Car Jacks

Strong tubular frame supplied with a range of pins to fit the most common headstock sizes. Once in place, access to all mechanical components at the front of the bike is made easy. Stand folds down for compact storage when not in use. Supplied with width and angle adjustable rubber support pads to quickly and easily use as rear support stand. Features & Benefits: • Strong tubular frame supplied with a range of pins to fit the most common headstock sizes. • Once in place, access to all mechanical components at the front of the bike is made easy. • Stand folds down for compact storage when not in use. • Pin Sizes: 13, 15, 16.5, 17, 18mm. • Model No. FPS5 Specifications: Model No FPS5 Brand: Sea…

Designed to support and assist to accurately position engines during maintenance operations such as replacing anti-vibration mountings and certain body panels. Also used as an aid for the removal of gearboxes and transmissions. Beams supported on rubber feet and fine adjustment control is obtained by using screw/hook mechanisms. This model has the additional advantage of a 360° adjustable rotating cross beam to enable a greater range of support options when in use. Features & Benefits: • Capacity: 500kg. • Designed to support and assist to accurately position engines during maintenance operations. • Ideal for supporting the engine whilst replacing anti-vibration mountings and certain body pa…

Textured rubber provides high amount of grip while remaining soft, to prevent damage to the car underbody. Slot in the support block allows the car to be lifted by the sill. Manufactured from zinc plated steel and rubber, providing a sturdy and durable point of contact. Suitable for use with Sealey Viking 2 & 3 Tonne Jacking Beams. Used in conjunction with Model No's SJBEX.A06 or SJBEX.A07 Jacking Beam Extensions.Features & Benefits:• Textured rubber provides high amount of grip while remaining soft, to prevent damage to the car underbody.• Slot in the support block allows the car to be lifted by the sill.• Manufactured from zinc plated steel and rubber, providing a sturdy and durable point …

Use in conjunction with Model No. RE91/05 Pull Ram. The kit contains 2 x 2m chains each with one hook and two heavy-duty pull clamps. Features & Benefits: • Use in conjunction with Model No. RE91/05 Pull Ram. • The kit contains 2 x 2m chains each with one hook and two heavy-duty pull clamps. • Model No. RE91/5/CK Specifications: Model No RE91/5/CK Brand: Sealey Nett Weight: 12.60kg

Manufactured from 3.5mm steel section. Corrosion resistant finish. Ramps stack together and will stand upright for easy storage. BS Approved. Features & Benefits: • 2 Tonne Capacity per pair. • Manufactured from 3.5mm steel section. • Ramps coated with corrosion resistant finish. • Ramps stack together and will stand upright for easy storage. • Maximum Tyre Width: 200mm. • BS Approved. • Model No. CAR2000 Specifications: Model No CAR2000 Brand: Sealey Capacity Pair: 2000kg Maximum Tyre Width: 200mm Nett Weight: 14.35kg Overall Dimensions (L x W x H): 800 x 345 x 250mm Ramp Height: 190mm

Made from durable polypropylene. These ramps are designed to allow jacking access to suitable jacking points on the vehicle. Not intended to raise a vehicle enough for under vehicle servicing. Features & Benefits: • 3 Tonne Capacity per pair. • Made from durable polypropylene. • These ramps are designed to allow jacking access to suitable jacking points on the vehicle. • Not intended to raise a vehicle enough for under vehicle servicing. • Overall Dimensions (L x W x H): 700 x 200 x 80mm. • Model No. CAR3000LR Specifications: Model No CAR3000LR Brand: Sealey Capacity Pair: 3000kg Nett Weight: 0.00kg Overall Dimensions (L x W x H): 700 x 200 x 80mm Ramp Height: 65mm

Steel construction car ramp extensions to decrease ascent angle. Ideal for sports cars and vehicles with low ground clearance. Attaches to standard car ramps with a minimum width of 195mm. Suitable for use with Model No. CAR2000. Features & Benefits: • Steel construction car ramp extensions to decrease ascent angle. • Ideal for cars with low ground clearance. • Attaches to standard car ramps with a minimum width of 195mm. • Suitable for use with Model No. CAR2000. • Length: 630mm. • Capacity: 400kg Each/800kg per Pair. • Model No. CAR2001 Specifications: Model No CAR2001 Brand: Sealey Capacity Each: 400kg Capacity Pair: 800kg Length: 630mm Maximum Width: 195mm Nett Weight: 6.16kg

