Car Service Station Equipment Powertec

A set of four elasticated wheel covers, manufactured to fit over 13", 14" and 15" tyres to protect them while paint spraying work is carried out.

A flexible sanding file that can be used for concave, convex and flat sanding. With 14 holes and dust extractor connection point for easy dust removal in operation.

Simple to use and suitable for use on a wide range of vehicles, this extending rear hatch support is used to support the rear hatch and hold it at a suitable angle/height while it is being painted or repaired. Featuring able to extend from 720mm to 1840mm, this simple, yet useful device can be used on hatchbacks, estates, saloons and even some SUV's.

This Duck Bill Clamp from Power-Tec is ideal for use in hard to reach areas where regular sized clamps are not able to fit. With a 30mm wide jaw, 65mm reach and 3 Ton capacity, this clamp may be slim, but it is just as capable as other clamps.

This adjustable double aperture restraint from Power-Tec helps to avoid distortion to door openings and roof linings on vehicles while repair work is being carried out. Manufactured from tough, durable heat treated steel and fully adjustable, these are suitable for use on a wide range of vehicles. A must have repair tool.

Part of the Power-TEC door repair range of toolsEliminate damage to bodywork when adjusting hingesAdjustable 0-42 mmQuick and easy to install and adjust to exact size of hinge.Greater control and adjustment in any directionNo need for multiple heads. Fits all sizes of hinge

A large curved sanding file, made to be used with the Power-Tec 390mm sanding block. Ideal for quick and effective sanding of large contoured areas.

Quick and easy to fit adaptor, designed to convert the Power-Tec flexible sanding file into a large curved file for contour sanding of large areas.

With 125mm x 65mm reach, 6 ton pulling capacity and a slim clamp leg for working over various obstacles that can be faced during automotive bodywork pulling applications, the CamLok clamp from Power-Tec is ideal for pulling work on vehicle chassis and other areas.

This simple to use, time & money saving tool is used to restore the natural contours of body panels by raising or lowering the defect as close as possible to the original surface, minimising the amount of removal during panel preparation.

A durable aluminium and steel plate body file holder and file combination, that can be bent to convex and concave angles, or left flat, perfect for use on a wide range of body panels, curved or flat.

Lightweight bit hook manufactured to be used with the Power-Tec AiroPower system.

A 9 piece kit containing an array of tools used to open doors and hatches on vehicles in emergency situations. Includes strips for windows and wire tools that allow the user to skillfully open doors and hatches on European and Japanese cars.

A handheld metal roller designed for smoothing the melted plastic during the plastic welding/repair process. Ideal for use with nitrogen or compressed air plastic welders.Metal pressure roller, with a plastic handle, to help finish plastic repairs.Roller dimensions: 35mm (width) x 25mm (diameter).Overall length: 230mm.Also supplied as part of Power-TEC plastic welding kits, including Part Nos. 92446, 92229, 92517 & 92452.Scraper for cleaning plastic parts also available, please see Part No. 92668.

More and more vehicles require the vehicle ride height to be checked and set to ensure that modern driver aids (ADAS etc.) function correctly. The Power-TEC 92666 ride height gauge can be used to measure the ride height either by measuring under the vehicle sills or even under the centre of the vehicle without crawling under the car.Use with the car on level ground or on scale/turning pads.Measure from 51mm to 350mm (imperial scale also shown). Measure from almost any area under the car.Magnetic tape measure head allows measurement to be made while adjusting the ride height.For best results measure at identical points either side of the vehicles (4 measurements).Equivalent to OEM Tesla 1071271-00-A.…

The Power-TEC Denibbing Tool is a fast and effective way to remove paint and clear coat imperfections, without the need for respraying. Its clever design enables the user to remove trapped dust particles, small dirt build ups, or other irregularities quickly and easily.Designed to remove small clear coat defects.Precision cut sharp edges, designed to remove dust particles & give uniform results.Manufactured from tungsten steel.Recommended for use with shim-masks, please see Part No. 92439.Supplied complete with carry cord & plastic storage case.

