Bits & Sockets Sets

Two blades. Replaceable tips increase productivity. Low profile bearing fixing screw. Specifications: • Shank Diameter: 1/4 • Dia Metric: 26 • Cut Length Metric: 15.7 • Overall Length Metric: 52.5

These machine bits are typically used by kitchen furniture manufacturers for recessing circular hinges. This type without scribers are for laminate covered boards. Specifications: • Shank Diameter: 3/8 • Dia Metric: 35 • Dia Imperial: 1 3/8 • Overall Length Metric: 65 • Type or Grade: TCT

Enables biscuit jointing with timber, man-made fibre and particle board. The correct choice of bearing will ensure the correct depth of cut for biscuit sizes No.0, 10 & 20. Specifications: • Shank Diameter: 1/2 • Dia Metric: 37.2 • Dia Imperial: 29/64 • Cut Length Metric: 4 • Overall Length Metric: 64 • Bearing Dia Metric: 12.7

Enables biscuit jointing with timber, man-made fibre and particle board. The correct choice of bearing will ensure the correct depth of cut for biscuit sizes No.0, 10 & 20. Specifications: • Shank Diameter: 1/4 • Dia Metric: 37.2 • Dia Imperial: 29/64 • Cut Length Metric: 4 • Overall Length Metric: 64 • Bearing Dia Metric: 12.7

Self-guiding cutters with the facility to change the profile by fitting a larger bearing & varying the depth. Supplied with two bearings. The larger bearing removes the bottom quirk. Specifications: • Shank Diameter: 1/2 • Dia Metric: 29 • Cut Length Metric: 12.7 • Cut Length Imperial: 1/2 • Overall Length Metric: 60 • Bearing Dia Metric: 9.5 • Bearing Dia Imperial: 3/8 • Radius 1 Metric: 4

A self-guided combination trimmer. A 90 degree trim is obtained by engaging the bottom half. A 45 degree trim is obtained by lowering the cutter. A fine height adjuster is recommended when using this cutter. A larger 20mm bearing will spread the wear of the cutting when 45 degree trimming. Specifications: • Shank Diameter: 1/4 • Dia Metric: 24 • Cut Length Metric: 6 • Overall Length Metric: 55 • Angle: 90

The glazing bar ovolo cutter is bearing guided to speed setting-up and to enable curved frames to be moulded. Specifications: • Shank Diameter: 1/2 • Dia Metric: 27 • Cut Length Metric: 17 • Overall Length Metric: 65 • Bearing Dia Metric: 9.5 • Radius 1 Metric: 17

The glazing bar ovolo cutter is bearing guided to speed setting-up and to enable curved frames to be moulded. Specifications: • Shank Diameter: 1/4 • Dia Metric: 27 • Cut Length Metric: 17 • Overall Length Metric: 66.5 • Bearing Dia Metric: 9.5 • Type or Grade: Profile • Radius 1 Metric: 17

For door and window construction, decorative panelling and many other joinery applications. Specifications: • Shank Diameter: 1/4 • Dia Metric: 33.5 • Cut Length Metric: 9 • Overall Length Metric: 64 • Bearing Dia Metric: 9.5 • Type or Grade: Profile • Radius 1 Metric: 9

Shank mounted bearing profilers are ideal for template guidance. Use for rebating and trimming edges only. Extra care must be taken to avoid cutter breakage. Specifications: • Shank Diameter: 1/2 • Dia Metric: 18.2 • Dia Imperial: 23/32 • Cut Length Metric: 50 • Cut Length Imperial: 2 • Overall Length Metric: 103 • Bearing Dia Metric: 18.2 • Bearing Dia Imperial: 23/32 • Angle: 90

Panel raiser cutters for producing the panel for cabinet panelled doors, tool matches our range of profile scribers. Suitable for use on natural timber and MDF. For use in a router table only. Take several passes, increasing the depth with each pass. Must be used in a stationary variable speed router either mounted overhead or inverted in a router table at a reduced speed. For use on natural timber and MDF. Stationary use only. Can be used for curved panels if a copy pin is used. Specifications: • Shank Diameter: 8 mm • Dia Metric: 45 • Dia2 Metric: 11 • Cut Length Metric: 17 • Overall Length Metric: 49.5 • Angle: 10

