Other Components

EK Water Blocks 3831109845974 EK Water Blocks EK-CSQ Extender 8mm G1/4 - Black Nickel

The EK-D-RGB 6-Way Splitter Cable allows users to connect up to six digitally addressable RGB products to a single D-RGB (addressable) motherboard or controller header so that they can synchronize all their D-RGB products. It features standard 3-pin D-RGB headers and the male-male connector pins are also included in the packaging. The splitter cable can be used with any standard 3-pin 5V D-RGB controller or any of the popular RGB sync technologies from all major motherboard manufacturers. The arrow marking on the 3-pin LED connector is to be aligned with the +5V marking on the D-RGB (addressable) header.Please refer to the motherboard manufacturer manual or RGB controller manufacturer manual …

EK-HD PETG Tube is solid type PETG tubing intended for use with EK-HD push-in adapters and EK-HDC series compression fittings. The tubing may be heat treated to achieve certain bends. For expert users only! It is mandatory to chamfer the edges of freshly cut tube in order to prevent gasket (O-ring) damage. EK recommends a 0,5mm x 45° chamfer. Specification: - Material: PETG - Inner diameter: 10 mm - Outer diameter: 12 mm - Length: 500 mm (19.5") - Clear The package contains 2 pieces of tube only. Please purchase EK-HD Adapter or EK-HDC compression fittings separately! For easier installation we recommend wetting the gasket (O-ring) using drops of water prior to installing solid tube.

The EK-HD PETG Inserts are EK's way of battling against potential hazards that the use of PETG tubes present. PETG tubes are extremely popular because of the ease of use and their flexibility. On the other hand, PETG tubing, especially the thin tube wall models (10/12) are prone to deformation when exposed to high temperatures (40°C and above). The deformation rate depends on the duration and maximum temperature reached. These temperatures can be reached with pump failures, water block clogging, etc. The EK-HD PETG Inserts provide a safety measure for 12mm OD / 10mm ID PETG tubes which prevents the tube wall from collapsing inside the compression fitting. The EK-HD PETG Insert is low …

The EK-HD PETG Inserts are EK's way of battling against potential hazards that the use of PETG tubes present.PETG tubes are extremely popular because of the ease of use and their flexibility. On the other hand, PETG tubing is prone to deformation when exposed to high temperatures (40C and above). The deformation rate depends on the duration and maximum temperature reached. These temperatures can be reached with pump failures, water block clogging, etc.The EK-HD PETG Inserts provide a safety measure for 16mm OD / 12mm ID PETG tubes which prevents the tube wall from collapsing inside the compression fitting.The EK-HD PETG Insert is low profile and it is not visible when in use with any of the …

EK-HD PETG Tube is solid type PETG tubing intended for use with EK-HD push-in adapters and EK-HDC series compression fittings. The tubing may be heat treated to achieve certain bends. For expert users only! It is mandatory to chamfer the edges of freshly cut tube in order to prevent gasket (O-ring) damage. Technical data: - Material: PETG - Inner diameter: 10 mm - Outer diameter: 12 mm - Length: 1000 mm (19.5") The package contains 2 pieces of tube only.

EK-HD PETG Tube is solid type PETG tubing intended for use with EK-HD push-in adapters and EK-HDC series compression fittings. The tubing may be heat treated to achieve certain bends. For expert users only!It is mandatory to chamfer the edges of freshly cut tube in order to prevent gasket (O-ring) damage. EK recommends a 0,5mm x 45 chamfer.Specification:- Material: PETG- Inner diameter: 12 mm- Outer diameter: 16 mm- Length: 500 mm (19.5")The package contains 2 pieces of tube only. Please purchase EK-HD Adapter or EK-HDC compression fittings separately!For easier installation we recommend wetting the gasket (O-ring) using drops of water prior to installing solid tube.

The EK-HD Tube Reamer is an external and internal tube reamer. The tool is used to remove the remains of freshly cut Acrylic, PETG, copper, aluminum, brass, carbon fiber, etc. tubing. Suitable for tubes with a minimum inner diameter of 5mm and maximum outer diameter of 30mm.Technical specification:- Plastic body- Steel blades- Minimum tubing ID: 5mm- Maximum tubing OD: 30mm

The EK-Loop D-RGB Splitter Cable 2-Way allows users to connect up to two digitally addressable RGB products to a single D-RGB (addressable) motherboard or controller header so that they can synchronize all their D-RGB products. It features standard 3-pin D-RGB headers and the male-male connector pins are also included in the packaging. The splitter cable can be used with any standard 3-pin 5V D-RGB controller or any of the popular RGB sync technologies from all major motherboard manufacturers. The arrow marking on the 3-pin LED connector is to be aligned with the +5V marking on the D-RGB (addressable) header. Please refer to the motherboard manufacturer manual or RGB controller manufacturer …

