Submersible (Drainage) Pumps

Ideal for pumping water from flooded areas, cellars, sumps etc. Pumps small soft solids in suspension. Not suitable for ponds or water features. Made from tough engineering plastic and stainless steel. Low energy 150 watt motor has overload protection. Built in handle. 10m of heavy duty H07RNF cable included. Selectable manual or auto mode - auto will turn on at 251mm and off at 81mm and work in confined areas.

Ideal for pumping water from flooded areas, cellars, sumps etc. Pumps small soft solids in suspension. Not suitable for ponds or water features. Made from tough engineering plastic and stainless steel. Low energy 150 watt motor has overload protection. Built in handle. Hose connector included and 10m of heavy duty H07RNF cable. Selectable manual or auto mode - auto will turn on at 251mm and off at 81mm and work in confined areas.

Ideal for pumping water from flooded areas, cellars, sumps etc. Pumps small soft solids in suspension. Not suitable for ponds or water features. Made from tough engineering plastic and stainless steel. Low energy 150 watt motor has overload protection. Built in handle. 10m of heavy duty H07RNF cable included.

Ideal for pumping water from flooded areas, cellars, sumps etc. Pumps small soft solids in suspension. Not suitable for ponds or water features. Made from tough engineering plastic and stainless steel. Low energy 150 Watt motor has overload protection. Built in handle. Hose connector included and 10m of heavy duty H07RNF cable.

This PSV6A Clarke Water Pump is ideal for draining surface water including flooded cellars, sumps etc. Ideal for pumping clean and dirty water and features fold down legs/base to pump water containing solid bodies up to 30mm in diameter or surface water. Adjustable position float switch automatically turns the pump off when water level drops

750W Submersible Pump with integrated float switch. This submersible pump is ideal for heavy duty draining applications including pits, sumps, ditches, footings etc. It can be used to remove both clean and dirty water including particles up to 35mm dia. The integrated float switch will switch off the pump motor once the water level is reduced to a defined level. Being integrated within the pump housing it is usable in a more confined space than would be the case with conventional float switches Note: Suitable for use with clean or dirty water

400W Puddle Pump with Auto sensor - This submersible pump is ideal for draining flooded cellars, sumps etc. This is the perfect solution for clearing shallow bodies of water such as spillages because of its ability to pump as low as 1mm from the floor. Note: Suitable for use with clean water only

High power (750W) efficient submersible water pump with float switch. Benefiting from a big 208 litres per minute output and on/off float switch that can be set to operate or be turned off, for continuous duty. This submersible water pump is perfect for draining and transferring water in many different domestic situations. Examples of use include draining cellars and basements, flooded boats, pits, pools etc. It could also be used with the float switch disabled to drain blocked sinks or baths. Note: Suitable for use with clean water only

Clarke's CSV4A 1300W Submersible pump with float switch is an electric powered water pump that is perfect for draining and transferring water in many different situations, with its massive 417L /min flow and 11m Max. head. Examples of use include draining cellars and basements, ditches, footings etc. Note: Suitable for use with clean water or dirty water.

Ideal for pumping water from flooded areas, cellars, sumps etc. Pumps large soft solids in suspension. Not suitable for ponds or water features. Made from tough engineering plastic and stainless steel. Low energy 150w motor has overload protection. Built in handle. Hose connector included and 10m of heavy duty H07RNF cable. Selectable manual or auto mode - auto will turn on at 285mm and off at 100mm and work in confined areas.

For heavy and continuous duty pumping of water levels down to 1mm, with a rubber moulded electronic level probe switch. Ideal for automatic control of water levels on flat roofs, car-parks, concrete shuttering, lift-shafts, basements and during incidents of flooding. Power saving as will only operate when probes sense water (not run continuously), then operate for 1 minute after level drops below probes, but continue pumping if probes touch water again during this time. Start level depth of water is approximately 170mm, but probe extensions to turn on approximately at depths of 70mm (70mm kit) and about 5mm (170mm kit) are an optional extra. Pumps water with sand and silt in suspension.

For heavy and continuous duty pumping of water levels down to 1mm, with a rubber moulded electronic level probe switch. Ideal for automatic control of water levels on flat roofs, car-parks, concrete shuttering, lift-shafts, basements and during incidents of flooding. Power saving as will only operate when probes sense water (not run continuously), then operate for 1 minute after level drops below probes, but continue pumping if probes touch water again during this time. Start level depth of water is approximately 170mm, but probe extensions to turn on approximately at depths of 70mm (70mm kit) and about 5mm (170mm kit) are an optional extra. Pumps water with sand and silt in suspension. Made

For heavy and continuous duty pumping of water levels down to 1mm, with a rubber moulded electronic level probe switch. Ideal for automatic control of water levels on flat roofs, car-parks, concrete shuttering, lift-shafts, basements and during incidents of flooding. Power saving as will only operate when probes sense water (not run continuously), then operate for 1 minute after level drops below probes, but continue pumping if probes touch water again during this time. Start level depth of water is approximately 170mm, but probe extensions to turn on approximately at depths of 70mm (70mm kit) and about 5mm (170mm kit) are an optional extra. Pumps water with sand and silt in suspension. Made

For heavy and continuous duty pumping of water levels down to 1mm, with a rubber moulded electronic level probe switch. Ideal for automatic control of water levels on flat roofs, car-parks, concrete shuttering, lift-shafts, basements and during incidents of flooding. Power saving as will only operate when probes sense water (not run continuously), then operate for 1 minute after level drops below probes, but continue pumping if probes touch water again during this time. Start level depth of water is approximately 170mm, but probe extensions to turn on approximately at depths of 70mm (70mm kit) and about 5mm (170mm kit) are an optional extra. Pumps water with sand and silt in suspension.

