United Kingdom
Catalog   /   Sound & Hi-Fi   /   Hi-Fi & Hi-End Components   /   AV Receivers

Comparison Onkyo TX-SR373 vs Onkyo TX-SR343

Add to comparison
Onkyo TX-SR373
Onkyo TX-SR343
Onkyo TX-SR373Onkyo TX-SR343
from £1,083.48 
Outdated Product
from $360.00 up to $367.20
Outdated Product
TOP sellers
Device typeAV ReceiverAV Receiver
CPU
DAC frequency192 kHz192 kHz
Audio DAC24 bit24 bit
Auto sound calibration
Auto level
Ultra HD4K4K
UpscalingUltra HD (4K)Ultra HD (4K)
3D
Tech specs
Number of channels5.15.1
Power per channel
100 W /8 Ohm/
100 W /6 Ohm/
Signal to noise ratio106 dB100 dB
Acceptable acoustic impedance6 Ohm6 Ohm
Frequency range5 – 100000 Hz
10 – 10000 Hz /+ 1, - 3 дБ/
Media player and tuner
Tuner and playback
AM/FM radio
USB drive
AM/FM radio
USB drive
Playable formatsMP3, WMA, AACMP3, WMA, AAC
Communications (interface)
Interfaces
Bluetooth
Remote control negotiation
Bluetooth
Remote control negotiation
Decoder support
Decoders
Dolby Digital
Dolby Digital Plus
Dolby TrueHD
Dolby Pro Logic II
DTS
DTS Express
DTS 96/24
DTS-HD High Resolution Audio
DTS-HD Master Audio
DTS Neo:6
Dolby Digital
Dolby Digital Plus
Dolby TrueHD
Dolby Pro Logic II
DTS
DTS Express
DTS 96/24
DTS-HD High Resolution Audio
DTS-HD Master Audio
DTS Neo:6
Inputs
RCA3 pairs6 pairs
Coaxial S/P-DIF1 шт1 шт
Optical1 шт2 шт
HDMI4 шт4 шт
HDMI versionv 2.0
Composite2 шт3 шт
Component2 шт
Outputs
RCA1 pairs
HDMI1 шт1 шт
Composite1 шт1 шт
On headphones6.35 mm (Jack)6.35 mm (Jack)
Front panel
Headphone output
Linear
 /pair RCA/
Composite
General
Power consumption220 W370 W
Standby consumption0.3 W0.2 W
Dimensions (WxDxH)435x327x168 mm435x328x160 mm
Weight8 kg7.8 kg
Added to E-Catalogmarch 2017november 2015

Auto sound calibration

In this case, the function of automatic adjustment of each individual sound channel in terms of level and delay is implied so that all of them together provide surround sound that best matches the intention of the creators of the film or musical composition. The need for such a setting is due to the fact that practically no room (neither residential, nor even specialized) is acoustically perfect: the sound propagation is affected by the wall material, floor covering, furniture (sofas, wardrobes, etc.) and other factors. Therefore, the technically correct arrangement of the speakers alone does not guarantee a full-fledged surround sound.

Typically, automatic tuning uses a microphone placed at the intended listening position. During the calibration process, the device outputs test sound signals through the acoustics and “listens” to the features of the sound through the microphone, if necessary, independently changing the audio parameters.

Such a function can greatly simplify the preparation for work — after all, the device will carry out the main part of the setup on its own. However, keep in mind that even in the most advanced receiver models, automatic calibration algorithms are not perfect. As a result, it is highly likely that the automatically set parameters will not meet the tastes of demanding audiophiles. In addition, the reliability of the calibration is also highly dependent on the characteristics of the microphone used — and options with high...sound quality can be quite expensive.

Signal to noise ratio

This indicator determines the amount of extraneous noise that accompanies the sound output by the receiver's amplifier. It is convenient because it takes into account almost all possible significant noise — both created by the device itself and due to external causes. The higher the signal-to-noise ratio, the lower the noise volume compared to the main signal, the cleaner the amplifier will sound. A reading of 70-80 dB is considered normal for most consumer electronics, but in AV receivers, which are usually premium devices, this can only be called satisfactory. In the most advanced models, this figure can significantly exceed 100 dB.

Frequency range

The range of sound frequencies that the receiver is capable of outputting (this parameter can also be specified for models without their own amplifier, see “Number of channels” for more details). The completeness of the transmitted sound depends on this parameter; of course, the sound quality in general is highly dependent on a number of other factors (for example, frequency response), but the wider the frequency range, the less risk that the amplifier will completely “cut off” some part of the sound. On the other hand, it should be taken into account here that the normal hearing range of the human ear is approximately 16 – 20,000 Hz, and deviations from these limits are rather small. And although many modern receivers provide a much wider frequency range, however, this is more of a marketing ploy than a really significant indicator (or some kind of "side defect" in the design of a high-quality amplifier).

It is also worth considering that in order to reproduce the full frequency of the amplifier, you will need speakers with the appropriate characteristics.

RCA

The number of analogue stereo RCA inputs provided in the design of the AV receiver. The more such inputs there are, the more transmitting devices can be simultaneously connected to the receiver. Thanks to this, when choosing between them, you do not have to reconnect cables — just set the signal source in the receiver settings.