Manufactured from durable polypropylene. Features & Benefits: • 3 Tonne Capacity per pair. • Manufactured from durable polypropylene. • Overall Dimensions (L x W x H): 900 x 300 x 215mm. • Maximum Tyre Width: 260mm. • Model No. CAR3000C Specifications: Model No CAR3000C Brand: Sealey Capacity Pair: 3000kg Maximum Tyre Width: 260mm Nett Weight: 0.00kg Overall Dimensions (L x W x H): 900 x 300 x 215mm Ramp Height: 160mm

Compact, convenient and innovative 3 Tonne (pair) rated car ramps (maximum single axle weight of 1800kg). Supplied with four stands and removable lifting beam, designed to safely raise a vehicle completely off the ground, giving a clear workspace between vehicle and floor. Designed so the track width can be adjusted to fit various makes and model of cars with maximum tyre width of 380mm. Excellent for general servicing, exhaust work repairing damaged jacking points, sills, floor panels and undersealing. Will fit within confined areas such as garages and workshops. Safe and efficient operation, gives a clear workspace between the raised vehicle and floor. Requires a jack with a maximum saddle …

Optional Bobbin Support for Model No. RPS2 and RPS2KD. Designed to give extra support and added stability once rear axle has been located and raised. Yellow phosphate finish for added corrosion resistance. Features & Benefits: • Optional Bobbin Support for Model No. RPS2 and RPS2KD. • Designed to give extra support and added stability once rear axle has been located and raised. • Yellow phosphate finish for added corrosion resistance. • Model No. RPS1BS Specifications: Model No RPS1BS Brand: Sealey Length: 105mm Nett Weight: 0.34kg Quantity: 2

Flat arm with spring loaded roller bearings for use with SJBEX3000S and SJBEX4000S Jacking Beams. When unloaded these arms support the weight of the beam, allowing for it to run smoothly along the pit edge. In position, and when the beam is under load, the bearings retract, to leave the flat of the arm, to stabilise the lift.Features & Benefits:• Flat arm with spring loaded roller bearings for use with SJBEX3000S and SJBEX4000S Jacking Beams.• When unloaded these arms support the weight of the beam, allowing for it to run smoothly along the pit edge.• In position, and when the beam is under load, the bearings retract to leave the flat of the arm to stabilise the lift.• Model No. SJBEX.A01Speci…

Fully adjustable saddle with forward, backward and side-to-side tilt. Suitable for use with Model No's 300ETJ and 500ETJ. Features & Benefits: • A fully adjustable saddle with forward, backward and side-to-side tilt. • Suitable for use with Model No's 300ETJ and 500ETJ. • Model No. ADT7 Specifications: Model No ADT7 Brand: Sealey Capacity: 500kg Compatibility: 300ETJ, 500ETJ Nett Weight: 12.02kg

Fully adjustable saddle with forward, backward and side-to-side tilt. Suitable for Model No's. 300TR, 300TRQ, 600TR, 600TRQ. Features & Benefits: • A fully adjustable saddle with forward, backward and side-to-side tilt. • Suitable for Model No's. 300TR, 300TRQ, 600TR, 600TRQ. • Note: When using these adjustable supports the maximum capacity of the jack and support combination will be limited to the lowest specified capacity in the combination. e.g. 600TR and ADT3 - Maximum capacity is 500kg. • Model No. ADT3 Specifications: Model No ADT3 Brand: Sealey Capacity: 500kg Compatibility: 300TR, 300TRQ, 600TR, 600TRQ Nett Weight: 10.82kg

