Car Jacks

Expert Quality, ideal for the workshop or factory use. The chain hoist has a triple spur geared shaft and pinion with load braking and double pawls. The compact gear housing allows use in areas of lim more→ited clearance. High quality welded chain with safety latches on the load hooks.

Expert Quality, ideal for the workshop or factory use. The chain hoist has a triple spur geared shaft and pinion with load braking and double pawls. The compact gear housing allows use in areas of lim more→ited clearance. High quality welded chain with safety latches on the load hooks.

• IDEAL FOR 4x4 VEHICLES - Clever device which quickly and safely overcomes the awkward job of lifting 4x4 vehicles with offset differentials.• EASY-TO-USE - Simply remove the existing trolley jack sa more→ddle, replace with cross beam adaptor, fit the jack saddle into the hole in the adaptor (30mm spigot pin) and you are ready to lift.• SIZE - Minimum/Maximum Height: 140/230mm.• SUITABLE FOR - Jacks with a 31-33mm saddle spigot pin, including Model No's 3000CXD and 3010CX.*Note: Remove any rubber jack pad from the saddle before using to improve safety.Quickly and safely overcomes the awkward job of lifting 4x4 vehicles with offset differentials. Simply remove the existing trolley jack saddle, replace…

• EXTRA SAFETY - Provides extra safety when locating awkward jacking point.• SUITABLE FOR - Ideal for front wheel drive vehicles. Suitable for jacks with a 31-33mm saddle spigot pin.Provides extra saf more→ety when locating awkward jacking point. Ideal for front wheel drive vehicles. Suitable for jacks with a 31-33mm saddle spigot pin.• Provides extra safety when locating awkward jacking point. • Ideal for front wheel drive vehicles. Suitable for jacks with a 31-33mm saddle spigot pin. • Model No. X136Technical Specification:Application(s): 3000CXD, 3010CXMaximum Width: 820mmMinimum Width: 580mmNett Weight: 12.90kgScrew Adjustment: 75mmDimensions: Length: 170mm x Height: 142mmWeight: 12.1KgWarrant…

• Two composite wheel chocks.• Prevents vehicle movement when being jacked on a level surface or parked on an incline not exceeding 12°.• Suitable for cars not exceeding 2 tonne gross weight.Two more→composite wheel chocks. Prevents vehicle movement when being jacked on a level surface or parked on an incline not exceeding 12°. Suitable for cars not exceeding 2 tonne gross weight.• Two composite wheel chocks. • Prevents vehicle movement when being jacked on a level surface or parked on an incline not exceeding 12 degrees. • Suitable for cars not exceeding 2tonne gross weight. • Model No. WC09Technical Specification:Dimensions (W x D x H): 80 x 185 x 100mmMaterial: CompositeNett Weight: 0.44kg…

Perfect for garage use, or for the home motor enthusiast, these durably constructed car ramps can be used together to lift vehicles of 2000kg or less to provide access for maintenance purposes. They c more→an also be used to gain the clearance needed to insert a bottle jack. The solid frames of the ramps are fitted with rungs to prevent slippage of the wheel after the car has been raised, & an extended rear face allows the car ramps to be stood upright for convenient, space saving storage. For low ground clearance vehicles, an extension is available for purchase separately (part number: RM1). Specifications: • Capacity per Pair: 2000kg • Length: 790mm • Car Ramp Height: 250mm • …

Designed for use with the CR2 Car Ramp Extension Set (part number: TUPCR2), this pair of car ramp extensions fits onto the base of the ramps to provide a more gradual gradient for raising low ground c more→learance vehicles. It will prove invaluable if working with many types of sports car or custom vehicle. The Car Ramps are NOT included, & are available for purchase separately. Important Always use wheel chocks when using a car ramp to avoid the danger of cars slipping off the ramps. Specifications • D 2.5 cm • W 12 cm • L 50 cmFeatures & Benefits• Removable extensions create a smoother gradient for ease of access • Extensions prevent lower vehicles from being scraped on …

Perfect for garage use or for the home motor enthusiast, these durably constructed car ramps can be used together to lift vehicles of 2000kg or less to provide access for maintenance purposes. They ca more→n also be used to gain the clearance needed to insert a bottle jack. The solid frames of the car ramps are fitted with rungs to prevent slippage of the wheel after the car has been raised, & an extended rear face allows the ramps to be stood upright for convenient, space saving storage. For ease of use, and especially when working with low ground clearance vehicles like sports cars and custom builds, this set is also supplied with a matching pair of removable car ramp extensions. These fit onto …

