Bits & Sockets Sets

Profiler with shank mounted bearing guides. For use with router mounted above or below a table when following a template. For profiling and rebating applications only. Not for plunge cutting/groo more→ving. A 3mm maximum overlap should be left before trimming. They are ideal for template making. Specifications: • Shank Diameter: 1/2 • Dia Metric: 25 • Cut Length Metric: 25 • Overall Length Metric: 73 • Bearing Dia Metric: 25

Ideal for newel posts and caps for stairs. Supplied with one bearing. Specifications: • Shank Diameter: 1/4 • Dia Metric: 31.8 • Dia Imperial: 1 1/4 • Cut Length Metric: 12 &bul more→l; Overall Length Metric: 64 • Bearing Dia Metric: 9.5 • Bearing Dia Imperial: 3/8 • Angle: 45

Ideal for newel posts and caps for stairs. Supplied with one bearing. Specifications: • Shank Diameter: 1/2 • Dia Metric: 31.8 • Dia Imperial: 1 1/4 • Cut Length Metric: 12 &bul more→l; Overall Length Metric: 60 • Bearing Dia Metric: 9.5 • Bearing Dia Imperial: 3/8 • Angle: 45

Trend Craft Pro 1/2in shank Aquamac cutter - 46.3mm diameter Two Flute Carbide tips. Speeds up the fitting of specialist weather seals Schlegel Aquamac 21 or Exitex Aquatex A10 seal. Cuts the correc more→t sized groove and recess in a single pass for increased productivity Flat bottom cut for sitting on the floor of a rebate for perfect positioning. PTFE coating to minimise heat and resin build up for increased cutter performance and longevity. 1/2in shank for use in bigger routers and heavier applications with 'K'mark shank to ensure safe working practices. Specifications: • Shank Diameter: 1/2 • Dia Metric: 46.3 • Dia2 Metric: 34.3 • Cut Length Metric: 2.7/10.3 • …

Recessing cutter will accommodate the Schlegel Aquamac 63 or Exitex Aquatex P6 weather strip system and allows for a particularly small gap between sash and frame. The slot can be positioned part way more→down the side of the rebate, or at the bottom of the rebate. Specifications: • Shank Diameter: 1/2 • Dia Metric: 41.3 • Dia Imperial: 1 5/8 • Dia2 Metric: 28.3 • Cut Length Metric: 2.7/4.8 • Overall Length Metric: 67 • Bearing Dia Metric: 22

A reversible finger jointer, to increase the gluing area for edge to edge joints. Specifications: • Shank Diameter: 1/2 • Dia Metric: 40 • Dia2 Metric: 31 • Cut Length Metric: 32 more→• Overall Length Metric: 70

Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Cutter has a bottom cut feature. Sp more→ecifications: • Shank Diameter: 1/2 • Dia Metric: 50 • Dia Imperial: 1 31/32 • Cut Length Metric: 25 • Cut Length Imperial: 1 • Overall Length Metric: 64

Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Cutter has a bottom cut feature. Sp more→ecifications: • Shank Diameter: 1/2 • Dia Metric: 50.8 • Dia Imperial: 2 • Cut Length Metric: 25 • Cut Length Imperial: 1 • Overall Length Metric: 66

Use for producing mortar grooves and for bevelling applications. Specifications: • Shank Diameter: 1/2 • Dia Metric: 38 • Cut Length Metric: 27 • Overall Length Metric: 62.5 &bull more→; Angle: 60

TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. Has a TCT plunge centre tip. Specifications: • Shank Dia more→meter: 1/2 • Dia Metric: 27 • Dia Imperial: 1 1/16 • Cut Length Metric: 32 • Overall Length Metric: 72

These slotters have a 12mm clear bore to enable them to be mounted at any position on the arbor in combination with spacers, with or without a bearing. Specifications: • Dia Metric: 50 • S more→awbore: 12 • Saw Kerf Metric: 4 • Saw Teeth: 4

Ideal for producing nosings and attractive edge moulds. Specifications: • Shank Diameter: 1/4 • Dia Metric: 25 • Cut Length Metric: 12 • Overall Length Metric: 57.5 • Radius more→1 Metric: 6

Gives a narrow appearance to a board edge. Specifications: • Shank Diameter: 1/4 • Dia Metric: 22 • Cut Length Metric: 10 • Overall Length Metric: 39 • Radius 1 Metric: 3

T-handle screwdriver: The ideal handle shape to allow high torque transmission in difficult tightening and loosening situations. The ergonomic shape of the handle fills the palm of the hand well, the more→fingers lie safely in the soft rounded handle recesses. The whole hand makes contact with the handle and friction losses between the hand and the handle are avoided. Special surface treatment of the blades for high corrosion protection and an optimum fit in the screw head.Features and Benefits:• T-handle screwdriver for the transmission of particularly high tightening and loosening torque• Ergonomic 2-component handle with finger handle recesses and pleasant surface feel for very high …

The Step Drill Bit Is Made Of Hss (High-Speed Steel) And Offers A Long Lifetime When Using Coolant. Easily Visible And Durable Markings Of The Hole Diameter Are Provided By Laser-Marked Figures In Bot more→h Spiral Flutes. In Addition, The 3-Flat Shank Prevents Slipping In The Chuck And Also Provides Powerful High-Torque Transmission.Features:- Cnc Ground Spiral Flute Enables Optimised Chip Removal And Less Vibration For Even Drilling- Highest Cutting Smoothness Due To Axial And Radial Relief Grinding- Made Of Hss For A Long Lifetime. Laser-Markings For Hole Diameters.- Made Of Hss For A Long Lifetime. Laser-Markings For Hole Diameters. 3-Flat Shank For High-Torque Transmission, No SlippingSpecifications:- …

Professional Quality, manufactured from chrome vanadium steel hardened, tempered and chrome plated for corrosion protection. Chamfered end allows positive nut location and entry. Hole for driving acce more→ssory with locking pin. Manufactured to DIN 3124/ISO 2725 and DIN 3120/ISO 1174 Specifications Contents: 1 x Elora Bi-Hexagon Socket, 1" Sq. Dr., 50mm

A basic no-nonsense 12 piece 1/2" drive set of sockets with an FRP ratchet and an extension bar. The set is supplied in a clip box which stores the sockets and includes a clip rail facility for adding more→extra sockets. Contents: FRP Ratchet & 5" Extension Bar. Sockets: 8, 10, 12, 13, 14, 15, 17, 18, 19 & 24mm