Routers & Trimmers

TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. Specifications: • Shank Diameter: 1/2 • Dia Metric: 8 • Dia Imperial: 5/16 • Cut Length Metric: 19 • Overall Length Metric: 65

Two flute straight cutters produce a cleaner finish than the single flute cutters. Suitable for grooving, rebating, mortising and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood, certain hardwoods and hard plastic. Two flutes give a clean finish to cut edges. All cutters above and including 9.5mm diameter, have TCT plunge centre tips.

Recessing cutter will accommodate the Schlegel Aquamac 21 or Exitex Aquatex A10 seal. The cutter is designed for use with the seal in a wiping mode and comes complete with a guide bearing to reduce setting-up time and simplify machining operations. Ref. 334 is MEC mechanical feed only. Specifications: • Shank Diameter: 1/2 • Dia Metric: 46.3 • Dia2 Metric: 34.3 • Cut Length Metric: 2.7/10.3 • Overall Length Metric: 90 • Bearing Dia Metric: 28.6 • Bearing Dia Imperial: 1 1/8

TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. Specifications: • Shank Diameter: 1/2 • Dia Metric: 6 • Dia Imperial: 15/64 • Cut Length Metric: 16 • Overall Length Metric: 69

TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. Specifications: • Shank Diameter: 1/4 • Dia Metric: 6 • Cut Length Metric: 25 • Overall Length Metric: 57

TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. Specifications: • Shank Diameter: 1/2 • Dia Metric: 6 • Cut Length Metric: 25 • Overall Length Metric: 65

The Trend Two Flute Straight Cutters produce a cleaner finish than the single flute cutters. Suitable for grooving, rebating, morticing, drilling and shallow lateral routing cuts such as recessing hinges. Corners will require a final trimming square with a hand chisel or a corner chisel. Suitable for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.

These are made from a single piece of High Speed Steel, ground with a very fine edge. They are only suitable for non abrasive materials, but will give a superior finish in soft timbers. Generally HSS cutters are slightly less expensive than their TC grades, but can be more suitable for certain applications. Suitable for general grooving and rebating. Specifications: • Shank Diameter: 1/4 • Dia Metric: 6.3 • Dia Imperial: 1/4 • Cut Length Metric: 28 • Overall Length Metric: 59

Two flute straight plunging bits General-purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.

A two flute cutters with extra long shanks. Deep grooving, rebating and mortising. Useful for template work when thickness of template restricts depth. Extra care must be taken to avoid breakage. Take more passes than usual, and only cut up to half the diameter of the cutter in one pass. Specifications: • Shank Diameter: 1/4 • Dia Metric: 6.3 • Dia Imperial: 1/4 • Cut Length Metric: 19/19 • Overall Length Metric: 70 • Type or Grade: Two flute

Trend 3/20X1/4TC TCT Two Flute Router Cutter 6.3mm x 16mm The Trend 3/20X1/4TC TCT router cutters are perfect for use on abrasive materials such as chipboard, MDF & plywood. The two flutes give a clean finish to cut edges and the tungsten carbide tips ensure long life and maximum durability. Features:
- Designed for the most abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics
- Two flutes give a clean finish to cut edges
- For routing and profiling natural timbers and man-made boards
- Suitable for most makes of router Specification:
- D: 1/4 inch
- D: 6.3 mm
- C: 16 mm
- OL: 47 mm
- Shank Diameter: 1/4 inch…

TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. Specifications: • Shank Diameter: 1/4 • Dia Metric: 6.3 • Dia Imperial: 1/4 • Cut Length Metric: 11 • Overall Length Metric: 44

Two flute straight plunging bits General-purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.

Trend Craft Pro Dovetail Cutters are designed for use with commercial dovetailing and stair housing jigs. They are also used to produce sliding and lapped dovetails, through dovetails and end on dovetails. Suitable for use on natural timbers and man-made boards.

Two flute straight plunging bits General-purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.

The Trend SET/SS31X1/4TC Router Cutter Set contains a range of popular tungsten carbide tipped cutters for a variety of applications. Suitable for softwood, hardwood, chipboard, plywood and MDF. Supplied in an aluminium carry case. Contains 9 x Non-bearing Straight Cutters 5 x 12mm, 6 x 20mm, 8 x 20mm, 10 x 20mm, 12 x 20mm, 14 x 20mm, 16 x 20mm, 18 x 20mm and 20 x 20mm 2 x Non-bearing Core Box Cutters R3.2mm and R6.35mm 2 x Non-bearing 45 V-Groove Cutters 9.5mm and 12.7mm 1 x Non-bearing Dovetail Cutter 9.5mm/13mm 1 x Non-bearing Classic Panel Cutter 12.7mm 4 x Guided Round Over Cutters R3.2mm, R6.3mm, R7.9mm and R9.5mm 4 x Guided Ovolo Cutters R3.2mm, R6.3mm, R7.9mm and R9.5mm 1 x Guided 45 …

TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. Has a TCT plunge centre tip. Specifications: • Shank Diameter: 1/2 • Dia Metric: 12.7 • Dia Imperial: 1/2 • Cut Length Metric: 25 • Overall Length Metric: 68

TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. Has a TCT plunge centre tip. Specifications: • Shank Diameter: 1/4 • Dia Metric: 12.7 • Dia Imperial: 1/2 • Cut Length Metric: 25 • Overall Length Metric: 55

TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. Specifications: • Shank Diameter: 1/4 • Dia Metric: 3 • Cut Length Metric: 11 • Overall Length Metric: 59

TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. Specifications: • Shank Diameter: 1/4 • Dia Metric: 4.7 • Dia Imperial: 3/16 • Cut Length Metric: 11 • Overall Length Metric: 51

TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. Specifications: • Shank Diameter: 1/4 • Dia Metric: 4.5 • Cut Length Metric: 11 • Overall Length Metric: 51

TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. Specifications: • Shank Diameter: 1/4 • Dia Metric: 6.3 • Dia Imperial: 1/4 • Cut Length Metric: 19 • Overall Length Metric: 61

TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. Specifications: • Shank Diameter: 1/4 • Dia Metric: 4 • Dia Imperial: 5/32 • Cut Length Metric: 11 • Overall Length Metric: 65

This versatile double-ended bit removes damaged screws, machine screws and broken bolts from wood, metal and plastic. It can remove screw sizes from Nos. 6 - 14 and broken bolts from size M4 - M8. Removes cleanly from wood, metal or plastic. Made from High Speed Steel. Removes screws made of any alloy including soft brass. Removes free spinning screws. Winslow tip for self centring. Double-ended (burnisher & tapered thread). Serrated extracting end of tool results in greater torque for hard to remove screws. Hex shoulder to aid removal of jammed screw or bolt. Set of two bits, sizes No.2 and No.3.Specifications:• Screw sizes=No.6 to No.14• Screws sizes=3.5 mm to 5 mm• Bolt sizes=M4 …