Submersible (Drainage) Pumps Tsurumi

Ideal for heavy duty and continuous pumping on building sites, ditches, footings, processes etc. Fitted with stirring device to assist pumping of sand and silt in suspension. Made from cast aluminium and iron. Rubber filter base is impact resistant. Built in handle. Hose connector and 10m of heavy duty H07RNF cable included. Selectable manual or auto mode - turns pump off when water level drops and protect from dry running. Residue plate kit will convert HS2.4S to a puddle pump, to pump water right down to 10mm. Steel coated with rubber, it is easy to fit and take off.

The HSD.55S is a lightweight and robust single-phase submersible drainage pump, with an agitator and impeller constructed from chromium iron to reduce clogging and increase wear resistance when pumping particulate-contaminated water, sludge and bentonite. The hydraulic design of this pump features a double mechanical seal with an oil lifter, for positive seal lubrication in any operating position, not only that, but the high-performance motor enables long periods of operation while partially submerged. Supplied with a pendant float switch, for automatic operation. Built for use and designed for long life application.

Ideal for heavy and continuous duty pumping on building sites, ditches, footings, processes etc. Used extensively in tool hire. Pumps water with sand and silt in suspension. Can run for long periods while pumping minimal water and in any position. Made from tough steel and rubber. Built in handle. 10m of heavy duty H07RNF cable. Hose connector adjustable to two positions to avoid hose kinking. Selectable manual or auto mode - turns pump off when water level drops and protect from dry running.

Ideal for heavy and continuous duty pumping on building sites, industrial processes, tunneling,mines and quarries . Pump water with sand and silt in suspension. Can run for long periods while pumping minimal water and in any position. Made from heavy duty cast iron, tough steel and ductile iron. Built in handle. 20m of heavy duty H07RNF cable. Supplied with two hose connectors: spigot and mBSP Both adjustable to two positions to avoid hose kinking and supplied as Selectable manual or auto sensor mode - turns pump off when water level drops and protect from dry running.

For heavy and continuous duty pumping of water levels down to 1mm, with a rubber moulded electronic level probe switch. Ideal for automatic control of water levels on flat roofs, car-parks, concrete shuttering, lift-shafts, basements and during incidents of flooding. Power saving as will only operate when probes sense water (not run continuously), then operate for 1 minute after level drops below probes, but continue pumping if probes touch water again during this time. Start level depth of water is approximately 170mm, but probe extensions to turn on approximately at depths of 70mm (70mm kit) and about 5mm (170mm kit) are an optional extra. Pumps water with sand and silt in suspension. Made

Ideal for heavy and continuous duty pumping on building sites, industrial processes, tunneling,mines and quarries . Pump water with sand and silt in suspension. Can run for long periods while pumping minimal water and in any position. Made from heavy duty cast aluminium (for improved portability) tough steel, ductile iron and rubber. Built in handle. 20m of heavy duty H07RNF cable (10m on 0.75kW). Supplied with two hose connectors: spigot and mBSP Both adjustable to two positions to avoid hose kinking.

Ideal for heavy and continuous duty pumping on building sites, ditches, footings, processes etc. Used extensively in tool hire. Pumps water with sand and silt in suspension. Can run for long periods while pumping minimal water and in any position. Made from tough steel and rubber. Built in handle. 10m of heavy duty H07RNF cable. Hose connector adjustable to two positions to avoid hose kinking. Selectable manual or auto mode - turns pump off when water level drops and protect from dry running.

For heavy and continuous duty pumping of water levels down to 1mm. Ideal for draining water on flat roofs, car-parks, concrete shuttering, lift-shafts and basements. For use in tool-hire, on building sites, flood defence and general drainage of building sites, Pumps water with sand and silt in suspension. Can run for long periods while pumping minimal water and in any position. Made from tough steel and rubber. Built in handle. 10m of heavy duty H07RNF cable. Hose connector adjustable to two positions to avoid hose kinking.

The FloodMate 2 is an emergency pumping kit for defending property from low level flooding. This set includes a 230V, 480 Watt submersible pump (model LSC1.4 capable of up 70 litres per minute, through 25mm 1" hose, over 30 metres of level ground). All the contents are supplied in a sturdy, easy-to-carry and store, case with lid and the included pump is designed to operate constantly, pumping away minimal amounts of flood water down to a level of 1mm. The hoses are light, easy to position and feature quick connections to enable fast deployment in an emergency. Initial priming of the pump with water is required before starting, it will pump water down to 1mm and can run dry for long periods

Ideal for heavy duty and continuous pumping on building sites, ditches, footings, processes etc. Fitted with stirring device to assist pumping of sand and silt in suspension. Made from cast aluminium and iron. Rubber filter base is impact resistant. Built in handle. Hose connector and 10m of heavy duty H07RNF cable included. Selectable manual or auto mode - turns pump off when water level drops and protect from dry running. Residue plate kit will convert HS2.4S to a puddle pump, to pump water right down to 10mm. Steel coated with rubber, it is easy to fit and take off.

Ideal for heavy and continuous duty pumping on building sites, industrial processes, tunneling, mines and quarries . Pump water with sand and silt in suspension. Can run for long periods while pumping minimal water and in any position. Made from heavy duty cast aluminium (for improved portability) tough steel, ductile iron and rubber. Built in handle. 20m of heavy duty H07RNF cable (10m on 0.75kW). Supplied with two hose connectors: spigot and mBSP Both adjustable to two positions to avoid hose kinking and supplied as Selectable manual or auto sensor mode - turns pump off when water level drops and protect from dry running.

