Submersible (Drainage) Pumps

The DG Blue Professional is a submersible pump is suitable for pumping water polluted with suspended solid particles. The cast iron vortex impeller gives great performance in terms of flow rate and head, including integral free passage of up to 50mm. Applications include: Cellars and basements Industrial schemes Final effluent Nuisance water Hire fleets Agriculture /farming Sewage and treatment works Civil construction

The DG Blue Professional is a submersible pump is suitable for pumping water polluted with suspended solid particles. The cast iron vortex impeller gives great performance in terms of flow rate and head, including integral free passage of up to 50mm. Applications include: Cellars and basements Industrial schemes Final effluent Nuisance water Hire fleets Agriculture /farming Sewage and treatment works Civil construction

The DR Blue Pro is a submersible drainage pump with an open, multi-channel impeller for most soiled water applications. Applications include: Cellars and basements Industrial schemes Final effluent Nuisance water Hire fleets Civil construction

The AP Blue Pro is a sumbersible pump suitable for both domestic and professional applications. The pump has a high-head cast iron impeller and is ideal for clean water, rainwater, seepage water and sandy or muddy water containing small particles no larger than 6mm in suspension. Applications include: Domestic and industrial use Agricultural and farming Sewage and treatment works Irrigation

The AP Blue Pro is a sumbersible pump suitable for both domestic and professional applications. The pump has a high-head cast iron impeller and is ideal for clean water, rainwater, seepage water and sandy or muddy water containing small particles no larger than 6mm in suspension. Applications include: Domestic and industrial use Agricultural and farming Sewage and treatment works Irrigation

For heavy and continuous duty pumping of water levels down to 1mm, with a rubber moulded electronic level probe switch. Ideal for automatic control of water levels on flat roofs, car-parks, concrete shuttering, lift-shafts, basements and during incidents of flooding. Power saving as will only operate when probes sense water (not run continuously), then operate for 1 minute after level drops below probes, but continue pumping if probes touch water again during this time. Start level depth of water is approximately 170mm, but probe extensions to turn on approximately at depths of 70mm (70mm kit) and about 5mm (170mm kit) are an optional extra. Pumps water with sand and silt in suspension.

For heavy and continuous duty pumping of water levels down to 1mm, with a rubber moulded electronic level probe switch. Ideal for automatic control of water levels on flat roofs, car-parks, concrete shuttering, lift-shafts, basements and during incidents of flooding. Power saving as will only operate when probes sense water (not run continuously), then operate for 1 minute after level drops below probes, but continue pumping if probes touch water again during this time. Start level depth of water is approximately 170mm, but probe extensions to turn on approximately at depths of 70mm (70mm kit) and about 5mm (170mm kit) are an optional extra. Pumps water with sand and silt in suspension. Made

The DR Blue Pro is a submersible drainage pump with an open, multi-channel impeller for most soiled water applications. Applications include: Cellars and basements Industrial schemes Final effluent Nuisance water Hire fleets Civil construction

The DR Blue Pro is a submersible drainage pump with an open, multi-channel impeller for most soiled water applications. Applications include: Cellars and basements Industrial schemes Final effluent Nuisance water Hire fleets Civil construction

The FloodMate 2 is an emergency pumping kit for defending property from low level flooding. This set includes a 230V, 480 Watt submersible pump (model LSC1.4 capable of up 70 litres per minute, through 25mm 1" hose, over 30 metres of level ground). All the contents are supplied in a sturdy, easy-to-carry and store, case with lid and the included pump is designed to operate constantly, pumping away minimal amounts of flood water down to a level of 1mm. The hoses are light, easy to position and feature quick connections to enable fast deployment in an emergency. Initial priming of the pump with water is required before starting, it will pump water down to 1mm and can run dry for long periods

For heavy and continuous duty pumping of water levels down to 1mm, with a rubber moulded electronic level probe switch. Ideal for automatic control of water levels on flat roofs, car-parks, concrete shuttering, lift-shafts, basements and during incidents of flooding. Power saving as will only operate when probes sense water (not run continuously), then operate for 1 minute after level drops below probes, but continue pumping if probes touch water again during this time. Start level depth of water is approximately 170mm, but probe extensions to turn on approximately at depths of 70mm (70mm kit) and about 5mm (170mm kit) are an optional extra. Pumps water with sand and silt in suspension. Made

For heavy and continuous duty pumping of water levels down to 1mm, with a rubber moulded electronic level probe switch. Ideal for automatic control of water levels on flat roofs, car-parks, concrete shuttering, lift-shafts, basements and during incidents of flooding. Power saving as will only operate when probes sense water (not run continuously), then operate for 1 minute after level drops below probes, but continue pumping if probes touch water again during this time. Start level depth of water is approximately 170mm, but probe extensions to turn on approximately at depths of 70mm (70mm kit) and about 5mm (170mm kit) are an optional extra. Pumps water with sand and silt in suspension.

