head with leading products on the market. Its authentic tube/microphone modelling circuitry provides the natural warmth and presence, as if the acoustic guitar was miked through a tube pre-amp. It features the ultra-musical 3-band EQ with sweepable mids for accurate feedback control and to eliminate the harsh harmonics of piezo pickups; dual DI mode for either direct recording output with tube/microphone emulation or standard active direct injection box in bypass mode; and ground lift switch that eliminates typical ground loop problems. Device has super-high impedance to retain …

Compact 7-band graphic equalizer pedal with wide frequency range from 50 Hz to 10 kHz for electric bass guitar that provides total shaping control over the tone and eliminates feedback. 7 frequency bands (50, 120, 400, 500, 800 Hz; 4.5, 10 kHz) with a 15 dB of Boost/Cut provide extensive tone-shaping options, while first-class electronic on/off switch ensures noise-free operation. Pedal also features status LED for effect on/off and battery check. It can be powered by 9 V battery or 9 V adapter PSU (not included). Dimensions: 70 x 54 x 123 mm. Weight: 330 g.
Battery Operation: Yes
Тype: Equalizer
Battery Detail: Al/Mn
UK/EU Power supply included: No
Power Supply: Adapter
Made in: China…

Analog bucket-brigade delay effect pedal for guitar with up to 300 ms of delay and optionally separate wet and dry outputs that provides true analog delay experience and vintage vibe of real slap-back echo. It features advanced noise reduction circuit that keeps the signal clean, dedicated Intensity, Echo and Repeat Rate controls for amazing sound shaping, status LED for effect on/off and battery check, dual output for running the direct and delayed signals to separate rigs, and first-class electronic on/off switch that offers noise-free operation. Powered by a 9 V battery or adapter (not included). Dimensions: 70 x 54 x 123 mm. Weight: 330 g.
UK/EU Power supply included: No
Power Supply: Adapter<&hellip;

Pedal Design Foot Pedal

Overdrive and distortion pedal for electric guitar that combines the overdrive and distortion effects for a wide range of tones, suitable for use with both single-coil and humbucker pickups. It features dedicated Level, Tone, Drive and Mode controls, status LED for effect on/off and battery check, and first-class noiseless electronic on/off switch that maintains excellent signal integrity in bypass mode. Pedal is equipped with 1/4" input and output, and can be powered by 9 V battery or PSU-SB DC power supply (not included). Dimensions: 54 x 70 x 122 mm. Weight: 330 g.
Тype: Distortion;Overdrive
UK/EU Power supply included: No
Made in: China

Pedal Design Foot Pedal

Robust 7-band EQ pedal for electric and electric-acoustic guitar that shapes the sound and eliminates unwanted feedback. Pedal offers a wide frequency range – from 100 Hz to 6.4 kHz, with a powerful 15 dB boost or cut of each EQ band. It is equipped with a first-class electronic on/off switch for highest signal integrity n bypass mode, and status LED for on/off and battery check. Powered by 9 V battery or the BEHRINGER PSU-SB DC power supply (not included). Dimensions: 54 x 70 x 123 mm. Weight: 330 g.
Battery Operation: Yes
UK/EU Power supply included: No
Тype: Equalizer
Power Supply: Adapter
Made in: China

An analog modeling preamplifier and DI box designed for bass. It has a wide range of sound settings, from classic tube to sharp slap and aggressive distortion sound. In addition, it offers direct record output, V-TONE to simulate the sound of well-known vintage amplifiers and other audio options. The device can be used as a direct recording preamplifier with speaker simulation or as an active standard DI box. The effect has a built-in 6.3 mm mono jack input and output, a gold plated XLR connector and a ground lift switch. Powered by 9 V battery or DC adapter (not included).
Тype: Preamp;DI Box
Battery Detail: Al/Mn
UK/EU Power supply included: No
Made in: China

Setting up amps, dialing in tones and positioning mics takes a lot of time and patience. Step on the amazing TUBE AMP MODELER TM300 and skip straight to the good part! The TM300 features authentic modeling technology for 3 classic guitar amps, 3 gain modes and 3 mic placements for a total of 27 configurations that let you easily achieve the most sought-after tube amp sounds – from clean to crunch to super-fat distortion.
Тype: Distortion;Tube Amp Modeler;Equalizer
UK/EU Power supply included: No
Battery Operation: Yes
Power Supply: Adapter
Made in: China

