Bits & Sockets Sets

A large rigid router table insert plate for incorporation into user-made router tables. Thermoset phenolic. Two concentric snap-in rings. Three hole sizes of 98mm, 68mm & 32mm dia. Concentric rings and radial lines on underside for easy centring of router. Moulded with slight crown (0.8mm) for distortion free cuts. Corner clips to clamp to table underside. Can be mounted to 19mm tops with edge rebate of 6.35mm deep x 12.7mm wide. Plate will require drilling by user to suit make and model of router to be fitted. User made router table will require safety device accessories to be fitted. Contents: 2 x Concentric Rings 1 x Lead-on Pin

A template to rout holes in various diameters and to put a concave or convex shape on the component. A template profiler cutter can be used to create holes of 25mm, 50mm, 75mm and 100mm in diameter. The template edge also includes a concave or convex 50mm and 100mm radius profile. A variety of other size holes & curves can be achieved by using a different combination of cutter and guide bush. A Unibase may be required for certain makes and model of router.

A template to allow routing or drilling of 32mm centre holes for 5mm diameter shelf supports. The template is a clear plastic with an adjustable clamping bar with two locking knobs. Supplied with twelve 5mm metal shelf supports, one alloy knurled index pin and a 9.5mm diameter guide bush. Allows holes to be positioned from 10mm to 64mm from edge of board. This template can be used to add existing holes to a unit, or for user made shelves, the index lines to allow for easy setting up. Template can also be used with a power drill and an accessory quick release 5mm shelf support drill bit guide Ref. SNAP/SS/5MM or TEMP/SSD/5MM . This bit has a lip and spur drill fitted for drilling blind holes.…

A unique concept which allows oval pockets to be routed, to disguise ugly resin pockets and knots in timber. This is especially required when softwoods are being used. Can be udes to repair blown worktop joints when care is used to ensure the plug is glued in perfectly level. See Knowledge for deatils. The template is supplied with a 10mm diameter 1/4 inch shank cutter, a 20mm template guide bush and a 40mm inlay collar. Unibase may be required for certain makes & models of router.

For 4.0mm thick strip. For 20.0mm wide intumescent strip. Specifications: • Shank Diameter: 1/2 • Dia Metric: 40 • Cut Length Metric: 20 • Overall Length Metric: 73 • Bearing Dia Metric: 32 • Rebate Metric: 4

• One of a comprehensive range of Premier Hand Tools, suitable for daily professional use.• Manufactured from hardened and tempered Chrome Vanadium steel with a micro satin finish.• Low profile 6-point WallDrive® sockets.• Low profile 90-tooth pear-head ratchet with super slim handle.• Features flip reverse and quick release mechanism.• Ideal for use under dashboards and on auxiliary belts as well as any other applications where access is restricted.• Contents: Sockets; 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 21, 22, 24mm, 150mm Extension Bar, 90-Tooth Pear-head ratchet with flip reverse and quick release mechanism.• Supplied in an EVA storage tray.• Lifetime guarantee*.Manufactured from hardened and t…

Easy wipe clean material and comfortable feel
Drive: Hexagon, Solid 6.3mm (1/4") Output: Slot Profile (Negative), Cross-Recessed Profile (Plus) PH, Posi-Drive Profile PZ, Inner Hex Profile, Inner TORX Profile, Tamper Proof TORX Profile. Wrench Size: ♍ 1,5-6 Ý 0,5 x 4-1,2 x 6,5 Ý PH1-PH3 PZ1 - PZ3 T6-T40 Dimensions/Length: 130mm x 118mm x 50mm
[Set Contents] 1 x HAZET Smart Case Bit Set 2200SC-1|69 Pieces, Manual Operation, Drill and Cordless Driver Adapter, Various Bits in Compact Case | Length: 5.1 x 4.6 x 2.0 inches (130 x 118 x 50 mm)

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the Expert SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals drilling concrete an…

The HSS Twist Drill Bit Titanium offers maximum lifetime while drilling holes in metal. When using the appropriate cooling system, the drill bit has the lowest possible level of friction and minimal wear, due to its titanium-nitride coating. The high surface quality of this ground twist drill bit, which is made from HSS (high-speed steel), allows for extended usage. It is suitable for use on alloyed and non-alloyed steel, malleable cast iron, sintered iron, new silver, copper, bronze and hard plastics such as perspex. The HSS Twist Drill Bit Titanium is manufactured to DIN 338. The drill bit is Type N (flute angle) with a 135-degree tip and a diameter tolerance of h8. Active cutting and perfect …

DS max-7:30 x 400 x 520.Bosch Accessories.Product net weight (kg):1,248.Electric tool accessories.

• Specialised socket designed to remove the ABS rotor ring prior to wheel bearing replacement.• Specifically engineered to cope with the high torque settings required to remove/refit the rotor ring.• Suitable for XJ8 (97-03), XK8 (96on)Specialised socket designed to remove the ABS rotor ring prior to wheel bearing replacement. Specifically engineered to cope with the high torque settings required to remove/refit the rotor ring. Suitable for XJ8 (97-03), XK8 (96on).• Specialised socket designed to remove the ABS rotor ring prior to wheel bearing replacement. • Specifically engineered to cope with the high torque settings required to remove/refit the rotor ring. • Suitable for XJ8 (97-03), XK8…

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job and it has traditionally taken its toll on hammer drill bits. Even 4-cutters wear out fast, resulting in downtime changing accessories and fetching supplies. The Full Carbide Head on the Expert SDS max-8x is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS max-8x lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals dr…