Car Jacks

• Adjustable outer extension clamps with rubber feet • Designed to position the engine when replacing the engine mounts. Also suitable for aiding the removal of transmission components and gearboxes • Compatible with most cars and light commercial vehicles • Supplied with two chainsThis engine support beam is designed to position the engine when replacing the engine mounts. It is also suitable for aiding the removal of transmission components and gearboxes. Compatible with most cars and light commercial vehicles. Adjustable outer extension clamps with rubber feet to prevent damage to the paintwork. Supplied with two chains. 2 x ChainsTechnical SpecificationAdjustable screw height: 0-205mm Capacity…

• Replacement hydraulic ram for SPC1000 engine crane.Replacement hydraulic ram for SPC1000 engine crane.• Replacement hydraulic ram for SPC1000 engine crane. • Model No. SPC1000.28Technical Specification:Nett Weight: 13kgRam Capacity: 5000kgRam Diameter: 31.92mmRam Travel: 585mmPump Type: Twin SpeedRam Pin Hole Diameter: 18.0mmClevis Pin Hole Diameter: 27.5mm*Mounting Point Distance (Min.): 706mm**Overall Length (Min): 763mmBase Mount Type: Spigot Mounted * Internal diameter of spigot mount ** From base plane to ram pin centreDimensions: Length: 100mm x Height: 110mmWeight: 12.972KgWarranty: Consumable

Expert Quality, polyester webbing, 50mm wide, with reinforced lifting eyes. Colour coded to European standards to identify capacity. The safe working load (SWL) is rated at 1000kg for a load at one end (straight configuration) and 2000kg for a load between the loop eyes ('U' configuration). Shrink wrapped for security. Display packed.

• Designed to prevent damage to the underside of the vehicle's jacking point.• Type A design.• Fits over the jack saddle.Designed to prevent damage to the underside of the vehicle's jacking point. Design Type A. Profile Depth 27mm. Size 118.5mm Square. Fits saddle ø100-106mm.• Designed to prevent damage to the underside of the vehicle's jacking point. • Design Type A. • Profile Depth: 27mm. • Size: 118.5mm Square. • Fits saddle ø100-106mm. • Model No. JP01Technical Specification:Nett Weight: 0.18kgJack Pad Size: 118.5mm (Square)Style: Type AProfile Depth: 27mmTo Fit Saddle Size: ø100-106mmWeight: 0.18kgDimensions: Length: 30mm x Height: 190mmWeight: 0.196KgWarranty: Consumable

• A fully adjustable saddle with forward, backward and side-to-side tilt.• Note: When using these adjustable supports the maximum capacity of the jack and support combination will be limited to the lowest specified capacity in the combination. e.g. 600GA and ADT3 - Maximum capacity is 500kg.Fully adjustable saddle with forward, backward and side-to-side tilt. Suitable for Model No's. 300TR, 300TRQ, 600TR, 600TRQ.• A fully adjustable saddle with forward, backward and side-to-side tilt. • Suitable for Model No's. 300TR, 300TRQ, 600TR, 600TRQ. • Note: When using these adjustable supports the maximum capacity of the jack and support combination will be limited to the lowest specified capacity in the com…

Texspan round slings are manufactured from 100% polyester. The sling is made up with a seamless outer polyester cover and a core produced from a continuous hank of high-tenacity polyester. They are softer than duplex slings and kinder to delicate surfaces. BS EN1492: 2000 compliant. NB Length quoted are for the effective working length, which is half the circumference of the sling . A full range of effective working lengths is also available from 0.5m to 6m and strength ratings in excess of 2 tonnes up to a maximum of 6 tonnes. Working Load Limit: 2 tonne x 1 metre

• Telescopic hydraulic ram allows a reduced closed height without compromising maximum lift height.• Made in the EU and fitted with safety overload valve.• One-piece steel base, reservoir and pump cylinder design gives added strength.• Supplied with zinc coated handle.Telescopic hydraulic ram allows a reduced closed height without compromising maximum lift height. Made in the EU and fitted with safety overload valve. One-piece steel base, reservoir and pump cylinder design gives added strength. Supplied with zinc coated handle.• Min./Max. Height: 145/360mm. • Telescopic hydraulic ram allows a reduced closed height without compromising maximum lift height. • Made in the EU and fitted with safety ov…

Expert Quality, polyester webbing, 150mm wide, with reinforced lifting eyes. Colour coded to European standards to identify capacity. The safe working load (SWL) is rated at 5000kg for a load at one end (straight configuration) and 10,000kg for a load between the loop eyes ('U' configuration). Shrink wrapped for security. Display packed.

• Designed to prevent damage to the underside of the vehicle's jacking point.• Type B design.• Fits inside the jack saddle.Designed to prevent damage to the underside of the vehicle's jacking point. Design Type B. Profile Height 8.3mm. Size ø99.5mm. Fits saddle ø99-103mm.• Designed to prevent damage to the underside of the vehicle's jacking point. • Design Type B. • Profile Height: 8.3mm. • Size: ø99.5mm. • Fits saddle ø99-103mm. • Model No. JP16Technical Specification:Nett Weight: 0.075kgJack Pad Size: ø99.5mmStyle: Type BProfile Depth: 8.3mmTo Fit Saddle Size: ø99-103mmWeight: 0.075kgDimensions: Length: 10mm x Height: 190mmWeight: 0.074KgWarranty: Consumable

Base and reservoir machine welded for increased strength and reduced chance of leakage. Fitted with overload valve. Supplied with 3-piece handle. Fitted with carrying handle. Features & Benefits: • Min./Max. Height: 260/420mm. • Fitted with overload valve. • Base and reservoir machine welded. • Supplied with 3-piece handle. • Fitted with carrying handle. • Model No. SJ30 Specifications: Model No SJ30 Brand: Sealey Capacity: 30 Tonne Hydraulic Lift: 160mm Maximum Height: 420mm Minimum Height: 260mm Nett Weight: 17.8kg Screw Extension: n/a

• Triple castor wheel design allows a stabile multi-directional movement of motorcycle once lifted.• Features width adjustment from 185 to 265mm, making it suitable for most types of motorcycle. • Design ensures rim and tyre protection at all times.• Once the bike is supported, allows easy removal and cleaning of front wheel.• Please note: All front paddock stands need to be used in conjunction with a suitable rear stand to ensure bike stability (See Model No's RPS2 or, for full floating movement, use RPS2MD).Technical SpecificationNett Weight: 6.4kg