Other for Construction

The Moore & Wright 966 Series Traditional External Micrometer has a blue textured frame finish with tungsten carbide measuring faces. The 'speeder' type ratchet, locking lever and adjusting key make this micrometer easy to use. It has a 6.5mm spindle diameter. The micrometers are manufactured to BS870, DIN 863/1, ISO 361 standards. Supplied in a case.The 1966M/50 Traditional External Micrometer has the following specification: Micrometer Range: 25-50mm.Measuring Faces: Flatness: 0.001mm, Parallelism: 0.003mm, Accuracy: 0.003mm.Resolution: 0.01mm.Additional Information:• Micrometer Type: External• Metric/Imperial: Metric• Min. Measurement (mm): 25• Max. Measurement (mm): 50• …

The Moore & Wright 900 Series Internal Micrometers comprise of a measuring head, a set of extension rods and a spacing collar to facilitate alternative measuring ranges. These models (901, 902 & 903) have detachable extension handles. All models supplied in a fitted case. These 900 Series Internal Micrometers conform to BS959 Standards.The Moore & Wright Internal Micrometer 903 Internal Micrometer has the following specification: Range: 2-12in.Head Range: 0.50in.Additional Information:• Micrometer Type: Internal• Metric/Imperial: Imperial• Min Measurement (in): 2• Max. Measurement (in): 12• Graduation (in): 0.001

The Moore & Wright Engineer's Levels have a precision ground cast base with a V-groove for location on cylindrical work. Each level is fitted with a main, cross and plumb vial and the main vial is protected by a rotating shroud. The solution in the vials maintains colour and fluidity under all workshop conditions and the main vial has a sensitivity of 1 minute.The Moore & Wright ELS Engineer's Levels have the following specification: Length: 165mm (6.5in).Width: 34mm (1.34in).Height: 46mm (1.81in).Resolution: 0.3mm per metre (0.0035in per foot).Additional Information:• Size (mm): 165• Size (in): 6.1/2• Resolution (mm): 0.3• Resolution (in): 0.0035

The Moore & Wright CSM Precision Rules are fully hardened and tempered precision rules with deeply etched graduations on both sides for ease of reading and long life. Theseare rules specifically designed for use with the Combination Sets (MAWCSM300 & MAWCSME12).The Moore & Wright CSRM600 is a 600mm rule is perfect for use with the combination sets and is graduated on both sides. Measurements: mm and 0.5mm on both sides; numbered every 10mm. PLEASE NOTE This is ONLY the Rule.Additional Information:• Gauge Type: Rule

The Moore & Wright Spring Joint External Calipers have a bow spring to ensure uniform tension over the working range. They have a centrally mounted adjustment screw offering a finer setting than firm joint type calipers. These spring joint external calipers conform to BS3123 standards.1 x Moore & Wright 524R Spring Joint External Calipers 100mm (4in) in Retail Packaging.Additional Information:• Spring Type: External• Size (mm): 100• Size (in): 4

The Moore & Wright Spring Joint External Calipers have a bow spring to ensure uniform tension over the working range. They have a centrally mounted adjustment screw offering a finer setting than firm joint type calipers. These spring joint external calipers conform to BS3123 standards.1 x Moore & Wright 526R Spring Joint External Calipers 150mm (6in) in Retail Packaging.Additional Information:• Spring Type: External• Size (mm): 150• Size (in): 6

The Moore & Wright Traditional External Micrometer has a pearl chrome plated frame with insulation pads, tungsten carbide measuring faces and a tapered bow frame. The 'speeder' type ratchet, locking lever and adjusting key make this micrometer easy to use. It has a 6.5mm spindle diameter. The micrometers are manufactured to BS870, DIN 863/1, ISO 361 standards. Supplied in plastic pocket case. The 1961M Traditional External Micrometer has the following specification: Micrometer Range: 0-25mm. Measuring Faces: Flatness: 0.001mm, Parallelism: 0.003mm, Accuracy: 0.003mm.Resolution: 0.01mm.Additional Information:• Micrometer Type: External• Metric/Imperial: Metric• Min. Measurement …

The Moore & Wright Traditional External Micrometer has a blue textured frame finish with tungsten carbide measuring faces and a tapered bow frame. The 'speeder' type ratchet, locking lever and adjusting key make this micrometer easy to use. It has a 6.5mm spindle diameter. The micrometers are manufactured to BS870, DIN 863/1, ISO 361 standards. Supplied in plastic pocket case.The 1965 Traditional External Micrometer has the following specification: Micrometer Range: 0-1in. Measuring Faces: Flatness: 0.00005in, Parallelism: 0.0001in, Accuracy: 0.0001in.Resolution: 0.001in.Additional Information:• Micrometer Type: External• Metric/Imperial: Imperial• Min. Measurement (mm): 0• …

