Guitar Amps & Cabs Aguilar

Four 12" cast frame woofers with 56 oz. magnets, phenolic tweeter with phase plug Power Handling: 1200 watts RMS Recesssed rear handles with rear wheels Custom crossover with variable tweeter control One Neutrik Speakon and two 1/4" inputs

Two 10" cast frame woofers, 56 oz. magnets, phenolic tweeter with phase plug Power Handling: 350 watts RMS Recessed deep dish handles Custom crossover with variable tweeter control One Neutrik Speakon and two 1/4" inputs

One 15" cast frame woofer, 95 oz. magnet Power Handling: 400 watts RMS Recessed deep dish handles Casters included One Neutrik Speakon and two 1/4" inputs

Four 12" cast frame woofers with 56 oz. magnets, phenolic tweeter with phase plug Power Handling: 1200 watts RMS Recesssed rear handles with rear wheels Custom crossover with variable tweeter control One Neutrik Speakon and two 1/4" inputs

Giving the Tone Hammer 700 its flexible tone-shaping capabilities is Aguilar’s Tone Hammer preamp, the same preamp used in the Tone Hammer D.I./preamp pedal, which has become a favorite of bass players all over the world. The 4.9 lb. (2.22 kg) Tone Hammer 700 delivers 700 continuous watts @ 4 or 2.67 ohms, 350 watts @ 8 ohms and features bass, treble and fully sweepable midrange controls. The Drive control utilizes Aguilar’s proprietary AGS circuit which adds subtle distortion and midrange punch to the sound. The Tone Hammer 700 also features a series effects loop, XLR balanced output and two rear panel speakon outputs. Universal mains means that this amp is ready to travel anywhere in the worl…

Extremely flexible on-board guitar preamplifier that provides +/-18dB of cut and boost at 40Hz, +/- 16dB of cut and boost at either 400Hz or 800Hz and +/- 16dB of treble cut and boost at 6.5 kHz. It comes supplied with separate Treble, Mid, and Bass pots, and black mini-toggle switch for Midrange frequency selection. Distortion: .019 into 10k ohm load. Noise: -95 dBm unweighted. Battery life: 324 hours. Dimensions: 24.9 x 24.9 x 15 mm. Made in: USA

The OBP-2 was designed to give bassists fat tone while being small enough to fit into tight control cavities. Wire this preamp with one 9 volt battery and it will fit into just about any instrument. With +/- 18dB of boost and cut at 40Hz and +/- 16dB of treble boost and cut at 6.5 kHz you have can emphasize just the right frequencies to make your bass sound great in any mix.Bass control: +/- 18 dB @ 40 HzTreble control: +/- 16 dB @ 6.5 KHzInput impedance: 1 meg ohmOutput impedance: 100 ohm 9 or 18 volts operationDistortion: .019 into 10k ohm loadNoise: -95 dBm unweighted.Battery life: 324 hoursLow noise discrete FET input stage, center detent 50 K linear pots, with a dual concentric pot availableIncludes …

The OBP-2SK was designed to give bassists fat tone while being small enough to fit into tight control cavities. Wire this preamp with one 9 volt battery and it will fit into just about any instrument. With +/-18dB of boost and cut at 40Hz and +/- 16dB of treble boost and cut at 6.5 kHz you can emphasize just the right frequencies to make your bass sound great in any mix. Controls: High;Bass Input Impedance: 1000 kOhm Height (cm): 2.5 Width (cm): 2.5 Depth (cm): 1.5 Made in: USA