Effects Pedals

Analogue modelling acoustic guitar preamp/stompbox with DI recording output that has been designed to compete head to head with leading products on the market. Its authentic tube/microphone modelling circuitry provides the natural warmth and presence, as if the acoustic guitar was miked through a tube pre-amp. It features the ultra-musical 3-band EQ with sweepable mids for accurate feedback control and to eliminate the harsh harmonics of piezo pickups; dual DI mode for either direct recording output with tube/microphone emulation or standard active direct injection box in bypass mode; and ground lift switch that eliminates typical ground loop problems. Device has super-high impedance to retain …

Pedal Design Foot Pedal

Compact 7-band graphic equalizer pedal with wide frequency range from 50 Hz to 10 kHz for electric bass guitar that provides total shaping control over the tone and eliminates feedback. 7 frequency bands (50, 120, 400, 500, 800 Hz; 4.5, 10 kHz) with a 15 dB of Boost/Cut provide extensive tone-shaping options, while first-class electronic on/off switch ensures noise-free operation. Pedal also features status LED for effect on/off and battery check. It can be powered by 9 V battery or 9 V adapter PSU (not included). Dimensions: 70 x 54 x 123 mm. Weight: 330 g.
UK/EU Power supply included: No
Battery Operation: Yes
Battery Detail: Al/Mn
Тype: Equalizer
Made in: China
Power Supply: Adapter…

Pedal Design Foot Pedal

Pedal Design Foot Pedal

Analog bucket-brigade delay effect pedal for guitar with up to 300 ms of delay and optionally separate wet and dry outputs that provides true analog delay experience and vintage vibe of real slap-back echo. It features advanced noise reduction circuit that keeps the signal clean, dedicated Intensity, Echo and Repeat Rate controls for amazing sound shaping, status LED for effect on/off and battery check, dual output for running the direct and delayed signals to separate rigs, and first-class electronic on/off switch that offers noise-free operation. Powered by a 9 V battery or adapter (not included). Dimensions: 70 x 54 x 123 mm. Weight: 330 g.
UK/EU Power supply included: No
Battery Operation: …

Pedal Design Foot Pedal

An analog modeling preamplifier and DI box designed for bass. It has a wide range of sound settings, from classic tube to sharp slap and aggressive distortion sound. In addition, it offers direct record output, V-TONE to simulate the sound of well-known vintage amplifiers and other audio options. The device can be used as a direct recording preamplifier with speaker simulation or as an active standard DI box. The effect has a built-in 6.3 mm mono jack input and output, a gold plated XLR connector and a ground lift switch. Powered by 9 V battery or DC adapter (not included).
UK/EU Power supply included: No
Battery Detail: Al/Mn
Тype: Preamp;DI Box
Made in: China

Setting up amps, dialing in tones and positioning mics takes a lot of time and patience. Step on the amazing TUBE AMP MODELER TM300 and skip straight to the good part! The TM300 features authentic modeling technology for 3 classic guitar amps, 3 gain modes and 3 mic placements for a total of 27 configurations that let you easily achieve the most sought-after tube amp sounds – from clean to crunch to super-fat distortion.
Тype: Tube Amp Modeler;Equalizer;Distortion
Made in: China
Power Supply: Adapter
Battery Operation: Yes
UK/EU Power supply included: No

Passive Cabinet Merger. The concept behind Palmer's Cab Merger may be very simple, but the unit fills an important gap! Have you ever wanted to connect two guitar cabinets to just one amplifier output? It's quite simple with the PCABM! In addition, you can choose parallel or series wiring. For instance, two 8 ohm cabinets can be connected for a total load of 4 ohms (parallel) or 16 ohms (in series). The device is entirely passive and does not affect tone in any way. Dimensions: 105 x 35 x 35 mm, weight: 0,13 kg
Made in: Germany
UK/EU Power supply included: No
Тype: DI Box

Digital stereo reverb effects pedal for electric guitar that is comparable to state-of-the-art studio processors and delivers 24-bit high-resolution stereo reverbs including Spring, Plate, Hall, Gate, Room and Modulate. It features dedicated Mode, Time, Tone and Level controls for awesome sound shaping, a status LED for effect on/off and battery check and a first-class electronic On/Off switch for signal integrity in bypass mode. Pedal runs on 9 V battery or the BEHRINGER PSU-SB DC power supply (not included). Dimensions: 54 x 70 x 123 mm. Weight: 330 g.
Тype: Reverb
Power Supply: Adapter
Made in: China
UK/EU Power supply included: No
Battery Operation: Yes
Battery Detail: Al/Mn…