For heavy and continuous duty pumping of water levels down to 1mm. Ideal for draining water on flat roofs, car-parks, concrete shuttering, lift-shafts and basements. For use in tool-hire, on building sites, flood defence and general drainage of building sites, Pumps water with sand and silt in suspension. Can run for long periods while pumping minimal water and in any position. Made from tough steel and rubber. Built in handle. 10m of heavy duty H07RNF cable. Hose connector adjustable to two positions to avoid hose kinking.

For heavy and continuous duty pumping of water levels down to 1mm. Ideal for draining water on flat roofs, car-parks, concrete shuttering, lift-shafts and basements. For use in tool-hire, on building sites, flood defence and general drainage of building sites, Pumps water with sand and silt in suspension. Can run for long periods while pumping minimal water and in any position. Made from tough steel and rubber. Built in handle. 10m of heavy duty H07RNF cable. Hose connector adjustable to two positions to avoid hose kinking.

Ideal for heavy and continuous duty pumping on building sites, ditches, footings, processes etc. Used extensively in tool hire. Pumps water with sand and silt in suspension. Can run for long periods while pumping minimal water and in any position. Made from tough steel and rubber. Built in handle. 10m of heavy duty H07RNF cable. Hose connector adjustable to two positions to avoid hose kinking. Selectable manual or auto mode - turns pump off when water level drops and protect from dry running.

Ideal for heavy and continuous duty pumping on building sites, ditches, footings, processes etc. Used extensively in tool hire. Pumps water with sand and silt in suspension. Can run for long periods while pumping minimal water and in any position. Made from tough steel and rubber. Built in handle. 10m of heavy duty H07RNF cable. Hose connector adjustable to two positions to avoid hose kinking. Selectable manual or auto mode - turns pump off when water level drops and protect from dry running.

Ideal for heavy and continuous duty pumping on building sites, ditches, footings, processes etc. Used extensively in tool hire. Pumps water with sand and silt in suspension. Can run for long periods while pumping minimal water and in any position. Made from tough steel and rubber. Built in handle. 10m of heavy duty H07RNF cable. Hose connector adjustable to two positions to avoid hose kinking.

Ideal for heavy and continuous duty pumping on building sites, ditches, footings, processes etc. Used extensively in tool hire. Pumps water with sand and silt in suspension. Can run for long periods while pumping minimal water and in any position. Made from tough steel and rubber. Built in handle. 10m of heavy duty H07RNF cable. Hose connector adjustable to two positions to avoid hose kinking.

Ideal for heavy and continuous duty pumping on building sites, ditches, footings, processes etc. Used extensively in tool hire. Pumps water with sand and silt in suspension. Can run for long periods while pumping minimal water and in any position. Made from tough steel and rubber. Built in handle. 10m of heavy duty H07RNF cable. Hose connector adjustable to two positions to avoid hose kinking.

Ideal for heavy and continuous duty pumping on building sites, industrial processes, tunneling, mines and quarries. Pump water with sand and silt in suspension. Can run for long periods while pumping minimal water and in any position. Made from heavy duty cast iron, tough steel and ductile iron. Built in handle. 20m of heavy duty H07RNF cable. Supplied with two hose connectors: spigot and mBSP Both adjustable to two positions to avoid hose kinking and supplied as Selectable manual or auto sensor mode - turns pump off when water level drops and protect from dry running.

Ideal for heavy and continuous duty pumping on building sites, industrial processes, tunneling,mines and quarries . Pump water with sand and silt in suspension. Can run for long periods while pumping minimal water and in any position. Made from heavy duty cast iron, tough steel and ductile iron. Built in handle. 20m of heavy duty H07RNF cable. Supplied with two hose connectors: spigot and mBSP Both adjustable to two positions to avoid hose kinking and supplied as Selectable manual or auto sensor mode - turns pump off when water level drops and protect from dry running.

Ideal for heavy and continuous duty pumping on building sites, industrial processes, tunneling,mines and quarries . Pump water with sand and silt in suspension. Can run for long periods while pumping minimal water and in any position. Made from heavy duty cast iron, tough steel and ductile iron. Built in handle. 20m of heavy duty H07RNF cable. Supplied with two hose connectors: spigot and mBSP Both adjustable to two positions to avoid hose kinking and supplied as Selectable manual or auto sensor mode - turns pump off when water level drops and protect from dry running.