Comparison Nokta Makro Simplex Ultra vs Garrett AT Pro

The shape of the coil (frame) of the metal detector.

— Round. The traditional form used in almost all types of ground and underwater metal detectors (see "Type"); the only exceptions are models that work according to the RF method (see "Operating principle"). When using concentric coils (see "Coil Type"), this option allows you to create a conical field, which is convenient for pinpointing the location of the find, but reduces the covered area and makes it difficult to search over a large area; models with DD coils do not have this drawback.

— Elliptical. The shape in the form of a longitudinally elongated ellipse allows you to somewhat "stretch" the field created by the metal detector in length. This is especially true for coils of the concentric type — however, such an expansion somewhat reduces the positioning accuracy of individual finds. But in coils of the DD type, where the accuracy is by definition low, the choice between round and elliptical shape is most often not fundamental.

— Rectangular. A specific form used in RF or PI instruments. For technical reasons, it is considered optimal for such devices, but it is practically not found in other types of metal detectors.

— Butterfly. Another option used in DD coils along with the ellipse (see above). In fact, it consists of two elliptical windings..., partially combined and resembling butterfly wings in shape — hence the name. This option is typical mainly for large-sized DD coils; with a large width, it is considered more optimal than an ellipse.

The size of the standard coil (frame) of the metal detector. Theoretically, the larger it is, the deeper the device is able to “see” and the more space it captures in one pass, but the worse it is suitable for searching for small objects and the lower the accuracy with which it localizes them. At the same time, these characteristics depend on so many other factors that in fact, the size of the coil itself affects them very little.

Note that for coils (frames) of an elliptical shape, only one size can be indicated — along the length.

The greatest depth at which a metal detector is guaranteed to be able to detect a metal object. Note that this parameter is most often quite approximate, moreover, somewhat conditional. This is due to the fact that it is usually indicated for an perfect environment (low-mineralized soil, a fairly large object, the material of which optimally matches the frequency of detection of the coil, etc.), and even for such conditions it is difficult to derive an absolutely accurate value. Therefore, in fact, the detection depth is highly dependent on a number of additional factors (from soil characteristics to user skills) and can be significantly less than indicated in the characteristics. Nevertheless, the claimed depth describes the capabilities of the metal detector quite well, and it is quite possible to compare different models with each other.

Note that a large depth not only increases the cost of the device, but can also adversely affect its ability to detect small objects.

The deepest depth at which a metal detector is capable of detecting small coins and other objects of similar size. Many users buy a device with the intention of “hunting” for metal trifles, so manufacturers often indicate this parameter separately in the specifications. Due to the small size of the coins, their detection depth is usually much less than the total maximum detection depth (see above).

The number of individual discrimination programs provided in the design of the metal detector. In this case, discrimination means filtering the detected objects using a discriminator (see above) so that the device does not work on unwanted objects such as pieces of foil, bottle caps, etc. You can also configure such a filter completely manually, but this may require special knowledge and create difficulties for inexperienced users. To avoid this, some models may have preset programs instead of manual settings. Thanks to such programs, the user just needs to select from the list what type of objects the metal detector should react to, and all the necessary settings will be set by the device's electronics.

Regular metal detector search programs include detection of coins, all metals, jewelry and relics. In some models, this list can be expanded with "Beach" programs, custom (user) detection mode, etc.

— Pin-Point mode(target designation). Possibility of operating the device in the so-called static mode, when the detection accuracy increases significantly (due to a decrease in range and discrimination ability). Note that this function is not found in pinpointers (see “Type”), despite the similarity of names - such devices are very accurate and without special modes. And among classic mine detectors, the Pin-Point mode is used only in models operating on the VLF or VFLEX principle (see above) - for other operating principles this function is, for one reason or another, irrelevant. Be that as it may, this feature can be very useful in accurately searching for small objects. The fact is that a classic VLF/VFLEX metal detector is able to “see” objects only if the coil moves above the ground - this simplifies discrimination, but noticeably reduces accuracy. In static mode, the device operates even in a stationary position, and the coil can be moved very slowly, which significantly increases the search accuracy.

— Setting sensitivity. Ability to change the sensitivity of the metal detector. High sensitivity makes it possible to search at great depths, but at the same time reduces resistance to interference, increases the likelihood of false positives and does not allow you to accurately determine the location of individual finds in places where signals are densely located (the device reacts to a group...of objects as a whole and cannot identify separate). Yes, and ground balancing (see above) is also connected. and with sensitivity. Therefore, this parameter is very important for setting up the metal detector for a specific situation.

— Threshold tone. The threshold tone is a low, monochromatic hum that the metal detector’s speaker or headphones emit in “neutral” mode, when there are no alarms. This feature has several uses. So, the tone can serve as an indicator that the device is turned on and working normally; This is especially true for models not equipped with displays. The pitch of the sound may change when the characteristics of the surface under the coil change - for example, when moving to soil with a different level of mineralization, or when detecting objects that “do not reach” the response threshold due to their small size or deep location; experienced users know how to use these tone changes for work purposes.

— Detuning from electrical interference. The presence of this function in the metal detector allows you to neutralize the influence of electromagnetic interference and prevent both “blurring” of the signal and false alarms. Such interference can occur for various reasons: from the proximity of power lines, radio transmitters or locators, when working near vehicles with running engines or near other metal detectors, etc.

— Tone identification. This function assumes that the metal detector, when triggered, emits signals of different heights - depending on the expected material and size of the find, its depth, etc. This feature is especially important for models that do not have a display. Tone identification requires some getting used to, but usually even inexperienced users do not have problems with it.