This paintless dent repair tool uses magnetic induction heating to remove soft edged dents like hail damage and carpark dings on automotive bodywork panels, quickly and easily, without damaging the paintwork. It features adjustable time setting and power controls, which can be easily viewed on the digital display, and is supplied in a robust carry case for safe storage.Mains-powered induction heater designed to remove dings & soft dents on steel panels in only 30 seconds.230v single phase, 1.8A, 400W output power.Power cable length: 1.5m; Repair head cable length: 3m.Features adjustable time control (1 sec to 5 sec) & adjustable power control (10% to 100%), with an easy to read digital display.…

Mains-powered 60w airless plastic welder, fitted with a 1.2m lead & 230V 13 amp 3 pin BS plug.Supplied with 2 welding tips & safety stand for use when hot.Suitable for repairing thermoset plastics like PUR (Polyurethane) with ease. Ideal for use on bumper repairs etc.Temperature range: 350C (662F) to 400C (752F).CE & RoHS compliant. PUR (Polyurethane) rod available separately, please see Part No. 91841.

An additional anchoring plate / suction pad specifically for use with the Power-TEC Pulling Tower (Part No. 92657), to allow for the tower to be used in a vertical position such as pulling down on damaged floor pans or sills. The 280 x 330mm plate features a vulcanised rubber pad and is held onto the ground using the workshop air supply, allowing it to be used anywhere on the workshop floor without the need to drill in any anchor points or fixings.Designed for use with Power-TEC Pulling Tower (Part No. 92657).Provides an additional anchor point to counterbalance the tower to be used vertically.Dimensions: 280 x 330mm.Attaches via pneumatic suction, from the workshop air supply, therefore no …

A steel extension pole specifically for use with the Power-TEC Pulling Tower (Part No. 92657), which adds an additional 700mm with 7 adjustable height positions and allows the tower to be used on truck and van roof panel repairs.Designed for use with Power-TEC Pulling Tower (Part No. 92657).Increases tower height to 2200mm to allow truck & van roof repairs.Length: 700mm.Features 7 height positions.Additional Pulling Tower accessories also available, please see Part No. 92660 (Vertical Pull Kit).

A fast, easy to install pulling tower with a height adjustable mechanical hoist (extension pole available to raise height for commercial vehicles 92659). Ideal for use on steel and aluminium panel repair. Designed to reach a pulling traction force up to 550kg, it is counterbalanced by an anchoring plate / suction pad, which features a vulcanised rubber pad and is held onto the ground using the workshop air supply, allowing it to be used anywhere on the workshop floor without the need to drill in any anchor points or fixings. It is supplied with a claw hook for use with weld on squiggly wire, Miracle System bits, glue pads, weld-on tack & pull plates and various other applications.Portable pulling …

A sprung holding tool and adjustable bracket for use with Power-TEC Part Nos. 92652 and 92653 designed to push out on the internal surfaces of body parts and trim to hold them in position during the painting process.An adjustable bracket with a sprung holding grip.Suitable for holding all items that have to be held from within, such as mirror housings.Designed for use with Power-TEC Easyflex Universal Panel Stand (Part No. 92652) & Multiflex Bumper Stand (Part No. 92653).High quality steel construction. Made in Denmark.Additional brackets & accessories available separately, please see Part Nos. 92654 (Trim & Spoiler Kit), 92655 (Snapgrip).

A fully adjustable additional bracket for use with Power-TEC Part Nos. 92652 and 92653 that features an integral sprung grip, designed to hold smaller parts and trim during the painting process.An adjustable bracket with an integral sprung grip.Suitable for holding small parts during painting.Designed for use with Power-TEC Easyflex Universal Panel Stand (Part No. 92652) & Multiflex Bumper Stand (Part No. 92653).High quality steel construction. Made in Denmark.Additional brackets & accessories available separately, please see Part Nos. 92654 (Trim & Spoiler Kit), 92656 (Press Out Holding Tool).

An easy to use bumper stand, for use during preparation and painting. It features four adjustable arms, including two with integral plier grips, to support and hold the bumper, which also allow the bumper to be both rotated front to back and swivelled sided to side for access. The slim-line design also features a fold-away leg making it easy to stow when not in use.Adjustable bumper stand, with integral plier grips, rotates & swivels through 90 to allow access during preparation & painting.Two wheel fold-away design, making it easy to store when not in use.High quality steel construction. Maximum load capacity: 100kg.Made in Denmark.Additional brackets & accessories available separately, please …