Diving Accessories

Precision machined from 316L stainless steel.Protects 200 and 300 bar DIN threads.Seals water out with Viton o-ring for oxygen compatibility.No groove through threads.

Make any primary regulator more comfortable while diving.Routes the hose under the right arm instead of over the shoulder.Often used on octopus to improve hose routing.Installs between the second stage and the regulator hose.Chromed brass construction.Usable up to 40% oxygen.Choose the pefect angle between 0° and 350° by simply twisting the adapter!.

LP Hose Splitter AC918 - Attach to the second stage end of one low pressure regulator hose - Allows the attachment of two low pressure regulator hoses (first stage ends) - One 9/16-18 male inlet to two 3/8-24 female outlets - Chromed brass construction - Low pressure only - below 200 psi

Features:- Fits over wetsuit of drysuit - Advanced bike shorts pattern - 2mm super-stretch neoprene - black - Durable flat-lock seams - Nylon cord draw string to prevent slipping - Two Tech Thigh Pockets.

Features:- Velcro release weight dump - pull out, then down- Designed to add up to 5 lbs. of bagged shot or hard weight - Attaches by sliding over the end of any 2 webbing - Easy addition to XS Scuba weight belt or other harness systems- Perfect for adjusting your trim

Same design as Single Weight Pocket above, except:- Allows pocket to be quickly added without having to slide over the end of webbing.- Quick attachment with double Velcro® closure at bottom of pocket.Designed to add up to 5 pounds of shot or hard weight.Easy addition to XS Scuba ponypac or other harness systems.Perfect for adjusting your trim.

Features:Convert any standard regulator hose to fit a Poseidon X-Stream second stageFits any Poseidon second stage with M31-1.5mm inlet threadsBrass construction with black chrome finishDoes not have a built-in relief valveLow pressure use only - below 200 psi

Features: - Use this to route your HP hose 90º- Chromed brass construction with Viton o-rings- High pressure only – maximum 5000 psi- Cleaned for use with up to 40% pre-blended Nitrox- (1) 7/16-20 male inlet to (1) 7/16-20 female outlet

Easy Mounting of the Pony Cylinder:- Mount on the diver's right or left side- Mount upright or upside-down- Secure and stable attachment- Easy attachment with stainless steel cam buckle- No hose clampsEasy Attachment to the Primary Cylinder:- Uses your BC cam strap for attachment- Rubber bumpers to protect your cylinder's paint and finishFeatures:- Designed for 7.25 in (184 mm) diameter primary cylinders- Rubber bumpers to protect paint- 316 grade stainless steel construction- Adjustable length nylon webbing- Roller wheels make it easier to cam over the buckle and provide protection to the cylinder paint- Stainless steel cam buckle- The band can be rotated in the bracket so that the buckle

Stainless steel construction.Valve DIN insert 1/4´´ hex wrench.Port plugs 3/16´´ hex wrench.Valve dip tube 5/32´´ hex wrench.Valve nut slotted screwdriver.Phillips screwdriver.Inflator schrader valve tool.O-ring pick.Orifice adjustment flat screwdriver.

Features:- Included with Mini Tech Gauge Kit- Use to mount a Mini Tech Gauge to HP hose- Inline (180º) with the HP hose- Airspool with Viton o-rings included

Features:Install between standard regulator hose and second stage9/16-18 UNF male inlet to 9/16-18 UNF female outlet threadsSlide machined Delrin collar to shut off gas flowPrevent critical gas lossCommonly used with deco rigs, stage bottles & drysuit inflationLow pressure use only - below 200 psi

Add to any pressure gauge, console or air integrated console which uses a standard high pressure hose Remove your gauges for safe storage Bayonet mount style quick-connect (push and turn) Gauge attachment end has 7/16-20 female threads Hose attachment end has 7/16-20 male threads Airspool with iton o-rings included Brass construction with black Chrome finish.

- Add an additional high pressure port to your regulator´s first stage.- Additional port allows for 360º swivel.- One 7/16-20 male to two 7/16-20 female outlets (common HP port).- Chromed brass construction.- High pressure use - Maximum 5000 psi / 340 bar.- Factory cleaned - Viton o-rings.

Features:- Bright, white face - easy to read- Ready to mount directly to a HP port of first stage- Ready to mount directly to a HP hose- Inline adapter and airspool included- Airspool with Viton o-rings- Viton gauge o-ring- Luminescent gauge face- Wide 210º sweep- Attractive clamshell packaging

Features: - Install between first stage medium pressure port and standard regulator hose.- Slide machined Delrin collar to shut off gas flow.- Commonly used with rebreather systems.Specifications: - 3/8-24 UNF male inlet to 3/8-24 UNF female outlet threads.- Low pressure use only - below 200 psi.

Features:Convert any standard regulator hose to a BC quick disconnect hoseInstalls on the second stage end of a regulator hoseSix point attachment with six ball-bearings´EZ´ QD design, just push to attach - no need to pull back the collarWide easy grip collarA favorite for drysuit inflation hosesChromed brass constructionLow pressure use only - below 200 psiFactory cleaned - Viton o-rings

Elbow Adapter 90 second Stage.

Elbow Adapter 70 second Stage.

Male quick-disconnect only of AC990, Allows attachment of multiple second stages to a single hose, Chromed brass construction, Low pressure only - below 200 psi, Factory cleaned - Viton o-ring.,.

Regulators - Accessories.XS SCUBA Carabiner Adapter 2nd Stage 1/3 Ports.Carabiner adapter second stage 1/3 ports.

Features:Add a quick-disconnect to most any regulator or full face maskInstalls between low pressure regulator hose and second stageLock-down screw to prevent accidental disconnectionChromed brass constructionLow pressure use only - below 200 psiFactory cleaned - Viton o-ring

Rear Tail Ballast Pocket 2,7 kg.The XS Scuba Tail weight bag (2.7 kg) is designed to screw onto the lower end of the backplate to optimise the diver´s fit.Weight: holds up to 2.7 kg.

Features: - Converting your regulator/hoses to 1/4 NPT has many practical application in diving as well as your garage or shop- Used with surface supplied umbilicals, switch blocks, comm gear and pneumatic tools- Viton o-rings where applicable- 1/4 NPT male to 9/16-18 male- Stainless steel construction