Ideal for pumping waste water in septic tanks, sewage plants, factory processes and circulating water in ponds and water features. Pumps large soft solids in suspension. Made from tough engineering plastic and stainless steel. Low energy motors have overload protection. Built in handle. Fitted with an integral female BSP outlet, for pipe connection, and 10m of heavy duty H07RNF cable. Automatic - will turn on at 607mm and off at 115mm with some adjustment to turn on lower.

Ideal for pumping waste water in septic tanks, sewage plants, factory processes and circulating water in ponds and water features. Pumps large soft solids in suspension. Made from tough engineering plastic and stainless steel. Low energy motors have overload protection. Built in handle. Fitted with an integral female BSP outlet, for pipe connection, and 10m of heavy duty H07RNF cable. Automatic - will turn on at 607mm and off at 115mm with some adjustment to turn on lower.

Ideal for pumping waste water in septic tanks, sewage plants, factory processes and circulating water in ponds and water features. Pumps large soft solids in suspension. Made from tough engineering plastic and stainless steel. Low energy motors have overload protection. Built in handle. Fitted with an integral female BSP outlet, for pipe connection, and 10m of heavy duty H07RNF cable. Selectable manual or auto mode - auto will turn on at 607mm and off at 115mm with some adjustment to turn on lower.

RX-VORTEX Submersible pump in stainless steel for Dirty Water INSTALLATION AND USE The RX-VORTEX series pumps are suitable for use with dirty water. The design solutions that have been adopted, such as the complete cooling of the motor, guarantee the reliability of the pump. They are suitable for use in domestic applications such as for discharging dirty water containing suspended solids. FEATURES Liquid type: dirty water Uses: domestic, civil APPLICATIONS: drainage, dirty water - slightly solid particles, emptying tanks. Typology: submersible Family: submersible pumps APPLICATION LIMIT: Temperature of the liquid to +40 °C 10 m maximum immersion depth with a sufficiently long power cable

The Select Brand Arvex/S (230V) is ideal for the pumping of chemicals that are of a mildly aggressive nature, which would normally corrode a lower grade of metal and plastic components found in a traditional pump. This pump is suitable for use with seawater and saltwater and they are also suitable for use with light chemicals. This model can pump small soft solids in suspension, but is not suitable for ponds or water features. This unit includes a 10 metre power cable, allowing for extra working room. The maximum liquid temperature is 50°C (25°C if part submerged) and this unit also benefits from a built in handle and included hose connector. Completing this product is a 316 grade

The Arvex/S (230V) is ideal for the pumping of chemicals that are of mildly aggressive nature, which would normally corrode a lower grade of metal and plastic components found in a traditional pump. This pump is suitable for use with sea and salt water and they are also suitable for use with light chemicals. This model can pump small soft solids in suspension but is not suitable for ponds or water features, but the included power cable is 10 metres allowing for extra working room. The maximum liquid temperature is 50°C (25°C if part submerged) and this unit also benefits from a built in handle and included hose connector. Completing this product is a 316-grade (1.4401) pressed

The Arvex/S (400V) is ideal for the pumping of chemicals that are of mildly aggressive nature, which would normally corrode a lower grade of metal and plastic components found in a traditional pump. This pump is suitable for use with sea and salt water and they are also suitable for use with light chemicals. This model can pump small soft solids in suspension, but is not suitable for ponds or water features. This unit includes a 10 metre power cable, allowing for extra working room. The maximum liquid temperature is 50°C (25°C if part submerged) and this unit also benefits from a built in handle and included hose connector. Completing this product is a 316-grade (1.4401) pressed

The FloodMate 2 is an emergency pumping kit for defending property from low level flooding. This set includes a 110V, 480 Watt submersible pump (model LSC1.4 which is capable of up 70 litres per minute, through 25mm 1" hose, over 30 metres of level ground). All the contents are supplied in a sturdy, easy-to-carry and store, case with lid and the included pump is designed to operate constantly, pumping away minimal amounts of flood water down to a level of 1mm. The hoses are light, easy to position and feature quick connections to enable fast deployment in an emergency. Initial priming of the pump with water is required before starting, it will pump water down to 1mm and can run dry for

The Liberator Vortex is an extension to the Liberator range of submersible dewatering pumps. This model has high resistance to liquids containing sand and gravel, with a motor frequency of 50Hz. This unit is able to withstand harsh conditions particularly amongst the abrasive material in sludge content. It is suitable for a range of different applications, including emergency dewatering and is completed with TT Pumps high quality build and design for excellent durability.

The Liberator Vortex is an extension to the Liberator range of submersible dewatering pumps. This model has high resistance to liquids containing sand and gravel, with a motor frequency of 50Hz. This unit is able to withstand harsh conditions particularly amongst the abrasive material in sludge content. It is suitable for a range of different applications, including emergency dewatering and is completed with TT Pumps high quality build and design for excellent durability.

The Liberator Vortex is an extension to the Liberator range of submersible dewatering pumps. This model has high resistance to liquids containing sand and gravel, with a motor frequency of 50Hz. This unit is able to withstand harsh conditions particularly amongst the abrasive material in sludge content. It is suitable for a range of different applications, including emergency dewatering and is completed with TT Pumps high quality build and design for excellent durability.