The EK-Loop D-RGB Splitter Cable 3-Way allows users to connect up to three digitally addressable RGB products to a single D-RGB (addressable) motherboard or controller header so that they can synchronize all their D-RGB products. It features standard 3-pin D-RGB headers and the male-male connector pins are also included in the packaging. The splitter cable can be used with any standard 3-pin 5V D-RGB controller or any of the popular RGB sync technologies from all major motherboard manufacturers. The arrow marking on the 3-pin LED connector is to be aligned with the +5V marking on the D-RGB (addressable) header. Please refer to the motherboard manufacturer manual or RGB controller manufacturer …

EK-Loop Modulus Hard Tube Bending Tool - 12mm is the EK approach to an easy and straight forward way of bending hardline acrylic and PETG tubing of 12mm OD. These tools act as a mold which helps the user to form the tubing in the desired shape. These tools are made to be timeless and sturdy, as they are machined out of a solid piece of black POM acetal.These tools come in 3 variants depending on the outer diameter (OD) of the tubing. Available models are for tube size of 12mm, 14mm, and 16mm.Enclosed:- EK-Loop Modulus Hard Tube Bending ToolStep by Step Instructions:Step 1: First you need to put silicon insert inside your ACRYLIC/PETG tube. You can use soap and a bit of water on silicon rod for …

EK-Loop Modulus Hard Tube Bending Tool - 14mm is the EK approach to an easy and straight forward way of bending hardline acrylic and PETG tubing of 14mm OD. These tools act as a mold which helps the user to form the tubing in the desired shape. These tools are made to be timeless and sturdy, as they are machined out of a solid piece of black POM acetal.These tools come in 3 variants depending on the outer diameter (OD) of the tubing. Available models are for tube size of 12mm, 14mm, and 16mm.Enclosed:- EK-Loop Modulus Hard Tube Bending ToolStep by Step Instructions:Step 1: First you need to put silicon insert inside your ACRYLIC/PETG tube. You can use soap and a bit of water on silicon rod for …

EK-Loop Modulus Hard Tube Bending Tool - 16mm is the EK approach to an easy and straight forward way of bending hardline acrylic and PETG tubing of 16mm OD. These tools act as a mold which helps the user to form the tubing in the desired shape. These tools are made to be timeless and sturdy, as they are machined out of a solid piece of black POM acetal.These tools come in 3 variants depending on the outer diameter (OD) of the tubing. Available models are for tube size of 12mm, 14mm, and 16mm.Enclosed:- EK-Loop Modulus Hard Tube Bending ToolStep by Step Instructions:Step 1: First you need to put silicon insert inside your ACRYLIC/PETG tube. You can use soap and a bit of water on silicon rod for …

The EK-Loop Adapter Molex to SATA enables you to connect your 4-pin MOLEX products, like D5 and DDC pumps, to a SATA power connector on your PSU.Aside from SATA being more convenient and easier to connect/disconnect than 4-pin MOLEX, this adapter helps your cable management. It removes the need for the installation of MOLEX cables thus reducing overall cable clutter and improving cable management.Enclosed:- EK-Loop Adapter Molex to SATATechnical Specification:- Colour: Black

EK-Quantum Convection DDC - Silver is an aluminum heatsink for DDC pumps. This add-on vastly improves the cooling performance of the motor and electronics and thus prolongs the lifespan of the water pump. It is made of CNC-machined aluminum that is anodized.Optimal heat transfer is ensured by the use of an enclosed thermal pad. Due to its metallic construction and finned design EK-Quantum Convection DDC amplifies the effect of airflow therefore placing the water pump in front of any fan or radiator will dramatically improve the cooling performance.This product is compatible with the following products:EK-QUANTUM KINETIC FLT DDC SERIES FLAT PUMP-RESERVOIR COMBOSEK-Quantum Kinetic FLT 120 DDC …

EK-Quantum Convection DDC - Nickel is an aluminum heatsink for DDC pumps. This add-on vastly improves the cooling performance of the motor and electronics and thus prolongs the lifespan of the water pump. It is made of CNC-machined aluminum that is nickel plated.Optimal heat transfer is ensured by the use of an enclosed thermal pad. Due to its metallic construction and finned design EK-Quantum Convection DDC amplifies the effect of airflow therefore placing the water pump in front of any fan or radiator will dramatically improve the cooling performance.This product is compatible with the following products:EK-QUANTUM KINETIC FLT DDC SERIES FLAT PUMP-RESERVOIR COMBOSEK-Quantum Kinetic FLT 120 …