The Moore & Wright 890M Fixed Type Depth Micrometer has a fixed depth rod with a 6.5mm diameter. It is fitted with a 'speeder' type ratchet and a lock screw for added user convenience. Conforms to BS 6468:1984. Specification: Base Length: 63.5mm (2.1/2in)Range: 0-25mmResolution: 0.01mmAdditional Information:• Micrometer Type: Depth• Metric/Imperial: Metric• Min. Measurement (mm): 0• Max. Measurement (mm): 25• Graduation (mm): 0.01

The Moore & Wright 900 Series Internal Micrometers comprise of a measuring head, a set of extension rods and a spacing collar to facilitate alternative measuring ranges. These models (901, 902 & 903) have detachable extension handles. All models supplied in a fitted case. These 900 Series Internal Micrometers conform to BS959 Standards.The Moore & Wright Internal Micrometer 901M Internal Micrometer has the following specification: Range: 25-55mm.Head Range: 5mm.Additional Information:• Micrometer Type: Internal• Metric/Imperial: Metric• Min. Measurement (mm): 25• Max. Measurement (mm): 55• Graduation (mm): 0.01

The Moore & Wright 900 Series Internal Micrometers comprise of a measuring head, a set of extension rods and a spacing collar to facilitate alternative measuring ranges. These models (901, 902 & 903) have detachable extension handles. All models supplied in a fitted case. These 900 Series Internal Micrometers conform to BS959 Standards.The Moore & Wright Internal Micrometer 903M Internal Micrometer has the following specification: Range: 50-310mm.Head Range: 10mm.Additional Information:• Micrometer Type: Internal• Metric/Imperial: Metric• Min. Measurement (mm): 50• Max. Measurement (mm): 310• Graduation (mm): 0.01

The Moore & Wright Firm Joint Inside Calipers are manufactured from polished tool steel and have a large headed nut and screw assembly to provide a firm and rigid friction joint, with no play. The sizes listed are the effective leg length which is measured from the joint assembly. The Firm Joint Inside Calipers are manufactured to BS3123 standards. Note: Firm joint caliper capacities are generally 1/3 greater than the effective leg length.1 x Moore & Wright 3306R Firm Joint Inside Caliper 150mm (6in) in Retail Packaging.Additional Information:• Caliper Type: Internal• Size (mm): 150• Size (in): 6

The Moore & Wright Firm Joint Jenny Calipers are manufactured from polished tool steel and have a large headed nut and screw assembly that provides a firm and rigid friction joint, with no play. The leg which holds the round adjustable hardened point is offset and model 341 has a locating spur on the straight leg. The sizes listed are the effective leg length which is measured from the joint assembly. Note: firm joint caliper capacities are generally 1/3 greater than the effective leg length.1 x Moore & Wright 336-6R Firm Joint Jenny Caliper 150mm (6in) in Retail Packaging.Additional Information:• Jenny Type: Firm Joint• Size (mm): 150• Size (in): 6

The Moore & Wright Firm Joint Outside Calipers are manufactured from polished tool steel and have a large headed nut and screw assembly providing a firm and rigid friction joint, with no play. The sizes listed are the effective leg length which is measured from the joint assembly. The Firm Joint Outside Calipers are manufactured to BS3123 standards. Note: Firm joint caliper capacities are generally 1/3 greater than the effective leg length.1 x Moore & Wright 3316R Firm Joint Outside Calipers 150mm (6in) in Retail Packaging.Additional Information:• Caliper Type: External• Size (mm): 150• Size (in): 6

The Moore & Wright Firm Joint Outside Calipers are manufactured from polished tool steel and have a large headed nut and screw assembly providing a firm and rigid friction joint, with no play. The sizes listed are the effective leg length which is measured from the joint assembly. The Firm Joint Outside Calipers are manufactured to BS3123 standards. Note: Firm joint caliper capacities are generally 1/3 greater than the effective leg length.1 x Moore & Wright 33124 Firm Joint Outside Calipers 600mm (24in)Additional Information:• Caliper Type: External• Size (mm): 600• Size (in): 24

