Bits & Sockets Sets

Self-guiding cutters with the facility to change the profile by fitting a larger bearing & varying the depth. Supplied with two bearings. The larger bearing removes the bottom quirk. Specificatio more→ns: • Shank Diameter: 1/2 • Dia Metric: 29 • Cut Length Metric: 12.7 • Cut Length Imperial: 1/2 • Overall Length Metric: 60 • Bearing Dia Metric: 9.5 • Bearing Dia Imperial: 3/8 • Radius 1 Metric: 4

A self-guided combination trimmer. A 90 degree trim is obtained by engaging the bottom half. A 45 degree trim is obtained by lowering the cutter. A fine height adjuster is recommended when using more→this cutter. A larger 20mm bearing will spread the wear of the cutting when 45 degree trimming. Specifications: • Shank Diameter: 1/4 • Dia Metric: 24 • Cut Length Metric: 6 • Overall Length Metric: 55 • Angle: 90

The glazing bar ovolo cutter is bearing guided to speed setting-up and to enable curved frames to be moulded. Specifications: • Shank Diameter: 1/2 • Dia Metric: 27 • Cut Length Metri more→c: 17 • Overall Length Metric: 65 • Bearing Dia Metric: 9.5 • Radius 1 Metric: 17

The glazing bar ovolo cutter is bearing guided to speed setting-up and to enable curved frames to be moulded. Specifications: • Shank Diameter: 1/4 • Dia Metric: 27 • Cut Length Metric more→: 17 • Overall Length Metric: 66.5 • Bearing Dia Metric: 9.5 • Type or Grade: Profile • Radius 1 Metric: 17

For door and window construction, decorative panelling and many other joinery applications. Specifications: • Shank Diameter: 1/4 • Dia Metric: 33.5 • Cut Length Metric: 9 • Overa more→ll Length Metric: 64 • Bearing Dia Metric: 9.5 • Type or Grade: Profile • Radius 1 Metric: 9

Shank mounted bearing profilers are ideal for template guidance. Use for rebating and trimming edges only. Extra care must be taken to avoid cutter breakage. Specifications: • Shank Diameter more→: 1/2 • Dia Metric: 18.2 • Dia Imperial: 23/32 • Cut Length Metric: 50 • Cut Length Imperial: 2 • Overall Length Metric: 103 • Bearing Dia Metric: 18.2 • Bearing Dia Imperial: 23/32 • Angle: 90

Panel raiser cutters for producing the panel for cabinet panelled doors, tool matches our range of profile scribers. Suitable for use on natural timber and MDF. For use in a router table only. Take more→several passes, increasing the depth with each pass. Must be used in a stationary variable speed router either mounted overhead or inverted in a router table at a reduced speed. For use on natural timber and MDF. Stationary use only. Can be used for curved panels if a copy pin is used. Specifications: • Shank Diameter: 8 mm • Dia Metric: 45 • Dia2 Metric: 11 • Cut Length Metric: 17 • Overall Length Metric: 49.5 • Angle: 10

For door and window construction, decorative panelling and many other joinery applications. Designed for 44mm timber thicknesses. Specifications: • Shank Diameter: 1/4 • Dia Metric: 31 &b more→ull; Cut Length Metric: 13 • Overall Length Metric: 56 • Bearing Dia Metric: 12.7 • Type or Grade: Scribe • Radius 1 Metric: 17

Ideal for speaker cabinets and drawer construction. Please note. This tool cannot be re-sharpened. Inverted use only. Use on MDF and natural timbers. Specifications: • Shank Diameter: 1/4 more→• Dia Metric: 42 • Cut Length Metric: 14.3 • Overall Length Metric: 54.5 • Type or Grade: 8 to 12mm • Angle: 45

For door and window construction, decorative panelling and many other joinery applications. Designed for 35mm and 44mm timber thicknesses. Specifications: • Shank Diameter: 1/4 • Dia Metr more→ic: 36.7 • Cut Length Metric: 9 • Overall Length Metric: 52 • Bearing Dia Metric: 12.7 • Type or Grade: Scribe • Radius 1 Metric: 9