Passive Cabinet Merger. The concept behind Palmer's Cab Merger may be very simple, but the unit fills an important gap! Have you ever wanted to connect two guitar cabinets to just one amplifier output? It's quite simple with the PCABM! In addition, you can choose parallel or series wiring. For instance, two 8 ohm cabinets can be connected for a total load of 4 ohms (parallel) or 16 ohms (in series). The device is entirely passive and does not affect tone in any way. Dimensions: 105 x 35 x 35 mm, weight: 0,13 kg
UK/EU Power supply included: No
Тype: DI Box
Made in: Germany

Digital stereo reverb effects pedal for electric guitar that is comparable to state-of-the-art studio processors and delivers 24-bit high-resolution stereo reverbs including Spring, Plate, Hall, Gate, Room and Modulate. It features dedicated Mode, Time, Tone and Level controls for awesome sound shaping, a status LED for effect on/off and battery check and a first-class electronic On/Off switch for signal integrity in bypass mode. Pedal runs on 9 V battery or the BEHRINGER PSU-SB DC power supply (not included). Dimensions: 54 x 70 x 123 mm. Weight: 330 g.
Made in: China
UK/EU Power supply included: No
Тype: Reverb
Power Supply: Adapter
Battery Operation: Yes
Battery Detail: Al/Mn…

Passive footswitch pedal that allows plugging a single guitar into two amplifiers or plugging two guitars into a single amplifier, making it easy and convenient to create a rig with eminent flexibility and a variety of tone options. “A or B” and “A and B” switching options allow for greater versatility, while true hardwire bypass in the off position lets players retain their natural tone without interference or signal loss. Pedal features a durable metal chassis and switches that withstand onstage wear and tear, and LED illumination (requires 9 V battery or power source). Dimensions: 127 x 83 x 51 mm.
Number of Buttons: 2
Made in: China

Bass guitar headphone amplifier from amPlug 2 series that is designed specifically for low frequencies, offering a wide-range response. It delivers three modes and features a dramatically improved analogue circuit. It also provides a rhythm function, foldable plug mechanism that rotates 180 degrees and an auto power-off function for improved convenience and ease of use. The pre-amplifier is powered by two AAA batteries (up to 11 hours of operation time, 17 with RHYTHM off), and provides a headphone output and an aux input. AAA alkaline batteries are included.
USB: No
Battery Type: AAA
Made in: Japan
Headphone Output: Yes
Battery Operation: Yes
Compressor: Yes
MP3 / Line In: Yes
Controls: Tone;Rhythm;Volume/Tempo;Volume<…

Pedal Design Foot Pedal

Afterglow Chorus is designed with the vintage aficionado in mind. Its all-analog circuit uses a Bucket Brigade Device (BBD) to create a wide range of classic handed-down modulation tones. From the smallest shudder to wildest wobble, this tiny marvel is sure to quench your thirst for vintage flavored chorus! From rotary speaker vibes to a full-blown 1980s chorus symphony, from jangle pop to grunge - Afterglow Chorus does it all. Plug in and send your tone on a journey through rock n' roll history! Many guitarists have grown to love the distinct tone of Bucket-Brigade circuits. And with good reason! The natural bandlimiting of this analog component is the secret-sauce found in countless classic …

Sound buffer that protects against signal amount and quality loss which happens with large pedalboards with many pedals and with long cables. This buffer compensates for the loss of the signal and can work at the beginning or at the end of the effect line and doesn’t need any controls. Thanks to the components being used, the amount of hum is minimum. RockBoard Natural Sound buffer is encased in a durable metal construction, houses In/Out Jack inputs and is powered by a 9V power supply, which is not included.
Power Supply: 9V DC ( - )
Made in: China
Depth (cm): 3.3
Тype: Buffer
Length (cm): 7.4
Colour: Black
True Bypass: None
UK/EU Power supply included: No
Outputs: Mono
Width (cm): 4.2
Battery Ope…