• Made from durable polypropylene.• These ramps are designed to allow jacking access to suitable jacking points on the vehicle.• Not intended to raise a vehicle enough for under vehicle servicing.Made more→from durable polypropylene. These ramps are designed to allow jacking access to suitable jacking points on the vehicle. Not intended to raise a vehicle enough for under vehicle servicing.• 3tonne Capacity per pair. • Made from durable polypropylene. • These ramps are designed to allow jacking access to suitable jacking points on the vehicle. • Not intended to raise a vehicle enough for under vehicle servicing. • Overall Dimensions (L x W x H): 700 x 200 x 80mm. • Model No. CAR3000LRTechnical Specification:Capa…

• Manufactured from durable polypropylene.• Suitable for professional or serious DIY applications.Manufactured from durable polypropylene. Suitable for professional or serious DIY applications.• 3tonn more→e Capacity per pair. • Manufactured from durable polypropylene. • Suitable for professional or serious DIY applications. • Overall Dimensions (L x W x H): 900 x 300 x 215mm. • Maximum Tyre Width: 260mm. • Model No. CAR3000CTechnical Specification:Capacity Pair: 3000kgMaximum Tyre Width: 260mmNett Weight: 0.00kgOverall Dimensions (L x W x H): 900 x 300 x 215mmRamp Height: 160mmDimensions: Length: 330mm x Height: 315mmWeight: 9.76KgWarranty: 1 year

• Steel construction car ramp extensions to decrease ascent angle.• Ideal for cars with low ground clearance.• Attaches to standard car ramps with a minimum width of 195mm.• Suitable for use with Mode more→l No. CAR2000.Steel construction car ramp extensions to decrease ascent angle. Ideal for sports cars and vehicles with low ground clearance. Attaches to standard car ramps with a minimum width of 195mm. Suitable for use with Model No. CAR2000.• Steel construction car ramp extensions to decrease ascent angle. • Ideal for cars with low ground clearance. • Attaches to standard car ramps with a minimum width of 195mm. • Suitable for use with Model No. CAR2000. • Length: 630mm. • Capacity: 400kg Each…

• Manufactured from 3.5mm steel section.• Suitable for professional or serious DIY applications.• Corrosion resistant finish.• Ramps stack together and will stand upright for easy storage.• BS Approve more→d.Manufactured from 3.5mm steel section. Suitable for professional or serious DIY applications. Corrosion resistant finish. Ramps stack together and will stand upright for easy storage. BS Approved.• 2tonne Capacity per pair. • Manufactured from 3.5mm steel section. • Ramps coated with corrosion resistant finish. • Ramps stack together and will stand upright for easy storage. • Maximum Tyre Width: 200mm. • BS Approved. • Model No. CAR2000Technical Specification:Capacity Pair: 2000kgMaximum Tyre Width…

• Suitable for semi-permanent attachment to steel beams and acts as a lifting point for chain blocks, hoists and lifting tackle.• The clamp may also be used for lifting and transfer of steel beams and more→as a pulling clamp.• Low profile afforded by integral pivot/lifting point.Suitable for semi-permanent attachment to steel beams and acts as a lifting point for chain blocks, hoists and lifting tackle. The clamp may also be used for lifting and transfer of steel beams and as a pulling clamp. Low profile afforded by integral pivot/lifting point.• Suitable for semi-permanent attachment to steel beams and acts as a lifting point for chain blocks, hoists and lifting tackle. • The clamp may also be us…

• Suitable for semi-permanent attachment to steel beams and acts as a lifting point for chain blocks, hoists and lifting tackle.• The clamp may also be used for lifting and transfer of steel beams and more→as a pulling clamp.• Low profile afforded by integral pivot/lifting point.Suitable for semi-permanent attachment to steel beams and acts as a lifting point for chain blocks, hoists and lifting tackle. The clamp may also be used for lifting and transfer of steel beams and as a pulling clamp. Low profile afforded by integral pivot/lifting point.• Suitable for semi-permanent attachment to steel beams and acts as a lifting point for chain blocks, hoists and lifting tackle. • The clamp may also be us…

• Heavy-duty 7 Tonne short axle stands.• Sturdy welded steel construction for superior safety and strength.• Large crutch for good load distribution.• Supplied with captive pin load support.• Suitable more→for use with forklifts and vehicles with low suspension.• Sold in pairs.Heavy-duty short axle stands. Sturdy welded steel construction for superior safety and strength. Large crutch for good load distribution. Supplied with captive pin load support. Suitable for use with forklifts and vehicles with low suspension. Sold in pairs.• Min./Max. Working Height: 244/354mm. • Capacity: 14tonne per pair. • Sturdy welded steel construction. • Captive pin load support. • For forklifts and vehicles with low …

