Soldering Tools GYS

This easy to use tool ensures you have the correct gas flow rate providing optimum gas shielding to the weld pool. Just insert the end of the MIG or TIG torch into the meter, press the torch trigger to activate the gas flow & the black ball will hover and a litres per minute reading can be taken from the graduated markings on the meter. Approx flow required for TIG welding = 5 - 8 l/min and for MIG approx 10x the wire diameter e.g. 1mm wire = 10l/min.

Welding Protection Cover Magnets (pair) are ideal for holding welding/grinding protection blankets in place without marking the bodywork, in fact they can hold tarpaulins, poly masking sheets , masking paper etc to metal car body panels.

GYS Welding Machine Cooling Liquid is a special welding coolant essential to optimise and preserve the performance of your welding machine’s cooling circuit. Its unique anticorrosive and low-conductivity formula reduces electrolysis effects. The liquid prevents the accumulation of sediment and cooling circuit blockage compared to a standard liquid. Ready to use formula requiring no dilution providing frost resistance down to -20°C. GYS recommends that cooling liquid is changed every 2 years.

Suitable for MIG, Arc & TIG welding and is rated at 250Amps. Fitted with 35/50mm² Dinse Plug Connectors making it compatible with any machine with that size sockets. The cable length is 4 metres.

This set is suitable for MIG, Arc & TIG welding and is rated at 200Amps. It is fitted with 10/25mm² Dinse Plug Connectors, making it compatible with any machine with that size sockets. The cable length is 4metres.

Sturdy trolley compatible with TIG160DC, TIG168DC, TIG200DC, TIG300DC, TIG200 ACDC, TIG200L AC/DC, MultiPearl 200-2 7 MultiPearl 200-4XL welders.

Sturdy trolley compatible with TIG160DC, TIG168DC, TIG200DC, TIG200 AC/DC, TIG200L AC/DC, MultiPearl 200-2 7 MultiPearl 200-4XL.

Anti-Arc protects vehicle electronics from voltage surges whilst undertaking welding repairs without the need or inconvenience of disconnecting the battery from the vehicle or when performing jump start procedures. Simple to use, just connect to the positive and negative battery terminals. Green LED signifies vehicle protected, Red LED & buzzer alerts user that a surge has been absorbed and that the vehicle is no longer protected. Suitable for both 12 Volt and 24 Volt systems (2x sets required for 24V).

GYS TIG TORCH SUPPORT STAND with magnetic base holds your TIG torch off the workbench and prevents accidentally burning your torch cable, gas hose or electrical supply cable. The strong magnetic base means you can safely & securely rest your torch whilst its attached to your machine or workbench. This is a must for any welder.

This foot pedal enables adjustment of the current from the minimum current to 100% of the set current on a welding power source (MMA/TIG) equipped with a female socket for a remote control. Note - Once connected the upslope and downslope are not automatically managed by the welding power source, and are controlled by the user with the foot pedal. For more information, refer to the manual of the welding power source used.

A set of special locking clamps ideal for a multitude of uses when repairing car panels or other sheet steel work. Includes small jaw set for hard to access areas, J clamp for flanged lap joints, Small & Large L clamps for holding sills, side or quarter panels, wide flat jaw clamps for spot or plug welding (allows 4 spot welds without removal) & trim clip removal tool.

GYS Multicool 1300 Universal Welding Machine Water Cooling Unit is a system designed to cool water-cooled torches connected to all types of welding machines (GYS or other brands). This device is autonomous and has its own power supply. The operation of the torch trigger can be controlled by liquid flow detection to protect the torch from overheating. Fitted with standard water cooled torch quick connectors, integrated flow sensor to protect torch from overheating due to a blockage and having a reinforced metal case and non-slip rubber feet. Rated IP23 S for outside use. GYS recommends filling with its low conductivity welding machine coolant with rust inhibtor (010132511).

The Jobsite XL trolley not only provides easy mobility but also storage for your welding machine. Torch and earth clamp are also easy to access with the trolley. The trolley is compatible with most welding machines that fit the 584mm wide x 331mm deep base plate but spefically for the following GYS machines: MMA - Progys CEL 250 TRI Progys Flex 250CEL Exagon 400. TIG - TIG DC 160/168/200/250/300/Titan400 Protig 201/201L/220 Titanium400 AC/DC. MIG - Multiweld 250TCMultipearl 200-2 & 200-4 Plasma Cutters; Cutter 25/35/70/85TRI/125TRI/Neocut105. Optional gas bottle support tray is available (010129551).

The DRY 5.200R electrode oven is a mobile device in which coated electrodes are kept at high temperature. Electrodes can absorb moisture whilst in storage & excess moisture can produce low quality, porous welds. The electrode oven is designed to hold up to 5kg of electrodes (maximum length of 450mm), is extremely portable & ideal to use whilst working on site. The 5.200 also has an external temperature gauge & adjustable thermostat which is adjustable in 50°C increments.

The DRY 5.150R electrode oven is a mobile device in which coated electrodes are kept at high tempereture. Electrodes can absorb moisture whilst in storage & excess moisture can produce low quality, porous welds. The electrode oven is designed to hold up to 5kg of electrodes (maximum length of 450mm), is extremely portable & ideal to use whilst working on site.

The compass kit allows you to quickly cut precise circles of diameters up to 134 cm (max). Ideal for making circular cuts between 40cm and 134 cm in diameter. Magnetic centring device for fast cuts on all ferrous surfaces. Screw-in centring device for non-metallic materials. Needle punch centering device for precise centering without perforating the sheet metal. Compatible with plasma torches MT25K/MT35K/TPT40 - Z.

Quality electrode holder compatible with all makes of Arc or TIG welders that have 35/50mm² sized Dinse sockets

Quality electrode holder compatible with makes of Arc or TIG welders that have 10/25mm² sized Dinse sockets.