Power Tool Accessories Dremel

Use for shaping. smoothing and material removal. Use on hardened steel. stainless steel. cast iron. nonferrous metals. fired ceramics. plastics. hardwoods and other hard materials. Shank diameter: 3.2 mm Working diameter: 3.2 mm Accessory length: 38.0 mm Max 30.000 rpm

Use for shaping, smoothing and material removal. Use on hardened steel, stainless steel, cast iron, nonferrous metals, fired ceramics, plastics, hardwoods and other hard materials. Technical Specifications: Shank diameter 3.2mm. Working diameter: 3.2mm Accessory length: 39mm. Maximum Speed: 30,000rpm. Recommended attachment: Detailer's Grip Attachment Ref. 577

9910 Spear Tip Shank diameter: 3.2 mm Working diameter: 3.2 mm Accessory length: 39 mm Width: 3 mm Length: 3 mm Height: 39 mm Maximum RPM: 30,000 1/min 9911 Egg Tip Shank diameter: 3.2 mm Working diameter: 3.2 mm Accessory length: 39 mm Width: 3 mm Length: 30 mm Height: 39 mm Maximum RPM: 30,000 1/min 9931 Spear Tip Shank diameter: 3.2 mm Working diameter: 6.4 mm Accessory length: 45 mm Width: 4 mm Length: 4 mm Height: 45 mm Maximum RPM: 35,000 1/min

9910 Spear Tip Shank diameter: 3.2 mm Working diameter: 3.2 mm Accessory length: 39 mm Width: 3 mm Length: 3 mm Height: 39 mm Maximum RPM: 30,000 1/min 9911 Egg Tip Shank diameter: 3.2 mm Working diameter: 3.2 mm Accessory length: 39 mm Width: 3 mm Length: 30 mm Height: 39 mm Maximum RPM: 30,000 1/min 9931 Spear Tip Shank diameter: 3.2 mm Working diameter: 6.4 mm Accessory length: 45 mm Width: 4 mm Length: 4 mm Height: 45 mm Maximum RPM: 35,000 1/min

Saw blade for longer cut offs, which are normally limited by the throat depth of the tool. In terms of technical specifications, this blade is identical to the MS51 General Purpose blade, however, its top and bottom parts are 90 degrees twisted. This twist allows a lateral material feed either from left or right, resulting in technically infinite cuts. Technical specifications: Length: 100mm Cutting depth: 12mm. Teeth per centimeter: 6 Blade width: 0.4mm. Blade depth:2.5mm.

Piloted Beading Bit. A decorative bit for detailed edges. Suitable for use on Veneered woods, fibreboard, chipboard, plywood, softwood, hardwood, rubber, plastic, plexiglass and carbon Technical Specifications Shank diameter: 3.2mm. Working diameter: 9.5mm. Working length: 4.8mm Accessory length: 37mm Usage: Piloted beading. Maximum speed: 35,000rpm. Essential attachment: Shaper /Router table Ref.231

A flexible heat resistant mat that can be used to catch excessive glue and to create decorative glue design patterns: allow glue to cool and peel it off easily. The pad is suitable for all types of melted glue. Size: 20cm x 20cm.

For fine detail work, cutting, engraving, carving, touch-up and finishing. Use on wood, jade, ceramic, glass, hardened steel, semi-precious stones and other hard materials. Bits are covered with diamond particles. 7105 Diamond Wheel Point 4.4 mm Shank diameter: 3.2 mm Working diameter: 4.4 mm Accessory length: 46 mm Width: 4 mm Length: 4 mm Height: 46 mm Maximum RPM: 25,000 1/min 7122 Diamond Wheel Point 2.4mm Shank diameter: 3.2 mm Working diameter: 2.4 mm Accessory length: 46 mm Width: 3 mm Length: 3 mm Height: 46 mm Maximum RPM: 25,000 1/min

Piloted Corner Rounding Bit. Rounding over edges and corners. Suitable for use on Veneered woods, fibreboard, chipboard, plywood, softwood, hardwood, rubber, plastic, plexiglass and carbon Technical Specifications Shank diameter: 3.2mm. Working diameter: 9.5mm. Working length: 4.8mm Accessory length: 37mm Usage: Corner Rounding. Maximum speed: 35,000rpm. Essential attachment: Shaper /Router table Ref.231

Diamond Engraving Point. For usage with the Dremel Engraver 290. The Diamond Engraving Point 9929 has a longer lifespan and is for use on harder materials such as glass.

Piloted Corner Rounding Bit. Rounding over edges and corners. Suitable for use on Veneered woods, fibreboard, chipboard, plywood, softwood, hardwood, rubber, plastic, plexiglass and carbon Technical Specifications Shank diameter: 3.2mm. Working diameter: 8.0mm. Working length: 2.7mm Accessory length: 37mm Usage: Keyhole . Maximum speed: 35,000rpm. Essential attachment: Shaper /Router table Ref.231

Milling Accessory

Fast cutting sharp teeth for greater material removal. Use on fiberglass,wood, plastic, epoxy, rubber, laminates, particle board, soft metals, leather, ceramic tile. Shank Diameter: 3.2mm. working Diameter: 7.8mm. Accessory length: 40mm. Maximum speed: 35,000rpm.

Fast cutting sharp teeth for greater material removal. Use on fiberglass,wood, plastic, epoxy, rubber, laminates, particle board, soft metals, ceramic tile. Shank diameter: 3.2mm. Working Diameter; 19mm. Accessory length: 45mm. Maximum speed: 35,000rpm.

Milling Accessory

Work in small spaces with 12 senses to choose from and the normal functions of your Dremel multi-tool.The attachment´s 90° set head offers excellent visibility to the surface while maintaining control of the multi-tool.Just bolt it onto your Dremel multitool to work faster.Its durable, lightweight design offers a multi-tool-like feel while allowing you to work in hard-to-reach spaces.Contents:1 angle head, 1 impeller cover and 1 manual/quick start guide.Length:8.5:cm.Width:3:in.Depth:6:in.SOL Date:01.10.2020:Retired:no:Reasons to buy (online dealer):Work in small spaces with 12 senses to choose from and the normal functions of your Dremel multitool:Product box length:9:cm.Product box height:12:cm.Pr…