For door and window construction, decorative panelling and many other joinery applications. Designed for 44mm timber thicknesses. Specifications: • Shank Diameter: 1/4 • Dia Metric: 31 • Cut Length Metric: 13 • Overall Length Metric: 56 • Bearing Dia Metric: 12.7 • Type or Grade: Scribe • Radius 1 Metric: 17

Ideal for speaker cabinets and drawer construction. Please note. This tool cannot be re-sharpened. Inverted use only. Use on MDF and natural timbers. Specifications: • Shank Diameter: 1/4 • Dia Metric: 42 • Cut Length Metric: 14.3 • Overall Length Metric: 54.5 • Type or Grade: 8 to 12mm • Angle: 45

For door and window construction, decorative panelling and many other joinery applications. Designed for 35mm and 44mm timber thicknesses. Specifications: • Shank Diameter: 1/4 • Dia Metric: 36.7 • Cut Length Metric: 9 • Overall Length Metric: 52 • Bearing Dia Metric: 12.7 • Type or Grade: Scribe • Radius 1 Metric: 9

Ideally suited for cutting radiused edges at speed, as a side fence can be dispensed with. The guide bearing follows the vertical edge or template. Alternative bearing Ref. B127A creates a shallow radius. Specifications: • Shank Diameter: 1/2 • Dia Metric: 41.3 • Dia Imperial: 1 5/8 • Cut Length Metric: 19.1 • Cut Length Imperial: 3/4 • Overall Length Metric: 66.5 • Bearing Dia Metric: 9.5 • Radius 1 Metric: 16

Designed for sash bar window construction. Specifications: • Shank Diameter: 1/4 • Dia Metric: 22 • Cut Length Metric: 18 • Overall Length Metric: 58 • Radius 1 Metric: 10

Enables curved frames to be moulded. Specifications: • Shank Diameter: 1/2 • Dia Metric: 28.5 • Cut Length Metric: 20 • Overall Length Metric: 58.5 • Radius 1 Metric: 17

A 'T' slot cutters for clamping and hanging applications. Relief cut required. MEC mechanical feed only. Specifications: • Shank Diameter: 1/2 • Dia Metric: 30 • Dia2 Metric: 10.5 • Cut Length Metric: 7 • Overall Length Metric: 55.5 • Radius 1 Metric: 3

Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Cutter has a bottom cut feature. Specifications: • Shank Diameter: 1/2 • Dia Metric: 41.3 • Dia Imperial: 1 5/8 • Cut Length Metric: 25 • Cut Length Imperial: 1 • Overall Length Metric: 66

Produces an elegant edge mould, or a shallow panel effect when routing on its full width. Specifications: • Shank Diameter: 1/2 • Dia Metric: 20 • Cut Length Metric: 15 • Overall Length Metric: 53 • Radius 1 Metric: 6

Two flute straight cutters produce a cleaner finish than the single flute cutters. Suitable for grooving, rebating, mortising and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood, certain hardwoods and hard plastic. Two flutes give a clean finish to cut edges. All cutters above and including 9.5mm diameter, have TCT plunge centre tips.

With bearing guided ogees, change profile by using a larger bearing and vary the depth. Specifications: • Shank Diameter: 1/2 • Dia Metric: 25.4 • Dia Imperial: 1 • Cut Length Metric: 15.9 • Cut Length Imperial: 5/8 • Overall Length Metric: 63 • Bearing Dia Metric: 9.5 • Bearing Dia Imperial: 3/8 • Radius 1 Metric: 4

With bearing guided ogees, change profile by using a larger bearing and vary the depth. Specifications: • Shank Diameter: 1/4 • Dia Metric: 25.4 • Dia Imperial: 1 • Cut Length Metric: 15.9 • Cut Length Imperial: 5/8 • Overall Length Metric: 54 • Bearing Dia Metric: 9.5 • Bearing Dia Imperial: 3/8 • Radius 1 Metric: 4

These machine bits are typically used by kitchen furniture manufacturers for recessing circular hinges. This type without scribers are for laminate covered boards. Specifications: • Shank Diameter: 1/4 • Dia Metric: 35 • Dia Imperial: 1 3/8 • Overall Length Metric: 65 • Type or Grade: TCT