Handles and levels heavy, off-centre loads quickly and easily. Ball-bearing handle allows for a smooth and easy adjustment. Three adjustment holes accommodate different sized engines. Ideal for car, van, truck and marine engines. Suitable for use with all cranes on pages XXX and XXX. If used with cranes of capacity 680kg or more, the load must be restricted to 680kg maximum. Supplied with 4 x 275mm chains and 4 x 'L' shaped brackets with additional karabiner styled screw links. Features & Benefits: • Handles and levels heavy, off-centre loads quickly and easily. • Ball-bearing handle allows for a smooth and easy adjustment. • Three adjustment holes accommodate different sized engines. • Ide…

Triple castor wheel design allows a stabile multi-directional movement of motorcycle once lifted. Features width adjustment from 300 to 375mm, making it suitable for most types of motorcycle. Design ensures rim and tyre protection at all times. Once the bike is supported, allows easy removal and cleaning of rear wheel. For full floating movement, use in conjunction with FPS1MD. Features & Benefits: • Triple castor wheel design allows a stabile multi-directional movement of motorcycle once lifted. • Features width adjustment from 300 to 375mm, making it suitable for most types of motorcycle. • Design ensures rim and tyre protection at all times. • Once the bike is supported, allows easy removal …

Triple castor wheel design allows a stabile multi-directional movement of motorcycle once lifted. Features width adjustment from 185 to 265mm, making it suitable for most types of motorcycle. Design ensures rim and tyre protection at all times. Once the bike is supported, allows easy removal and cleaning of front wheel. Please note: All front paddock stands need to be used in conjunction with a suitable rear stand to ensure bike stability (See Model No's RPS2 or, for full floating movement, use RPS2MD). Features & Benefits: • Triple castor wheel design allows a stabile multi-directional movement of motorcycle once lifted. • Features width adjustment from 185 to 265mm, making it suitable for …

Super economy model delivered in knock-down form for reduced freight cost. Fast folding model provides easy storage and transportation with heavy-duty castors. Weighs only 75kg and is perfect for mobile or workshop use. Side pump access with removable handle. Features & Benefits: • Lifts 1000kg at 830mm jib extension. • Fast folding design. • Heavy-duty castors. • Weighs only 75kg. • Side pump access with removable handle. • Delivered in knock-down form. • Some self-assembly required. • This item is heavy. Extra assistance must be provided at the delivery point to help its safe delivery. • Model No. SC10 Specifications: Model No SC10 Brand: Sealey Height Jib Down: 1390mm Height Legs Folded…

Designed to prevent damage to the underside of the vehicle's jacking point. Design Type C. Profile Depth 23.8mm. Size 108mm. Fits saddle 106-108mm.

Designed to prevent damage to the underside of the vehicle's jacking point. Design Type B. Profile Depth 7.5mm. Size 104mm. Fits saddle 93-95mm.

Designed to prevent damage to the underside of the vehicle's jacking point. Design Type A. Profile Depth 19mm. Size 137.5mm. Fits saddle 116-123mm.

Pair of chocks to prevent vehicles moving whilst working with trolley jacks, scissor jacks, bottle jacks, axle stands or on a slope. Display carton.

Two rubber wheel chocks. Prevents vehicle movement when being jacked on a level surface or parked on an incline not exceeding 12°. Suitable for vehicles below 5 tonne. Features & Benefits: • Two rubber wheel chocks. • Prevents vehicle movement when being jacked on a level surface or parked on an incline not exceeding 12°. • Suitable for vehicles below 5 tonne. • Model No. WC02

Two rubber wheel chocks. Prevents vehicle movement when being jacked on a level surface or parked on an incline not exceeding 12°. Suitable for vehicles below 3 tonne. Features & Benefits: • Two rubber wheel chocks. • Prevents vehicle movement when being jacked on a level surface or parked on an incline not exceeding 12°. • Suitable for vehicles below 3 tonne. • Model No. WC01

Single nylon reinforced rubber wheel chock. Prevents vehicle movement when being jacked on a level surface or parked on an incline not exceeding 12°. Fitted with eye bolt for rope or chain. Suitable for vehicles below 10 Tonne. Features & Benefits: • Single nylon reinforced rubber wheel chock. • Prevents vehicle movement when being jacked on a level surface or parked on an incline not exceeding 12°. • Fitted with eye bolt for rope or chain. • Suitable for vehicles below 10 Tonne. • Model No. WC03