NU-X Sculpture is a mini compressor pedal with professional performance. Sustain and level controls adjust the compression and output, whilst blend gives the ability to add back in some of the unaffected signal to give a more natural attack. Hold down the on/off pedal to switch between soft clip and clean compression modes. Perfect for long sustain chords and clean lead tones. Features: Adjustable sustain and level Blend control to feed in some natural attack Selectable soft clip and clean modes Requires 9V center negative DC Power Supply 75mA current draw (Not Supplied) Specifications: Power supply: 9Vdc centre-negative power adaptor required (not included) Current consumption: 100mA Controls: …

EP-2 is a passive vol/expression pedal from Valeton Surge series, it features compact size, no need for extra battries or power adapter, you can easily control your instrument volume or some value of your effect with EP-2.While Valeton may not be a household name, the EP-2 is worth a solid look for anyone who’s just wanting a basic volume/expression pedal to get the job done. The unit, as implied by the name, pulls double duty as an expression and volume pedal; two tasks which it performs admirably.
Made in: China
Тype: Expression;Passive Design;Volume
Colour: Orange
UK/EU Power supply included: No
Controls: Expression Pedal
Battery Operation: No
Outputs: Jack 6,3mm TS
Inputs: Jack 6,3…

NU-X Morning Star is a blues drive pedal with a twist. Along with standard Drive, Level and Tone controls, holding the on/off pedal engages a Shine mode, which boosts the high frequencies adding sparkle to cut through a mix. Wide ranging gain adjustment offers tones from natural break-up to thick authentic overdrive. Enough range for blues to full-on rock styles. Features: Drive, Tone and Level controls True or buffered bypass operation Switchable Shine treble boost effect Requires 9V centre negative DC Power Supply 75mA current draw (Not Supplied) Specifications: Power supply: 9Vdc centre-negative power adaptor required (not included) Current consumption: 100mA Input impedance: 1M Ohm Output …

TailSpin Vibrato delivers a wealth of stunning vintage vibrato tones all served in a package so affordable that it'll make your head spin. Its all-analog bucket brigade design brings everything from subtle organic wobbles to pitch-bendy warped vinyl tones and all the way to fast leslie-like sounds. These beautiful tones are housed in a compact and sturdy enclosure, ready to rock the road! Nothing beats the organic warm warble of a classic true pitch vibrato pedal. You can use it at slow speeds to bring life and depth to slow chord progressions ala. Steven Wilson or you can wind it up a bit for eerie Mastodon-approved melodies or energetic Lonnie Mack solos. Heck, max it and behold the faces …

Chorus / Pedal Design Foot Pedal / Effects Chorus

The JOYO JF-323 Wooden Sound Acoustic Simulator pedal it is set to impress with its simulation of an acoustic sounding guitar. Turn your electric guitar into an acoustic one at the press of a button. With the latest mini pedal from JOYO the Wooden Sound Acoustic Simulator effect expands the range of your guitar tone without swapping out your guitar mid track, or compensating on the mix. With four controls, one each to adjust the High, Mid, Bass and Volume levels you can dial in the exact tone that you want. An amazingly nice pedal that punches above it's price range. Unlike a lot of acoustic simulator pedals this one actually sounds like you are playing an acoustic through a PA rather than just …

Switcher and signal splitter. A/B or A&B to Y mode switch, on/off footswitch, status LED (A: red, B: blue, Y: pink), 3 in-/outputs A/B/Y, 6,3 mm mono jack, optional AC adapter 9V DC (center minus plug), can be used w/o power supply (LED stays off), metal housing, dimensions (D x W x H): 93,5 mm x 42 mm x 52 mm, weight: 160 g
UK/EU Power supply included: No
Power Supply: Adapter;9V
Made in: China

Reissue series amp simulator pedal for guitar or bass. The Plexi Crunch provides a high gain distortion based on a hot-rodded British valve amplifier for classic crunch and heavy power chords. All analog circuitry ensures a pure signal path and both Tone and Presence controls closely mimic the same tone sculpting controls found on these classic amplifiers. Classic stack sounds for rock and metal guitar styles. Features: Pure analogue amplifier simulation True bypass hardware switching Preamp, Master, Tone & Presence controls Specifications: Battery: 9V PP3 (supplied) Power supply: Optional 9Vdc 300mA regulated (not supplied) Controls: Preamp, Master, Tone, Presence & foot switch Input impedance: …