Bits & Sockets Sets

A single fluted high steel cutter for pierce and trimming of aluminium faced panels in the caravan industry. Specifications: • Shank Diameter: 1/4 • Dia Metric: 6.3 • Dia Imperial: 1/4 more→• Cut Length Metric: 19.1 • Overall Length Metric: 76

Cuts groove for Trend Routaseal. Position seal into apex of jamb and stop. More economic to use than more complex seals. Use with a small 1/4 inch shank hand router. Use STC for abrasive material. more→Specifications: • Shank Diameter: 1/4 • Dia Metric: 5 • Cut Length Metric: 3 • Overall Length Metric: 61 • Angle: 115

Eccentric single flute cutters. Cutters are chosen for fast free cutting, when cutting speed takes preference over finish. Small diameter tools must be handled with care to avoid breakage. Singl more→e flute cutters should not be used in eccentric chucks. Specifications: • Shank Diameter: 1/4 • Dia Metric: 5 • Cut Length Metric: 19 • Overall Length Metric: 51

This fine height adjuster simply fits onto the router and allows fine adjustment of the cutter height. They are especially useful for accurate work such as when the router is held inverted in a rout more→er table. Suitable for the following TREND T10, T12 ELU MOF 177(E), 131 DEWALT DW624, 625EK, 629, DWE625 CMT CMT1E 2E

Cutter for use with the Leigh Dovetail Jig. These cutters have extra long shanks. Specifications: • Shank Diameter: 1/2 • Dia Metric: 20.5 • Cut Length Metric: 32 • Overall Len more→gth Metric: 83 • Angle: 98

Template thickness should be at least 5mm thicker than cutter cut length of cutter. Approximately 1.0mm flat will be found on the nose. Specifications: • Shank Diameter: 1/4 • Dia Metric: more→12.7 • Dia Imperial: 1/2 • Cut Length Metric: 12.7 • Cut Length Imperial: 1/2 • Overall Length Metric: 63.31 • Bearing Dia Metric: 12.7 • Bearing Dia Imperial: 1/2 • Angle: 45

TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. Has a TCT plunge centre tip. Specifications: • Shank Dia more→meter: 1/2 • Dia Metric: 16 • Dia Imperial: 5/8 • Cut Length Metric: 19 • Overall Length Metric: 60

Template thickness should be 5mm thicker than cut length of cutter. Specifications: • Shank Diameter: 1/4 • Dia Metric: 12.7 • Dia Imperial: 1/2 • Cut Length Metric: 9.5 • Cu more→t Length Imperial: 3/8 • Overall Length Metric: 50 • Bearing Dia Metric: 12.7 • Bearing Dia Imperial: 1/2 • Radius 1 Metric: 6.35

For coves and part of a rule joint. Specifications: • Shank Diameter: 1/4 • Dia Metric: 8 • Cut Length Metric: 12.7 • Cut Length Imperial: 1/2 • Overall Length Metric: 56.7 & more→bull; Radius 1 Metric: 4

A two flute cutters with extra long shanks. Deep grooving, rebating and mortising. Useful for template work when thickness of template restricts depth. Extra care must be taken to avoid breakage more→. Specifications: • Shank Diameter: 1/2 • Dia Metric: 12.7 • Dia Imperial: 1/2 • Cut Length Metric: 22 • Overall Length Metric: 95 • Type or Grade: Two flute

Expert Quality, 6 point sockets forged from chrome molybdenum hardened, tempered and chemically blacked for corrosion protection. Supplied with pin and ring. These sockets are for use with air, electr more→ic or manual impact wrenches. Contents: 1 x Expert HI-TORQ® 6 Point Deep Impact Socket, 1" Sq. Dr., 65mm