Comparison Harley Benton ST-20HH Active vs Harley Benton HWY-25

The type of tone block used in the construction of an electric guitar.

A timbre block is an “intermediary” between a pickup and a guitar output: a set of electronic circuits that provides signal transmission, and often also its processing (volume control, frequency correction, preamplification, etc.). In modern electric guitars, there are such types of tone blocks:

— Passive. Passive are called timbre blocks that do not require additional power sources during operation. Usually, such modules have the simplest design and functionality, adjustments are limited to changing the volume, as well as passively correcting frequencies (by “cutting off” the desired frequencies). At the same time, passive tone blocks are simple, compact, inexpensive and do not depend on batteries; and the necessary adjustments can be made on external equipment (anyway, the electric guitar will need to be connected to it). As a result, most modern instruments are equipped with this particular type of tone blocks.

— Active. The key difference between a passive tone block is that it needs its own power source to work. Most often, this role is played by a PP3-type battery installed in a special socket in the body of an electric guitar. The need for power is due to the abundance of additional functions: active tone blocks are able to amplify the signal coming from the pickups, suppress interference, and even match the output impedance of the inst...rument with the input of the amplifier. Yes, and the active method of tone control is more advanced than the passive one, it allows you to more accurately adjust the frequency ratio. On the other hand, active modules are noticeably more expensive, and without a battery, the tone block turns into a set of useless parts. However, such devices consume relatively little energy, and one battery lasts for quite a long time.

— Active/passive. Tone blocks that combine the capabilities of the two options described above. If there is power, such a module operates in active mode, and if there is no power, it turns into passive. Thus, the musician can enjoy all the advantages of the active tone block and at the same time not worry that the instrument will become completely useless due to a dead battery (although, of course, the tone block functionality is not so extensive in the passive mode). At the same time, combined modules are quite complex and expensive, and the real need for such versatility is rare. Therefore, this option has not received much distribution.

The number of tone controls provided in the design of an electric guitar.

One tone control is responsible for the sound of the electric guitar as a whole; but if there are several such pens, they can have different formats of work. So, each knob can be responsible either for its own pickup, or for a separate frequency band. In the second case, a set of knobs plays the role of an equalizer that allows you to adjust the sound by changing the volume of low and high (sometimes even separately middle) frequencies.

Anyway, the presence of several tone controls expands the possibilities for changing the coloring of the sound by means of the guitar itself, without the use of additional equipment.

The general shape of the body of an electric guitar.

The solid body of an electric guitar can be molded into almost any shape; hollow cases do not give such freedom, however, even among them, the options in shape can be very diverse. However, there are certain standard forms. It is not uncommon for these shapes to be named after a particular "legendary" guitar model, such as the "Les Paul" or "Stratocaster" (after Gibson and Fender instruments of the same name, respectively). It makes no sense to describe each standard form — it's easier to find an illustration in our catalog or on the Internet.

The main, and often the only point, which is affected by the shape of the body is the appearance of the guitar. Also, convenience for the musician to some extent depends on this parameter — for example, some models allow you to play while sitting, resting the instrument on your foot, for others this method is weak or not suitable at all. But whether the shape of the body affects the sound of an electric guitar is a moot point. There is an unequivocal dependence only in semi-acoustic models, but for solid bodies there is no clear answer to this question: some musicians claim the superiority of some forms over others, but this moment is largely subjective. In addition, other parameters (types and number of pickups, bridge design, etc.) greatly affect the sound quality.

Now on the market there are guitars with this body shape: Les Paul, Superstrat, Stratocaster, Jazz Bass, Precision Bass, Telecaster, PRS Santana, Flying V, SG, however, there are also completely non-standard options.

The presence of a protective lining (pickguard) on the body of the guitar.

Such an overlay is located on the upper deck, most often made of durable plastic and differs markedly in colour, due to which it is clearly visible. Its main purpose is to protect the soundboard surface from pick strikes (for example, when playing with dynamic fighting), which could damage the varnished wooden surface. The specific shape and size of the fingerboard may vary, but anyway, it covers at least the surface below the strings (when looking at the guitar in the working position), and sometimes under the strings and even above them.

The material from which the body of an electric guitar is made. For models with cutouts (semi-acoustic, see "Type"), in this case, only the material of the back deck and sides can be taken into account, and data on the top deck is given separately (for more details, see "Deck Cover Material").

Now on the market there are cases of such trees: red, maple, agatis, ash, alder.

It makes no sense to dwell on each of the materials found in modern electric guitars. Their variety is very large, however, unlike acoustic guitars, the body in this case does not play such a significant role in shaping the sound, and its material has a relatively small effect on the acoustic properties of the instrument (although the exact degree of such influence is a moot point). If you wish, you can find detailed data on a particular material in special sources, but in fact it makes sense to look primarily at the appearance of the instrument and its price category.

The type of bridge provided in the construction of the guitar.

The bridge is often referred to as the part used to secure the strings to the body, but this is not entirely true. There are many models where the bridge plays only the role of a nut (limits the length of the scale), and the string is fixed in a separate device (stop bar) or even in the guitar body, through the method (see below).