• Heavy-duty 6 Tonne axle stands.• Sturdy welded steel construction for superior safety and strength.• Supplied with captive pin load support.• Range available in five different colours.• Sold in pair more→s.• 2 Year guarantee*.Heavy-duty axle stands to safely support vehicles for extended periods of time. Large crutches for good load distribution. The heavy gauge steel frame and welded construction gives superior strength and safety. All stands feature captive, multi-position pin load support. Sold in pairs.• Min./Max. Working Height: 369/571mm. • Capacity: 12tonne per pair. • Sturdy welded steel construction. • Captive pin load support. • Range available in five different colours. • Sold in pairs. • 2 …

Ideal for workshop or roadside use, these jacks take the effort out of lifting heavy plant, tractors and commercial vehicles. For extra safety, features dead man’s handle which also aids controlled lo more→wering speed. Supplied with extensions that close the gap between the saddle of the jack and the jacking point. A comprehensive range of nine models, see logo beside each jack for main features and the table beside for detailed specification. Features & Benefits: • Max. Height (inc. extn.): 463mm @ 30 Tonne. • Air Consumption: 10.5cfm. • Spring loaded dead man's control. • Handle locks in position at three different angles. • Lifts heavy plant, tractors and commercial vehicles. • Extensions: 45…

• A fully adjustable saddle with forward, backward and side-to-side tilt.• Suitable for use with Model No's. 500TTJ and 800TTJ.Fully adjustable saddle with forward, backward and side-to-side tilt. Sui more→table for use with Model No's. 500TTJ and 800TTJ.• A fully adjustable saddle with forward, backward and side-to-side tilt. • Suitable for use with Model No's. 1000ETJ, 1000TR, 1000TRQ, 1500TR. • Model No. ADT5Technical Specification:Capacity: 1000kgCompatibility: 500TTJ and 800TTJ.Nett Weight: 23.69kgDimensions: Length: 315mm x Height: 350mmWeight: 24.6KgWarranty: 1 year

Specifications:- Weight: 2,578kg- Ability: 1500kg- Application: Automotive- Plastic weight: 6g

Single-piece hydraulic unit with heavy base design. Integral cog-type release mechanism and long 2-piece handle. Protective jack handle sleeve helps prevent accidental damage to car bodywork when pump more→ing the handle. Heavy-duty castors and extra-large saddle design ease positioning under vehicle. Fitted with safety overload valve and pump-through valve to prevent handle locking at maximum ram extension. Ideal for loaded vans up to 3.5 Tonne GVW. Features & Benefits: • Min./Max. Saddle Height: 130/520mm. • Chassis Length: 659mm. • Integral cog-type release mechanism and long 2-piece handle. • Heavy-duty swivel castors and extra-large saddle design ease positioning under vehicle. • Fitted with safet…

• Package Includes:• 3000CXD - Trolley Jack 3tonne Standard Chassis• AS3 - Axle Stands (Pair) 3tonne Capacity per Stand - White• You may also refer to the individual Model No. for full specification.P more→ackage Includes:3000CXD - 3tonne Trolley JackAS3 - Axle Stands (Pair) 3tonne Capacity per Stand - WhiteTechnical Specification:Trolley Jack: 3000CXDLength: 659mmMinimum Saddle Height: 130mmMaximum Saddle Height: 520mmMaximum Chassis Height: 172mmAxles Stands (Pair): AS3 - 3tonneWeight: 44.57KgWarranty: 1 year

The Master Lock Carry Strap No. 3126EURDAT features a 2.5m long x 25mm and 5.5m long x 25mm crossed straps with zamac buckles. They are a readymade carrying solution with a strap and an integrated han more→dle.They are ideal to carry cartons or pieces of furniture, the metal cam buckle enables you to adjust the length of the strap. The two handles with foam finish make the use even more comfortable. Colour: Red.Strap Width: 25mm. Additional Information:• Length: 2.5 & 5.5m• Type: Carry Strap• Load Capacity: 80kg

• Weight-for-weight, this strap is three to five times stronger than chain and has the advantage that overload can be detected early by the fraying of the strap.• Manufactured from 100% high strength more→polyester with reinforced lifting eyes.• Colour-coded according to European standards for identifying capacity.• Safe working load ratings quoted are for a load between the loop eyes (U configuration) and a load at one end (straight configuration).Weight-for-weight, this strap is three to five times stronger than chains and have the advantage that overload can be detected early by the fraying of the straps. Manufactured from 100% high strength polyester with reinforced lifting eyes. Colour-coded accordin…

For repairs and maintenance. Suitable for most standard cars. Platform height 200mm; platform width 205mm approx. Extensions are available to lower the angle for low ground clearance vehicles Stock No more→23306. Sold loose.