Ideally suited for cutting radiused edges at speed, as a side fence can be dispensed with. The guide bearing follows the vertical edge or template. Alternative bearing Ref. B127A creates a shallow ra more→dius. Specifications: • Shank Diameter: 1/2 • Dia Metric: 41.3 • Dia Imperial: 1 5/8 • Cut Length Metric: 19.1 • Cut Length Imperial: 3/4 • Overall Length Metric: 66.5 • Bearing Dia Metric: 9.5 • Radius 1 Metric: 16

Designed for sash bar window construction. Specifications: • Shank Diameter: 1/4 • Dia Metric: 22 • Cut Length Metric: 18 • Overall Length Metric: 58 • Radius 1 Metric: 10

Enables curved frames to be moulded. Specifications: • Shank Diameter: 1/2 • Dia Metric: 28.5 • Cut Length Metric: 20 • Overall Length Metric: 58.5 • Radius 1 Metric: 17

A 'T' slot cutters for clamping and hanging applications. Relief cut required. MEC mechanical feed only. Specifications: • Shank Diameter: 1/2 • Dia Metric: 30 • Dia2 Metric: 10.5 &b more→ull; Cut Length Metric: 7 • Overall Length Metric: 55.5 • Radius 1 Metric: 3

Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Cutter has a bottom cut feature. Sp more→ecifications: • Shank Diameter: 1/2 • Dia Metric: 41.3 • Dia Imperial: 1 5/8 • Cut Length Metric: 25 • Cut Length Imperial: 1 • Overall Length Metric: 66

Produces an elegant edge mould, or a shallow panel effect when routing on its full width. Specifications: • Shank Diameter: 1/2 • Dia Metric: 20 • Cut Length Metric: 15 • Overall more→Length Metric: 53 • Radius 1 Metric: 6

TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. Has a TCT plunge centre tip. Specifications: • Shank Dia more→meter: 1/2 • Dia Metric: 15.9 • Dia Imperial: 5/8 • Cut Length Metric: 50 • Overall Length Metric: 96

With bearing guided ogees, change profile by using a larger bearing and vary the depth. Specifications: • Shank Diameter: 1/2 • Dia Metric: 25.4 • Dia Imperial: 1 • Cut Length Met more→ric: 15.9 • Cut Length Imperial: 5/8 • Overall Length Metric: 63 • Bearing Dia Metric: 9.5 • Bearing Dia Imperial: 3/8 • Radius 1 Metric: 4

With bearing guided ogees, change profile by using a larger bearing and vary the depth. Specifications: • Shank Diameter: 1/4 • Dia Metric: 25.4 • Dia Imperial: 1 • Cut Length Met more→ric: 15.9 • Cut Length Imperial: 5/8 • Overall Length Metric: 54 • Bearing Dia Metric: 9.5 • Bearing Dia Imperial: 3/8 • Radius 1 Metric: 4

These machine bits are typically used by kitchen furniture manufacturers for recessing circular hinges. This type without scribers are for laminate covered boards. Specifications: • Shank Diamet more→er: 1/4 • Dia Metric: 35 • Dia Imperial: 1 3/8 • Overall Length Metric: 65 • Type or Grade: TCT

A range of heavy duty 'T' slot cutters for clamping and hanging applications. MEC mechanical feed only. Specifications: • Shank Diameter: 3/8 • Dia Metric: 28 • Dia2 Metric: 11.2 &bul more→l; Cut Length Metric: 4 • Overall Length Metric: 52 • Radius 1 Metric: 2

A range of heavy duty 'T' slot cutters for clamping and hanging applications. Relief cut required. Specifications: • Shank Diameter: 3/8 • Dia Metric: 28 • Dia2 Metric: 9.5 • Cut more→Length Metric: 8 • Overall Length Metric: 60