The Moore & Wright CSM Precision Rules are fully hardened and tempered precision rules with deeply etched graduations on both sides for ease of reading and long life. Theseare rules specifically designed for use with the Combination Sets (MAWCSM300 & MAWCSME12).The Moore & Wright CSRME24 is a 600mm/24in rule is perfect for use with the combination sets and is graduated on both sides. Measurements: Metric Graduations: in 0.5mm, numbered every 10mm. Imperial Graduations: 32nds and 64ths numbered every 1/8in. PLEASE NOTE This is ONLY the Rule.Additional Information:• Gauge Type: Rule

The Moore & Wright CSM Precision Sets are supplied with a rule (graduated both sides), Protractor head, Square head and Centre head. The datum faces are fully hardened and ground to resist wear. There is a centrally mounted protractor vial allows unrestricted viewing and the protractor has full 360° scale plate, graduated 0° - 180° - 0°. The protractor is also fitted with a satin chrome scale plate. The precision rules have been fully hardened and tempered with deeply etched graduations on both sides for ease of reading and long life. It has a unique rule clamp that allows positive location and clamping and a clipped corner on rule to maximise capability Square Head offers the …

The Moore & Wright 200 Series MW200-01 Analogue External Micrometer has a hammertone finish frame with an insulated grip, a satin chrome scale and tungsten carbide measuring faces. It has a tapered design for easier access to difficult areas. The micrometer has an adjusting key, locking lever and a constant force ratchet for ease of use. It is manufactured to DIN 863/1 standards, and supplied in plastic case. Specification; Range: 0-25mm.Resolution: 0.01mm.Accuracy: 0.004mm.Additional Information:• Micrometer Type: External• Metric/Imperial: Metric• Min. Measurement (mm): 0• Max. Measurement (mm): 25• Graduation (mm): 0.01

The Moore & Wright 200 Series Digital External Micrometer has a tapered design that provides easier access to difficult areas and a hammertone finished frame with a high quality insulated grip. It also has tungsten carbide measuring faces and a constant force ratchet on the thimble. The large LCD display allows for 4 types of measurement (mm/inch conversion and Absolute/Incremental reading) and a zero setting. The micrometers are manufactured to DIN 863 standards. Specification Range: 0-25mm/0-1in.Resolution: 0.001mm/.00005in.Additional Information:• Micrometer Type: External• Metric/Imperial: Metric & Imperial• Min. Measurement (mm): 0• Max. Measurement (mm): 25• Min …

The Moore & Wright MW279-01A Micrometer Stand is designed for micrometers up to 100mm (4in). It has a painted cast iron base with plastic covered clamping jaws and the angle of the jaws can be adjusted.Additional Information:• Micrometer Type: Stand

The Moore & Wright Spring Dividers are manufactured from polished tool steel and the points are hardened to over 550Hv. The bow spring ensures uniform tension over working range and they are fitted with a centrally mounted adjustment screw. These Spring Dividers comply with BS3123 standards. Note: The nominal size is the distance between the centre of the roller and the working ends of the legs.1 x Moore & Wright 504 Spring Divider 100mm (4in) in Retail Packaging.Additional Information:• Size (mm): 100• Size (in): 4

The Moore & Wright Spring Dividers are manufactured from polished tool steel and the points are hardened to over 550Hv. The bow spring ensures uniform tension over working range and they are fitted with a centrally mounted adjustment screw. These Spring Dividers comply with BS3123 standards. Note: The nominal size is the distance between the centre of the roller and the working ends of the legs.1 x Moore & Wright 506 Spring Divider 150mm (6in) in Retail Packaging.Additional Information:• Size (mm): 150• Size (in): 6

The Moore & Wright Spring Joint Internal Calipers are manufactured from polished tool steel. Their bow spring ensures uniform tension over the working range. The adjustment screw is centrally mounted. These spring joint internal calipers conform to BS3123 standards.1 x Moore & Wright 513R Spring Joint Internal Caliper 75mm (3in) in Retail Packaging.Additional Information:• Spring Type: Internal• Size (mm): 75• Size (in): 3

The Moore & Wright Spring Joint Internal Calipers are manufactured from polished tool steel. Their bow spring ensures uniform tension over the working range. The adjustment screw is centrally mounted. These spring joint internal calipers conform to BS3123 standards.1 x Moore & Wright 516R Spring Joint Internal Caliper 150mm (6in) in Retail Packaging.Additional Information:• Spring Type: Internal• Size (mm): 150• Size (in): 6