Other Hand Tools

This Monument Three-Legged Radiator Valve Key is used for 1/2in, 3/4in and 1in radiator valve's. It has 7, 8 and 9mm square profiles.The key is made from brass pressing.Additional Information:• Type: Key

The Monument 2059M Multi-Purpose Four-Way Key is used for gas, water and electric meter cupboards, air conditioning units, stop valves, mains consoles etc, as well as central heating pump cocks, some radiator and drain off valves.Additional Information:• Type: Key

This Monument 2116N Burrfect® Square Deburrer cleans and deburrs 4 different sizes of plastic waste pipe, it is a high quality metal square with each side de-burring a different size of plastic pipe.This deburrer tool will deburr the following sizes: 19mm (3/4in), 32mm (1.1/4in), 38mm (1.1/2in) and 50mm (2in).The 2116N includes a handy hanging hole, and is made in Britain.Additional Information:• Type: Deburring Tool

The Monument 2580U Vent Sizing Gauge is used to measure the size of the slots in an air vent to calculate the area of ventilation provided by a vent where this info is not readily available. The gauge is stepped in increments of 1mm and will measure vent slots from 5mm up to 10mm. Made from stainless steel.Additional Information:• Type: Vent Guage

The Monument Copper Pipe Bender, 15-22mm, is designed to professionally bend BSEN1057 15mm and 22mm copper pipe and 15mm stainless steel tube. The aluminium formers are marked with bending angles of 30, 45-and 90-degree offsets allowing for accurate bending. The Monument Pipe Bender is supplied with a replaceable 15mm (MON2601) and 22mm (MON2603) aluminium bending guides.The Monument Pipe Bender can also be used with the MON2626 2626M Bending Arm Extension allowing for easier bending of 22mm pipe. Replacement guides, formers and hook stops are available separately. Additional Information:• Type: Mini Bender• Size: 15-22mm

This Monument 2611S Mini Bender is for up to 180° bends on 6, 8 and 10mm copper pipe (outside diameter).Additional Information:• Type: Mini Bender• Size: 6-10mm

Monument pipe cutter wheels are made from high quality, heat treated steels.

Monument Trac Pipe is a stainless steel, bendable corrugated gas pipe with a yellow polyethylene cover.This cutter has been designed to cut the omegaflex Trac Pipe from DN15/15 mm to DN32/32 mm.Additional Information:• Suitable For: Trac Pipe• Capacity: DN15/15mm - DN32/32mm

Monument Compression Fitting Spanner double ended spanner for tightening and loosening most 15 and 22 mm compression fitting nuts. Size: 15/22 mm.Twin Pack of Compression Fitting Spanners 15/22mm.Additional Information:• Size: 15 x 22mm

Monument Radiator Spanners Twin Pack with 1 x 10mm and 1 x 12mm square section radiator spanners. Suitable for vent plugs and bleed screws. They are made from zinc plated steel with a slightly offset handle for ease of use.Additional Information:• Type: Spanner

Monument Semi-Automatic Pipe Cutter enables 8-22 mm diameter copper and thicker walled plastic pipes such as those used in Central heating to be cut automatically once it has been sized and tightened. Thin walled plastic pipes may collapse too easily unless an internal support is given to pipes. After tightening no further adjustment or feeding of the wheel into the tube is required. Soft copper can also be cut without crushing if the tool is used like a conventional Cutter by feeding the wheel into the tube.Ideal for use in confined spaces. Capacity 8 to 22mm. Replacement wheel number MON301.Additional Information:• Suitable For: Copper/Plastic• Capacity: 8-22mm

Monument Disposable deburring tool. The swivelling blade rotates freely to allow allsorts of deburring operations to be carried out inside tubes, on sheet materials, inside holes etc. Suitable for use on steel, copper, brass, plastics, wood and castings.Additional Information:• Type: Deburring Tool

Monument Abrasive Clean Up Strips, 180 grit silicone clean up strips of abrasive waterproof open mesh material for a multitude of cleaning jobs such as roughing up pipe, cleaning inside fittings (can be cut into small strips), deburring metal and wooden surfaces.Additional Information:• Type: Cleaning Tool

Monument Clean & Polish Pads are suitable for cleaning, polishing, rust removal, scrubbing and blending. They are rust proof, washable and will not break up during use. Size: 50 x 250 mm pads, medium grit.Additional Information:• Type: Cleaning Tool

The Monument 3034T Copper Fitting Cleaning Brush has stiff steel bristles for cleaning copper fittings and socket formed joints on copper pipe, prior to soldering. Specifications: Size: 15 & 22mm.Additional Information:• Type: Cleaning Tool

The Monument 331E Crutch End Domestic Stopcock Key has been designed for turning on and off hard-to-reach or difficult stopcocks, such as under kitchen units, sinks and stiff to turn outside taps. The design provides increased leverage and is supplied with a removable tommy bar in hexagon shaft. This allows it to connect to a socket and ratchet handle for ease of use in difficult corners.Additional Information:• Head Type: Crutch• Length: 220mm

Monument Internal / External Pipe End Deburrer is capable of deburring pipes up to 35mm in diameter.Additional Information:• Type: Deburring Tool

The Monument, pack of 3, Boiler Flue Brushes (MON3014J-1), contains the following brush sizes: 16mm diameter, 50mm diameter and 50 x 16mm.Additional Information:• Type: Cleaning Tool

Moument Flux Brushes have wooden handles. Designed for applying flux to facilitate the process of making soldering joints, these brushes can also be used for general-purpose applications. Head Length: 10mm.Total Length: 195mm.Pack Quantity: 5.Additional Information:• Type: Cleaning Tool

This Gasex UN2037 Gas is a professional grade gas from Monument enables 30% faster soldering and brazing than propane.It does not contain butadiene, TUV approved and complies to EN417. Specifications: Thread: 7/16in.Bottle size: 450g.

The Monument 437A Adaptor connects the 430F professional soldering and brazing torch (UNEF 7/16 in) to 1in US-Style bottles e.g., propane, MAPP® and MAPPro®.Made in BritainAdditional Information:• Type: Accessories

This Monument 438D Adaptor Primus 2000 To 430F adaptor adapts the Monument 430F Professional Torch to refillable bottles e.g., Primus®2000 and Calor®340.UNEF: 7/16in.Made in Britain.Additional Information:• Type: Accessories

The Monument 4501F GRIP+ R2 3-Stepped Radiator Valve Tool fits most radiator end caps and valves. The 3-stepped tool has the following sizes: 10mm & 12mm Slotted and 1/2in A/F Hex. Use with MON4537 Shorty Swivel Head Handle or MON345 Pro Adjustable Basin Wrench allowing improved access. Additional Information:• Type: Radiator Valve Tool

The Monument 4507X GRIP+ R1 Radiator Thermostatic Radiator Valve Tail Fitting Tool with 16mm internal hex. Fits most radiator valves. Use with MON4537 Shorty Swivel Head Handle or MON345 Pro Adjustable Basin Wrench allowing improved access. Made in Britain.Additional Information:• Type: TRV Tail Spanner