Ideal for heavy duty and continuous pumping on building sites, ditches, footings, processes etc. Fitted with stirring device to assist pumping of sand and silt in suspension. Made from cast aluminium and iron. Rubber filter base is impact resistant. Built in handle. Hose connector and 10m of heavy duty H07RNF cable included. Selectable manual or auto mode - turns pump off when water level drops and protect from dry running. Residue plate kit will convert HS2.4S to a puddle pump, to pump water right down to 10mm. Steel coated with rubber, it is easy to fit and take off.

Ideal for heavy and continuous duty pumping on building sites, industrial processes, tunneling, mines and quarries. Pump water with sand and silt in suspension. Can run for long periods while pumping minimal water and in any position. Made from heavy duty cast iron, tough steel and ductile iron. Built in handle. 20m of heavy duty H07RNF cable. Supplied with two hose connectors: spigot and mBSP Both adjustable to two positions to avoid hose kinking and supplied as Selectable manual or auto sensor mode - turns pump off when water level drops and protect from dry running.

Ideal for pumping water from flooded areas, cellars, sumps etc. Pumps large soft solids in suspension. Not suitable for ponds or water features. Made from tough engineering plastic and stainless steel. Low energy 150w motor has overload protection. Built in handle. Hose connector included and 10m of heavy duty H07RNF cable. Selectable manual or auto mode - auto will turn on at 285mm and off at 100mm and work in confined areas.

Ideal for pumping waste water in septic tanks, sewage plants, factory processes and circulating water in ponds and water features. Pumps large soft solids in suspension. Made from tough engineering plastic and stainless steel. Low energy motors have overload protection. Built in handle. Fitted with an integral female BSP outlet, for pipe connection, and 10m of heavy duty H07RNF cable. Automatic - will turn on at 607mm and off at 115mm with some adjustment to turn on lower.

Ideal for heavy and continuous duty pumping on building sites, industrial processes, tunneling,mines and quarries . Pump water with sand and silt in suspension. Can run for long periods while pumping minimal water and in any position. Made from heavy duty cast iron, tough steel and ductile iron. Built in handle. 20m of heavy duty H07RNF cable. Supplied with two hose connectors: spigot and mBSP Both adjustable to two positions to avoid hose kinking and supplied as Selectable manual or auto sensor mode - turns pump off when water level drops and protect from dry running.

The 50PNI2 is a light and compact automatic pump with an energy efficient motor and integral anti-airlock valves. It feature a dual control float-switch which enables manual and automatic operation. This switch is also adjustable to enable individual setting of on and off levels. The float is bell shaped and small, which make these pumps suited to applications where a sump is narrow, that require precise level control or where a traditional pendant type float’s operation could be fouled. Liquid paraffin is used for the lubrication oil, which enables use in food processing and aquaculture. They are not recommended for ponds or water features.

For heavy and continuous duty pumping of water levels down to 1mm. Ideal for draining water on flat roofs, car-parks, concrete shuttering, lift-shafts and basements. For use in tool-hire, on building sites, flood defence and general drainage of building sites, Pumps water with sand and silt in suspension. Can run for long periods while pumping minimal water and in any position. Made from tough steel and rubber. Built in handle. 10m of heavy duty H07RNF cable. Hose connector adjustable to two positions to avoid hose kinking.

Ideal for heavy duty and continuous pumping on building sites, ditches, footings, processes etc. Fitted with stirring device to assist pumping of sand and silt in suspension. Made from cast aluminium and iron. Rubber filter base is impact resistant. Built in handle. Hose connector and 10m of heavy duty H07RNF cable included. Residue plate kit will convert HS2.4S to a puddle pump, to pump water right down to 10mm. Steel coated with rubber, it is easy to fit and take off.

The HSD.55S is a lightweight and robust single-phase submersible drainage pump, with an agitator and impeller constructed from chromium iron to reduce clogging and increase wear resistance when pumping particulate-contaminated water, sludge and bentonite. The hydraulic design of this pump features a double mechanical seal with an oil lifter, for positive seal lubrication in any operating position, not only that, but the high-performance motor enables long periods of operation while partially submerged. Built for use and designed for long life application.

Ideal for heavy duty and continuous pumping on building sites, ditches, footings, processes etc. Fitted with stirring device to assist pumping of sand and silt in suspension. Made from cast aluminium and iron. Rubber filter base is impact resistant. Built in handle. Hose connector and 10m of heavy duty H07RNF cable included. Selectable manual or auto mode - turns pump off when water level drops and protect from dry running. Residue plate kit will convert HS2.4S to a puddle pump, to pump water right down to 10mm. Steel coated with rubber, it is easy to fit and take off.

Ideal for heavy and continuous duty pumping on building sites, industrial processes, tunneling,mines and quarries . Pump water with sand and silt in suspension. Can run for long periods while pumping minimal water and in any position. Made from heavy duty cast aluminium (for improved portability) tough steel, ductile iron and rubber. Built in handle. 20m of heavy duty H07RNF cable (10m on 0.75kW). Supplied with two hose connectors: spigot and mBSP Both adjustable to two positions to avoid hose kinking.

Ideal for pumping water from flooded areas, cellars, sumps etc. Pumps small soft solids in suspension. Not suitable for ponds or water features. Made from tough engineering plastic and stainless steel. Low energy 150 watt motor has overload protection. Built in handle. 10m of heavy duty H07RNF cable included.

Ideal for heavy and continuous duty pumping on building sites, industrial processes, tunneling,mines and quarries . Pump water with sand and silt in suspension. Can run for long periods while pumping minimal water and in any position. Made from heavy duty cast aluminium (for improved portability) tough steel, ductile iron and rubber. Built in handle. 20m of heavy duty H07RNF cable (10m on 0.75kW). Supplied with two hose connectors: spigot and mBSP Both adjustable to two positions to avoid hose kinking and supplied as Selectable manual or auto sensor mode - turns pump off when water level drops and protect from dry running.