Car Jacks

All steel stand with pin and chain load support and full width crutches for safe support of load. Designed to support part of a vehicle that is being used on a lift where free access is required. Stan more→ds also help prevent the tipping/rocking of the vehicle. Note: These stands should not be used to support a vehicle on their own. Sold as singles, but MUST be used in pairs. Features & Benefits: • Min./Max. Working Height: 1225/1850mm. • Capacity: 4tonne per stand. • Steel stand. • Pin and chain load support. • Full width crutch. • Designed to support part of a vehicle that is being used on a lift where free access is required. • Stands also help prevent the tipping/rocking of the vehicle. • The…

Ideal for workshop or roadside use, these jacks take the effort out of lifting heavy plant, tractors and commercial vehicles. For extra safety, features dead man’s handle which also aids controlled lo more→wering speed. Supplied with extensions that close the gap between the saddle of the jack and the jacking point. A comprehensive range of nine models, see logo beside each jack for main features and the table beside for detailed specification. Features & Benefits: • Max. Height (inc. extn.): 463mm @ 30 Tonne. • Air Consumption: 10.5cfm. • Spring loaded dead man's control. • Handle locks in position at three different angles. • Lifts heavy plant, tractors and commercial vehicles. • Extensions: 45…

• Approved to EU and UK Lifting Gear Regulations.• This hoist is intended for use where a suitable support facility exists.• Support brackets are included with the equipment.• N.B. Support bar is not more→included.Approved to EU and UK Lifting Gear Regulations. This hoist is intended for use where a suitable support facility exists. Support brackets are included with the equipment. The support bar is not included.• Approved to EU and UK Lifting Gear Regulations. • This hoist is intended for use where a suitable support facility exists. • Support brackets are included with the equipment. • Maximum Capacity (Double Cable): 250kg. • N.B. Support bar is not included. • Model No. PH250Technical Specification:Capaci…

Features & Benefits: • Jack Stands ideally suited to the professional trade workshop!• Manufactured from heavy duty steel• Pin type for added safety and strength• Pin wire strap se more→cured to stand to prevent loss• Deep saddle for positive location under vehicle• Adjustable Height• Conforms to international standards CEMaterial: Heavy Duty SteelStandard: CECapacity: 1350kgMinimum Height: 255mmMaximum Height: 370mmLift Height: 110mmSaddle Diameter: 18 x 50 x 62mmBase Area: 195 x 180mm

• Low entry engine crane with a height of only 100mm at the wheels.• Weighs only 37kg so is extremely lightweight and manoeuvrable.• Heavy-duty castors and pump access from side, for safe handling of more→loads.• Delivered in knock-down form to reduce freight costs, some self-assembly required.Low entry engine crane with a height of only 100mm at the wheels. Weighs only 37kg so is extremely lightweight and manoeuvrable. Heavy-duty castors and pump access from side, for safe handling of loads. Delivered in knock-down form to reduce freight costs, some self-assembly required.• Low entry engine crane with a height of only 100mm at the wheels. • Weighs only 37kg so is extremely lightweight and manoeuvr…

Ideal for workshop or roadside use, this jack takes the effort out of lifting heavy plant, tractors and commercial vehicles. For extra safety, features dead man’s handle which also aids controlled low more→ering speed. Supplied with extensions that close the gap between the saddle of the jack and the jacking point. See table for detailed specification. Features & Benefits: • Max. Height (inc. extn.): 472mm @ 15tonne, 393mm @ 30tonne. • Air Consumption: 10.5cfm. • Spring loaded dead man's control. • Handle locks in position at three different angles. • Lifts heavy plant, tractors and commercial vehicles. • Extensions: 45, 75mm. • Model No. YAJ15-30

• Suitable for semi-permanent attachment to steel beams and acts as a lifting point for chain blocks, hoists and lifting tackle.• The clamp may also be used for lifting and transfer of steel beams and more→as a pulling clamp.• Low profile afforded by integral pivot/lifting point.Suitable for semi-permanent attachment to steel beams and acts as a lifting point for chain blocks, hoists and lifting tackle. The clamp may also be used for lifting and transfer of steel beams and as a pulling clamp. Low profile afforded by integral pivot/lifting point.• Suitable for semi-permanent attachment to steel beams and acts as a lifting point for chain blocks, hoists and lifting tackle. • The clamp may also be us…

• High lift jack arm ideal when lifting a light commercial vehicle.• Fitted with quick lift foot pedal.• Heavy-duty long steel chassis provides easy access to deep set jacking points.• Fitted with one more→-piece hydraulic unit with built-in safety overload protection.Technical SpecificationCapacity: 2000kgConsumable Parts: Optional Rubber Jacking Pad - JP06Length: 1090mmMaximum Chassis Height: 188mmMaximum Saddle Height: 800mmMinimum Saddle Height: 140mmNett Weight: 58kgTechnical Specification:Capacity: 2000kg Length: 1090mm Maximum Chassis Height: 188mm Maximum Saddle Height: 800mmDimensions: Length: 470mm x Height: 220mmWeight: 66KgWarranty: 1 year

• Telescopic hydraulic ram allows a reduced closed height without compromising maximum lift height.• Made in the EU and fitted with safety overload valve.• One-piece steel base, reservoir and pump cyl more→inder design gives added strength.• Supplied with zinc coated handle.Telescopic hydraulic ram allows a reduced closed height without compromising maximum lift height. Made in the EU and fitted with safety overload valve. One-piece steel base, reservoir and pump cylinder design gives added strength. Supplied with zinc coated handle.• Min./Max. Height: 145/360mm. • Telescopic hydraulic ram allows a reduced closed height without compromising maximum lift height. • Made in the EU and fitted with safety ov…

Ratchet type axle stands with cast iron support posts. Angled teeth in post prevent accidental release of load - the more weight applied, the tighter the post is locked. Sold in pairs. Features & Ben more→efits: • Min./Max. Working Height: 285/420mm. • Capacity: 6 Tonne per pair. • Ratchet type with cast iron support posts. • Tough steel-plate welded bases. • Sold in pairs. • Model No. VS2003