All modern breeches can be divided into two main categories. The first is fixed, in which the strings are fixed, and the tightening during the game can only be performed with the left hand on the fretboard. They somewhat limit the set of techniques available to the musician, but they are inexpensive, compact and do not complicate the tuning of the guitar. The second variety is tremolo("machines"), which have a lever under the guitarist's right hand, allow you to change the tension of all the strings at once and achieve interesting effects that are not available with a conventional tightening. The disadvantages of "machines" are the opposite of the advantages of "fixes": tremolo bridges are more expensive, often cumbersome, with frequent use they can quickly detun the instrument, and tuning is often quite difficult, requiring specific skills and tools. Note that tremolo machines are used only in electric and semi-acoustic guitars, bass guitars are equipped only with fixed tailpieces.

The main...types of bridges found in modern electric guitars are as follows:

— Fixed. This designation is used for all fixed breeches other than the popular varieties described below.

— Hardtail (fixed). A distinctive feature of "hardtails" is a metal plate that plays the role of the basis for other mechanics. Such a plate is installed on the top deck; it is bent up from the far side (from the fretboard), and the saddles for the strings are attached simultaneously to the base and to the bent part. The fastening of the strings is often done through. This type of bridge allows you to individually adjust for each string not only the length of the scale, but also the height above the fretboard.

— Tune-o-Matic (fixed). Bridge in the form of a plank, on which saddles for strings are fixed. In this case, the strings can be attached to the body of the guitar (through method), to a separate stop bar or in the holes on the bridge itself (however, the latter is rare). Tune-o-Matic allows you to individually adjust the scale for each string, however, the height above the neck is changed only by changing the height and inclination of the bar (for this, an adjustment screw is provided at each end of the bar).

— Tremolo. Tremolo machines that do not belong to any of the varieties described below; this option is also indicated in cases where the manufacturer, for some reason, did not specify the specific type of "car". This category includes mechanisms that are quite diverse in design and functionality, so the features of such a bridge in each case should be specified separately.

— Vintage Tremolo. One of the first varieties of tremolo machines, developed by Fender. Externally, such a device looks like the Hardtail described above, supplemented by a movable (swivel) mount and a lever for adjusting the tension; fastening strings — most often through. Keep in mind that Vintage Tremolo's are designed primarily for downtuning; it is possible to raise the system with the help of such a machine only slightly, and then this will require certain tricks. Another drawback is that heavy use of the tremolo arm detunes the guitar quite quickly — especially if the player has neglected the tuning rules, which, although not difficult for Vintage Tremolo, are quite specific. On the other hand, “vintages” are inexpensive, and you can compensate for the mentioned drawback, for example, by using a top lock. The classic "vintage" is attached to the body with six screws, but there are also twin-screw versions — they are simpler and at the same time keep the system longer with active use.

— Wilkinson (tremolo). A further development of the design of the Vintage Tremolo described above. One of the key differences of the "Wilkinson" is that the strings in it are held on the bridge itself, and not on the body of the guitar. Because of this, this type of breeches stay in tune much better than the original "vintage" breeches. In addition, the lever in such "machines" is attached without thread, so that the likelihood of backlash is reduced to zero. On the other hand, Wilkinson bridges are noticeably more expensive, and their main function is to lower the tuning (although, again, with some tricks, a slight increase is possible).

— Bigsby (tremolo). Another representative of the "timeless classic", perhaps the first tremolo system in the world. Today it is used mainly on vintage-style guitars; particularly well suited for semi-acoustic instruments, as attached to the end of the guitar, not to the thin top, and does not place heavy loads on the soundboard. A distinctive feature of the Bigsby is that as a stop bar to which the strings are attached, such machines use a round rod that rotates from the movement of the lever and thus changes the tension of the strings. Due to this, such bridges have a number of advantages: they can work both down and up, they are easy to tune and keep the system well and respond to the slightest movement of the lever, allowing the musician to control the sound very precisely. In addition, Bigsby systems have a stylish appearance. On the other hand, they are quite massive and bulky, expensive, and the adjustment range is relatively small (smaller than that of the same Floyd Rose).

— Floyd Rose (tremolo). One of the most popular tremolo systems used by professional musicians. It is similar in design to the Vintage Tremolo, in particular, it is also mounted on two bolts and has a spring that compensates for the tension of the strings. However, the design of the Floyd Rose allows the action to be changed both downwards and upwards (increasing the tension), providing possibilities that are not available with "vintage" and similar systems; and similar machines differ from Bigsby in a wider range of adjustment. Note that the design of instruments with such bridges usually includes a top-lock — a device that clamps the strings on the fingerboard at the nut. Thanks to this, the “floyd roses” perfectly keep the system when actively working with the lever. All this led to the popularity of these systems among guitarists. On the other hand, setting up and caring for such breeches is a very difficult, painstaking and delicate matter. So, for setting strings and tuning, a whole set of keys may be required; when a string breaks, the system “floats”, and replacing a damaged string is inevitably associated with retuning the entire guitar; moreover, the system can go astray even from inaccurate movement of the instrument or a strong blow with the palm when muting the strings. Therefore, Floyd Rose type machines are mainly recommended for advanced guitarists with experience in handling electric guitars. And even professional musicians sometimes prefer to go to the master, rather than messing around with the service themselves.