EK-Quantum Inertia D5 Body D-RGB is a high-performance standalone pump-top, engineered for the market-proven Genuine D5 water pumps. It comes with an advanced vibration-reducing mounting clamp while offering increased hydraulic performance (up to 15%) compared to the original factory top. This pump-top comes with a pre-installed 3-pin 5V D-RGB LED strip for sophisticated illumination. This pump features a single inlet (on the top) and a single outlet port (on the side) for the installation of two standard G1/4 threaded fittings/barbs. This product is compatible with popular RGB sync technologies from all major motherboard manufacturers. The arrow marking on the 3-pin addressable LED connector …

Kinetic series pump-reservoir combos are part of the EK Quantum Product Line that emphasizes minimalistic, elegant design, and performance. For those who want to stand out!All new Flat (FLT) series EK-Quantum Kinetic FLT D5 pump-reservoir units! The new Kinetic combo units are part of the EK Quantum Line of products and come with sophisticated addressable D-RGB lighting implementation and a genuine D5 pump! Each unit is featuring standard 120mm fan mounting holes for maximum flexibility during the installation. The reservoir is equipped with a total of six G1/4 ports so that users can choose the most optimal setup for their liquid cooling loops.EK-Quantum Kinetic FLT D5 series pump-reservoir …

EK-Quantum Kinetic TBE 120 DDC PWM D-RGB combo unit is a pump-reservoir assembly that is based upon a market-proven DDC pump that brings the ultimate power in a small form factor. The new Kinetic combo units are part of the EK Quantum Line of products and come with sophisticated addressable D-RGB lighting implementation and a genuine DDC 3.2 pump that is a favorite among the small-form-factor PC enthusiast community! The reservoir is equipped with a total of six G1/4“ ports so that users can choose the most optimal setup for their liquid cooling loops. The DDC motor is cooled by the integrated heatsink on the bottom.The CNC-machined black POM acetal top features three G1/4" ports. One of the po…

EK-Quantum Kinetic TBE 160 DDC Body D-RGB is the stand-alone pumpless version of the newly released tubular style Kinetic TBE combo units. This means the customer is able to upgrade his old DDC-based combo unit or to utilize any existing previously owned DDC pump. These combo units are equipped with a total of six G1/4“ ports so that users can choose the most optimal setup for their liquid cooling loops.The CNC-machined black POM acetal top features three G1/4" ports. One of the ports can be used with the included nickel-plated brass internal tube, which helps prevent the splashing of the coolant inside the reservoir if the top is to be used as an inlet. This reduces the chances of air being su…

EK-Quantum Kinetic TBE 160 DDC PWM D-RGB combo unit is a pump-reservoir assembly that is based upon a market-proven DDC pump that brings the ultimate power in a small form factor. The new Kinetic combo units are part of the EK Quantum Line of products and come with sophisticated addressable D-RGB lighting implementation and a genuine DDC 3.2 pump that is a favorite among the small-form-factor PC enthusiast community! The reservoir is equipped with a total of six G1/4 ports so that users can choose the most optimal setup for their liquid cooling loops. The DDC motor is cooled by the integrated heatsink on the bottom.The CNC-machined black POM acetal top features three G1/4" ports. One of the …

EK-Quantum Kinetic TBE D5 combo unit is the revolution of the most popular pump-reservoir assembly design on the market. The new Kinetic combo units are part of the EK Quantum Line of products and come with sophisticated addressable D-RGB lighting implementation and a genuine D5 pump! The reservoir is equipped with a total of six G1/4 ports so that users can choose the most optimal setup for their liquid cooling loops.The top features three G1/4" ports, one of which has a pre-installed nickel-plated brass internal tube which helps to prevent the splashing of the coolant inside the reservoir if the top is to be used as an inlet. This reduces the chances of air being sucked in by the pump and …

EK-Quantum Momentum ROG XII Hero is the new Quantum Line monoblock specifically engineered for the ROG® Maximus XII Hero – an Intel® Z490 chipset-based motherboard. Featuring the latest generation Velocity cooling engine with low restriction and high performance. EK® Momentum series monoblocks utilize the 5th generation of the award-winning EK® CPU water block cooling engine, further tweaked for performance and optimal coolant flow! This water block directly cools Intel® 1200 socket-type CPU, as well as the power regulation (MOSFET) module. Liquid flows directly over all critical areas, providing the enthusiasts with a great solution for high and stable overclocks.…

EK-Quantum Torque HDC 12 fittings are EK's new minimalistic 12mm hard-tube compression fittings designed for use with solid tubing such as Acrylic and PETG. With a non-intrusive, yet striking look, and with NO added branding at all. They can be complemented by interchangeable aesthetic color rings, and are an ideal choice for anyone and a perfect match with EK-Quantum series products. The locking ring prevents solid tube to be pulled out of the fitting by compressing the rubber gasket underneath the ring. The grooves on the outside allow for easier hand tightening. The compression ring has cutouts in EK Quantum signature shape allowing for the colored aesthetic ring to be shown. The colored …