By itself, the RCA connector (colloquially — "tulip") can be used in different interfaces. However, in this particular case, we are talking about a linear audio input responsible for an analogue audio signal. RCA is the most popular connector used in modern audio equipment for such inputs; it allows you to connect the receiver to an external audio source such as a CD player.

Note that connectors of this type are usually counted in pairs; in other words, one input consists of two RCA connectors. This is due to the fact that in this case only one channel of analogue audio can be transmitted over one wire; accordingly, two RCA jacks are required for stereo transmission.

Optical

The number of optical inputs provided in the design of the receiver.

The optical interface allows digital audio to be transmitted and is in fact a variation of the S/PDIF standard using a fiber optic data link (TOSLINK cable). In terms of bandwidth, it is completely similar to the coaxial interface (see above) — in particular, it supports multi-channel audio — however, it compares favorably with its complete insensitivity to electromagnetic interference. On the other hand, due to their design, optical cables are sensitive to sharp bends and mechanical stress — accidentally stepping on such a cable can make it unusable. In addition, they have a maximum length limit of about 6.1 m.

As for the quantity, the presence of several inputs allows you to connect several signal sources to the receiver at once with the corresponding outputs and switch between them through software settings without fiddling with switching cables.

HDMI version

HDMI interface version supported by the receiver. Usually, all HDMI connectors available in the device correspond to this version — both inputs (see above) and outputs (see below). Here are the current options:

— v 1.4. The oldest of the current versions, released in 2009. However, it supports 3D video capable of working with resolutions up to 4096x2160 at 24 fps, and in Full HD resolution, the frame rate can reach 120 fps. In addition to the original v.1.4, there are also improved modifications — v.1.4a and v.1.4b; they are similar in terms of basic features, in both cases the improvements affected mainly work with 3D content.

-v 2.0. Significant update to HDMI introduced in 2013. In this version, the maximum frame rate in 4K has increased to 60 fps, and the audio bandwidth has increased to 32 channels and 4 separate streams simultaneously. Also from the innovations, we can mention support for the ultra-wide format 21:9. In the v.2.0a update, HDR support was added to the interface capabilities, in v.2.0b this feature was improved and expanded.

— v 2.1. Despite the similarity in name to v.2.0, this version, released in 2017, was a very large-scale update. In particular, it added support for 8K and even 10K at speeds up to 120 fps, as well as further expanded the possibilities for working with HDR. Under this version, its own cable was released — HDMI Ultra High Speed, all v.2.1 features are available only when using cables of this standard,...although basic functions can be used with simpler cords.

Composite

The number of composite inputs provided in the design of the receiver.

Note that in this case, we do not mean a full-size composite interface that uses three sockets (video and two stereo sound channels), but only one connector — video. This is due to the fact that the sound can be output through standard RCA audio connectors. The video output also uses an RCA type connector, usually a characteristic yellow colour.

Due to the fact that all image data is transmitted over a single cable, the composite interface is somewhat inferior to the component (see above) in terms of video quality, and the bandwidth allows you to work only with a standard definition signal (not HD); and there is no talk of volumetric sound. On the other hand, this connection method has long been used in video technology and can be useful for connecting outdated devices (such as VHS VCRs).

As for the quantity, the presence of several inputs allows you to connect several signal sources to the receiver at once with the corresponding outputs and switch between them through software settings without fiddling with switching cables.

Component

The number of component inputs provided in the design of the receiver.

This interface (also known as YPbPr) is designed to transmit analogue video. Its name comes from the fact that the three main video components (brightness data and two colour difference channels) are carried over three separate cables. Accordingly, each individual component input is a set of three connectors. Usually, a built-in cable with RCA connectors (“tulip”) is used for connection, while the cables for component and composite (see below) interfaces are quite interchangeable.

The component interface stands out for its high signal transmission quality: splitting the video into three separate channels significantly reduces distortion compared to the same composite format, and the bandwidth is comparable to the above-described HDMI and allows you to work even with HD video. However, a component connection does not provide audio, and you will need to use a separate cable for this purpose.

As for the quantity, the presence of several inputs allows you to connect several signal sources to the receiver at once with the corresponding outputs and switch between them through software settings without fiddling with switching cables.

RCA

The number of analogue stereo RCA outputs provided in the design of the AV receiver.

By itself, the RCA connector (colloquially — "tulip") can be used in different interfaces. However, in this particular case, we are talking about a linear audio output that is responsible for an analogue audio signal. RCA is the most popular connector used in modern audio equipment for such outputs. In this case, we can talk about both standard outputs for connecting speakers, and about REC connectors designed to connect a recording device to the receiver and differ in a constant signal level. (however, there is rarely more than one such output). In addition, preamplifier outputs are also taken into account here.

Note that connectors of this type are usually counted in pairs; in other words, one output consists of two RCA connectors. This is due to the fact that in this case only one channel of analogue audio can be transmitted over one wire; accordingly, two RCA jacks are required for stereo transmission.

Several RCA outputs allow you to connect several sets of acoustics to the receiver at the same time — for example, to broadcast sound in several rooms at once or to record sound in parallel with listening to it.
Onkyo TX-SR373 often compared
Onkyo TX-SR343 often compared