— Kahler (tremolo). A system similar to Floyd Rose, but without springs and fixed directly to the body, usually with 4 screws. This allows you to slightly increase the sustain (due to improved contact of the strings with the body). The rest of the advantages and disadvantages are in most cases the same as Floyd Rose. However, high-quality solutions are also produced under the Kahler brand, which are not cheap, but have an improved design and are devoid of a number of disadvantages — in particular, such models are insensitive to changes in the position of the instrument and sharp muting of the strings with the palm of your hand.

— Zero Resistance (tremolo). Another improved version of the Floyd Rose described above, which is distinguished by the presence of a blocker — a device that rigidly fixes the bridge. Thanks to this, the system does not “float” when the string breaks, and the tuning of the guitar is noticeably simplified compared to the original Floyd Rose. The disadvantage of ZR is traditional — a high price.

It is worth noting that the above list does not include specific brands of bridges, but only their general types; within the same type, there may be models that differ somewhat in design and functionality.

The fret is the gap between the nut on the fretboard; each such interval is responsible for its own note (the interval between the frets is half a tone). Accordingly, the more frets, the more notes you can play on one string. However, keep in mind that the width of the gaps between the nut decreases as you get closer to the bridge, and if there are a lot of frets, playing at high frets can be difficult, requiring very high accuracy.

The most popular options today are 22 or 24 frets, they are found in most electric guitars of all types. In basses, there are also a smaller number ( 20 frets and 21 frets), because. the distance between the nut on such instruments is greater, and the necks, respectively, with the same number of frets, are longer than those of guitars.

In general, paying attention to this parameter makes sense, first of all, for professional musicians, for whom a vast “space for manoeuvre” is fundamentally important.

A separate category is fretless instruments, completely devoid of nut. Almost all of them relate to bass guitars; there are also electric guitars without frets, but very rarely. In such instruments, the role of the nut is played by the musician's finger, which presses the string to the fretboard. The technique of playing fretless guitars is noticeably mor...e complicated: firstly, to extract clean notes, you need a very precise position of the finger; secondly, this design reduces the volume of the sound and the duration of the sustain, and special playing techniques may be required to obtain the sound of the desired volume (and heavier strings for basses). On the other hand, the lack of frets gives the professional musician a number of additional options. For example, on a fretless neck, you can make very smooth slides, without stepping between notes, and the instrument itself is not tied to a standard 12-step scale, which can be very useful in some areas of music (experimental, oriental, etc.). Also note that the fretless bass guitar, both in sound and playing technique, is very close to the classical double bass, which is especially appreciated by lovers of jazz and other similar styles.

Profile of a fretboard mounted on an electric guitar.

The profile of the neck is called its shape in section, more precisely, the shape of the back of the neck. This parameter practically does not affect the sound of the guitar, but it directly affects the convenience of playing. Ideally, the neck should “fill” the hand, but not be too large — otherwise it will not be possible to clasp it to the right extent.

Profiles are denoted by the letters C, D, V and U — depending on which letter the neck resembles in the section. Profile D is the flattest, C is slightly more convex, with almost uniform curvature along the entire length, U is more voluminous, with a wider profile in the area of the lining, and the V profile in its classic form has the form of an angle with a rounded top. There are also modifications of these options — for example, "thin", which provides for a reduced profile thickness, or "modern", with slightly improved (theoretically) ergonomics.

The most popular profile types are C, U and their "modern" (modern) modifications. The C profile is almost semi-circular, the U profile is more voluminous, at the fingerboard its edges are almost parallel and only closer to the back of the neck are sharply rounded. The terms modern C and modern U refer to various improved versions of these profiles, their f...orm may be different.

In fact, the choice of neck profile depends solely on the guitarist's personal preferences, the characteristics of his hands and his preferred playing technique. Thus, there is no "perfect" profile shape — in each case, the optimal choice will be different. The perfect option is to try several types of profile "live", decide which one will be more convenient, and choose an instrument with a neck of the same or similar profile shape.

The radius of curvature of a fretboard mounted on the fretboard of an electric guitar.

The fingerboard is located directly under the strings, it is to it that the musician presses the strings when playing. If you look at the neck in cross section, its upper part with the overlay will have the shape of an arc; the radius of this arc is implied in this case. The smaller the radius, the more convex this arc will be, and vice versa, a large radius will correspond to an almost flat surface.

In general, it is believed that a smaller fingerboard radius is better for playing chords, and a more even, flat surface makes it easier to play technical passages with an abundance of special techniques such as bands. The average and, one might say, classic diameter value is 12", this is the most popular option among modern electric guitars. The smallest figure is just over 7", it is found in some guitars with Stratocaster bodies (both original Fender instruments and copies ). And the most flat pads have a diameter of 20" or more.

Note that there are often instruments with a variable fretboard radius — smaller at the headstock (where chords are played more often) and larger near the body (where solos are played by notes). In such cases, the radius at the nut is indicated.