Car Jacks

• Jacking beam lifts load with compressed air.• Fully certified and approved to comply with MOT requirements.• Features 2-stage mechanical safety lock and telescopic finger guards to prevent accidental injury.• Supplied with two pairs of aluminium support blocks.• Beam has spring loaded flat arms with roller bearings - when unloaded, these support the weight of the beam, allowing the entire unit to run smoothly along the pit or ramp, but when loaded, they firmly stabilise the unit.• Optional hook arms supplied.• Wide lift configuration meets MOT recommendation for lifting on jacking point.• This item is heavy. Extra assistance must be provided at the delivery point to help its safe delivery.Ja…

Ideal for workshop or roadside use, this jack takes the effort out of lifting heavy plant, tractors and commercial vehicles. For extra safety, features dead man’s handle which also aids controlled lowering speed. Supplied with extensions that close the gap between the saddle of the jack and the jacking point. See table for detailed specification. Features & Benefits: • Max. Height (inc. extn.): 472mm @ 15tonne, 393mm @ 30tonne. • Air Consumption: 10.5cfm. • Spring loaded dead man's control. • Handle locks in position at three different angles. • Lifts heavy plant, tractors and commercial vehicles. • Extensions: 45, 75mm. • Model No. YAJ15-30

Faithfull Lifting Slings are made from 100% PES polyester duplex webbing that is lightweight but extremely durable for use on awkward loads, offering a soft alternative to wires and chains. All sizes can be used in straight pull, basket or choke configurations. Fitted with a reinforced, sleeved lifting eye. Meets the requirements of EN 1492 Part 1:2000. Minimum breaking load is 7 times the Working Load Limit.The Faithfull Green Lifting Sling has the following specifications: Max. Load: 2 Tonne.Width: 60mm.Length: 2m.Additional Information:• Length: 2.0m• Type: Lifting Sling• Load Capacity: 2000kg• Breaking Strength: 14000kg

Textured rubber provides high amount of grip while remaining soft, to prevent damage to the car underbody. Slot in the support block allows the car to be lifted by the sill. Manufactured from zinc plated steel and rubber, providing a sturdy and durable point of contact. Suitable for use with Sealey Viking 2 & 3 Tonne Jacking Beams. Used in conjunction with Model No's SJBEX.A06 or SJBEX.A07 Jacking Beam Extensions.Features & Benefits:• Textured rubber provides high amount of grip while remaining soft, to prevent damage to the car underbody.• Slot in the support block allows the car to be lifted by the sill.• Manufactured from zinc plated steel and rubber, providing a sturdy and durable point …

• Suitable for lower capacity single and twin cylinder engines.• Supports can rotate for accessibility to all parts of the engine.• Useful integral utility/drip tray.• Capacity: 30kg.Suitable for small capacity single and twin cylinder engines (maximum weight 30kg) and includes a utility/drip tray. Supports can rotate for accessibility to all parts of the engine.• Suitable for lower capacity single and twin cylinder engines. • Supports can rotate for accessibility to all parts of the engine. • Useful integral utility/drip tray. • Capacity: 30kg. • Model No. MES01Technical Specification:Capacity: 30kgEngine Support Span: 200-370mmHeight: 375mmLength: 535mmNett Weight: 7.89kgWidth: 320mmDimensions: L…

Single-piece hydraulic unit with heavy base design. Integral cog-type release mechanism and long 2-piece handle. Protective jack handle sleeve helps prevent accidental damage to car bodywork when pumping the handle. Heavy-duty castors and extra-large saddle design ease positioning under vehicle. Fitted with safety overload valve and pump-through valve to prevent handle locking at maximum ram extension. Ideal for loaded vans up to 3.5 Tonne GVW. Features & Benefits: • Min./Max. Saddle Height: 130/520mm. • Chassis Length: 659mm. • Integral cog-type release mechanism and long 2-piece handle. • Heavy-duty swivel castors and extra-large saddle design ease positioning under vehicle. • Fitted with safet…

• Replacement hydraulic ram for SC10LR.V3 engine crane.Technical SpecificationNett Weight: 11kgRam Capacity: 7257kgRam Diameter: 30mmRam Travel: 480mmPump Type: Single SpeedRam Pin Hole Diameter: 16.5mmClevis Pin Hole Diameter: 16.5mmMounting Point Distance (Min): 650mmOverall Length (Min): 665mmBase mount Type: Double ClevisTechnical Specification:Capacity: 7257kg Diameter: 30mmDimensions: Length: 710mm x Height: 150mmWeight: 9.99KgWarranty: 1 year

Ideal for workshop or roadside use, these jacks take the effort out of lifting heavy plant, tractors and commercial vehicles. For extra safety, features dead man’s handle which also aids controlled lowering speed. Supplied with extensions that close the gap between the saddle of the jack and the jacking point. A comprehensive range of nine models, see logo beside each jack for main features and the table beside for detailed specification. Features & Benefits: • Max. Height (inc. extn.): 463mm @ 30 Tonne. • Air Consumption: 10.5cfm. • Spring loaded dead man's control. • Handle locks in position at three different angles. • Lifts heavy plant, tractors and commercial vehicles. • Extensions: 45…

• Suitable for semi-permanent attachment to steel beams and acts as a lifting point for chain blocks, hoists and lifting tackle.• The clamp may also be used for lifting and transfer of steel beams and as a pulling clamp.• Low profile afforded by integral pivot/lifting point.Suitable for semi-permanent attachment to steel beams and acts as a lifting point for chain blocks, hoists and lifting tackle. The clamp may also be used for lifting and transfer of steel beams and as a pulling clamp. Low profile afforded by integral pivot/lifting point.• Suitable for semi-permanent attachment to steel beams and acts as a lifting point for chain blocks, hoists and lifting tackle. • The clamp may also be us…