Bass guitar headphone amplifier from amPlug 2 series that is designed specifically for low frequencies, offering a wide-range response. It delivers three modes and features a dramatically improved analogue circuit. It also provides a rhythm function, foldable plug mechanism that rotates 180 degrees and an auto power-off function for improved convenience and ease of use. The pre-amplifier is powered by two AAA batteries (up to 11 hours of operation time, 17 with RHYTHM off), and provides a headphone output and an aux input. AAA alkaline batteries are included.
Battery Type: AAA
Power Supply: None, Only Battery Operated
Offer Configuration: Standard offer
Controls: Volume;Volume/Tempo;Rhythm;Tone<…

Pedal Design Foot Pedal / Operation analogue

Compressor

Volume Pedal

Wah-Wah

Pedal Design Foot Pedal / Operation analogue

NU-X Morning Star is a blues drive pedal with a twist. Along with standard Drive, Level and Tone controls, holding the on/off pedal engages a Shine mode, which boosts the high frequencies adding sparkle to cut through a mix. Wide ranging gain adjustment offers tones from natural break-up to thick authentic overdrive. Enough range for blues to full-on rock styles. Features: Drive, Tone and Level controls True or buffered bypass operation Switchable Shine treble boost effect Requires 9V centre negative DC Power Supply 75mA current draw (Not Supplied) Specifications: Power supply: 9Vdc centre-negative power adaptor required (not included) Current consumption: 100mA Input impedance: 1M Ohm Output …

Chorus / Pedal Design Foot Pedal / Effects Chorus

The JOYO JF-323 Wooden Sound Acoustic Simulator pedal it is set to impress with its simulation of an acoustic sounding guitar. Turn your electric guitar into an acoustic one at the press of a button. With the latest mini pedal from JOYO the Wooden Sound Acoustic Simulator effect expands the range of your guitar tone without swapping out your guitar mid track, or compensating on the mix. With four controls, one each to adjust the High, Mid, Bass and Volume levels you can dial in the exact tone that you want. An amazingly nice pedal that punches above it's price range. Unlike a lot of acoustic simulator pedals this one actually sounds like you are playing an acoustic through a PA rather than just …

Reissue series amp simulator pedal for guitar or bass. The Plexi Crunch provides a high gain distortion based on a hot-rodded British valve amplifier for classic crunch and heavy power chords. All analog circuitry ensures a pure signal path and both Tone and Presence controls closely mimic the same tone sculpting controls found on these classic amplifiers. Classic stack sounds for rock and metal guitar styles. Features: Pure analogue amplifier simulation True bypass hardware switching Preamp, Master, Tone & Presence controls Specifications: Battery: 9V PP3 (supplied) Power supply: Optional 9Vdc 300mA regulated (not supplied) Controls: Preamp, Master, Tone, Presence & foot switch Input impedance: …

Switcher and signal splitter. A/B or A&B to Y mode switch, on/off footswitch, status LED (A: red, B: blue, Y: pink), 3 in-/outputs A/B/Y, 6,3 mm mono jack, optional AC adapter 9V DC (center minus plug), can be used w/o power supply (LED stays off), metal housing, dimensions (D x W x H): 93,5 mm x 42 mm x 52 mm, weight: 160 g
UK/EU Power supply included: No
Power Supply: 9V;Adapter
Made in: China

Flanger / Pedal Design Foot Pedal / Effects Flanger

The signal-pollution from the decadent, noise-producing effect pedals is not welcome behind the iron curtain! Iron Curtain is a classic, simple no-nonsense noise gate with intuitive controls, high quality components and zero tolerance for any unwanted noise in your signal - only the purest tone is welcome in the noise-free republic! Some old amplifiers or some venues just have a lot inherent noise. If the dynamics of your playing is important to you, going from a soft touch with barely audible notes and up to blasting the roof off, a good noise gate can help you keep that sonic image sharp and crisp. Iron Curtain is built on a classic all-analog circuit that will keep out any unwanted noise …