— VDI / Target ID identification. Metal detector function that helps to more accurately determine the type of metal. It is based on the display on the display of a numerical value inherent in a certain class of metal. Thanks to the table, you can significantly narrow the range of possible detected objects.

— Determination of target depth. A device function that helps determine the depth of the desired target. It is based on displaying on the display the numerical value of certain units of length measurement or highlighting segments of the depth scale.

— Vibration response. The presence of a vibration response system in the design of the metal detector. This system allows the device to send a signal by vibration of the case (similar to how this happens, for example, in mobile phones). In some cases, such a signal may be more convenient and appropriate than sound or visual indication. For example, when using a ground metal detector, the vibration of the device in your hand will almost unmistakably indicate that it has triggered, while the sound may be “lost” in the surrounding noise, and the visual indicator may be out of sight at the right moment. And in an inspection pinpointer (see “Type”), the vibration response can also be useful as a “silent warning” - so that the signal is not audible to the subject being inspected and at the same time reliably warns the operator.

— Volume adjustment. The presence in the design of a regulator that allows you to change the volume of the sound signal from speakers or headphones. Such a regulator can be located on the control unit, on the handle, on the headphones, etc.; however, in all cases its operating principle and purpose are the same.

— Low battery indicator. The metal detector has an alarm system that warns of low battery levels. This function informs you in advance about the need to take care of a fresh power source and prevents situations where the battery unexpectedly “dies” at the most inopportune moment. Note that the specific implementation of the indicator may vary: the signal can be visual or audio, and in some models, data on the battery status is displayed only upon the user’s command.

— LCD display. The presence of its own display in the design of metal detectors. This feature makes working with the device more convenient and visual: through the display, you can display more different information than with the help of an audible alarm or indicator lights, and it is easier to perceive. On the other hand, such devices are more expensive than similar models without a screen.

— Arrow indicator. The presence in the design of the metal detector of an analogue dial indicator to display data on the search process. Such an implementation is much more modest and cheaper than the same LCD display, but an order of magnitude more convenient than without visual notification at all.

— Display backlight. The presence of a backlight allows you to use the display of the metal detector in low light conditions — up to complete darkness. Note that this function can be useful not only at dusk, but also in the daytime — for example, when searching in a dense forest in cloudy weather. See above for details on the display.

— Built-in speaker. The presence in the design of the metal detector of its own speaker. Such a speaker allows you to use the device without headphones, which are not always convenient, and sometimes unsafe (for example, when working in places where traffic can move).

— GPS module. The pre...sence of a GPS satellite navigation module in the design of the metal detector. This module allows you to determine the current geographic coordinates of the device, and the options for using this data can be different: recording search routes, fixing the places of individual finds, and even full-fledged navigation with laying routes from point to point.

— Armrest. The presence in the design of the metal detector of an additional support in the area of the operator's elbow. This support reduces the load on the hand, and also makes the hold more stable and at the same time controllable, allowing you to comfortably hold the device in one hand.

— Headphone output. The presence of a headphone output in the design of the metal detector. This can be either a standard connector that allows you to connect any compatible "ears" (for example, a 3.5 mm mini-jack output, popular in portable audio equipment), or an original proprietary interface that allows you to use only specialized "native" accessories. Anyway, headphones are often more convenient than a speaker, as they allow you to hear the signals from the device well even in a rather noisy environment.

— Headphones. The presence of headphones in the scope of delivery of the metal detector. Usually, such headphones have high quality and accuracy of sound transmission, so that the user can be guaranteed to hear all the signals and tone shades of the signals. "Ears" can be wired and wireless, and in underwater models (see "Type"), they are, respectively, made waterproof. This function is convenient because you do not have to search and purchase the best headphones for the metal detector on your own.

— AA. Replaceable elements, known colloquially as "finger" type. They can be both in the form of disposable batteries and in the form of rechargeable batteries. They are produced by many manufacturers, and different brands differ in price and quality, which gives many opportunities to choose the optimal option. And AA batteries are sold almost everywhere. On the other hand, they are usually required in large quantities — about 8, because metal detectors consume quite a lot of energy; and the elements themselves are most often not included in the set.

— PP3. Replaceable batteries of standard size, in a characteristic rectangular case with a pair of contacts at the end, nominal voltage of 9 V. They are more powerful than the popular AA elements, but they are noticeably less common. They can also be produced in the form of rechargeable batteries.

— Proprietary battery. Tools powered by its own battery (often built-in), which does not correspond to the standard sizes of replaceable elements. Such batteries can have a high capacity and power and are often more convenient than replaceable elements. In addition, they are usually supplied with the device, which eliminates the need to look for power supply yourself. The main disadvantage of this option is the impossibility of quick replacement in case of exhaustion of the charge — the battery will have to be cha...rged, and this requires not only a power source, but also time. Theoretically, if the battery is removable, you can keep a spare charged battery ready, but in practice, spare elements are expensive, and it may be difficult to find them. For a number of technical reasons, such type of rower supply is rare, it can be found mainly in high-end models.

— 18650. The name of these batteries comes from their dimensions: 18.6 x 65.2 mm, cylindrical in shape, they look like slightly enlarged AA, but have an operating voltage of about 3.7 V and a higher capacity. In addition, all elements of the 18650 type by definition are not disposable, but rechargeable batteries (lithium-ion type).

— C. Replaceable elements of standard size, cylindrical shape, with a nominal voltage of 1.5 V. In length, they practically do not differ from the AA described above, but they are much thicker, due to that they have a higher capacity. At the same time, this type of power supply is quite rare; this can be said about the batteries themselves as well.