Other Hand Tools Monument

The Monument 1010 are manufactured from a single piece of malleable iron for greater durability and strength, with a tee handle for greater torque...

Monument 173 has been especially designed for removing stiff backnuts from awkward placed taps and to make tap installation a more rapid process this tool is for 1/2-inch. BSP and 3/4-inch. BSP taps. The Monument 170 tool stays in position on the tap tail so can be used with one hand and uses mechanical advantage of the thread of the tap tail to remove stiff nuts. Ideal for 1/2-inch and 3/4-inch BSP 25 mm 27 mm nuts 29 mm ribbed 32 mm nuts. The MON173 is complete with 3/8-inch cordless drill adaptor 1/2-inch square drive extension tube and full user instructions. For removing stiff backnuts and rapid tap installation for 1/2-inCH. BSP and 3/4-inch. BSP Taps.Tool stays in position on the …

The Monument AC4P Autocut® Plastic Pipe Cutter has an easy-to-use design simply clip on and rotate to cut. It will only cut the exact size of the plastic pipe specified. Designed and manufactured in Britain.This Monument AC4P Autocut® Plastic Pipe Cutter is suitable for 10mm plastic plumbing pipe.PTDMON110

The Monument AC4P Autocut® Plastic Waste Pipe Cutter is suitable for cutting Push Fit and Solvent Weld waste pipe. It has an easy-to-use design simply clip on and rotate to cut. It will only cut the exact size of the plastic pipe specified. Designed and manufactured in Britain.This Monument AC4P Autocut® Plastic Waste Pipe Cutter is suitable for 1.1/2in Push Fit and Solvent Weld waste pipe. Whilst nominally called 1.1/2in pipe the Push Fit and Solvent Weld pipe actual sizes vary from 37mm I.D. inner diameter to 43mm O.D. outer diameter.PTDMON1112

The Monument AC4P Autocut® Plastic Waste Pipe Cutter is suitable for cutting Push Fit and Solvent Weld waste pipe. It has an easy-to-use design simply clip on and rotate to cut. It will only cut the exact size of the plastic pipe specified. Designed and manufactured in Britain.This Monument AC4P Autocut® Plastic Waste Pipe Cutter is suitable for 2in Push Fit and Solvent Weld waste pipe. Whilst nominally called 2in pipe the Push Fit and Solvent Weld pipe actual sizes vary from 50mm I.D. inner diameter to 56mm O.D. outer diameter.PTDMON1200

This Monument 1277s is a replacement hose to fit gas test gauges. It has an internal diameter of 7/32 in (5.5mm). They are black nitrile for standard and are 1m in length (Coil). NOTE: Do not use this hose for LPG (low pressure gas).PTDMON1277S

Monument 1279 Black replacement hose to fit gas test gauges are 1m in length and have an internal diameter of 7/32 in (5.5mm). Note: Do not use this hose for LPG (Liquified Petroleum Gas).PTDMON1279

These Monument socket forming tools (Copper pipe jointers) are ideal for joining two pieces of Copper pipe of equal diameter together without using fittings. The loose former allows easier withdrawal of tool after use. The resulting capillary jointthat is left can be soft or hard soldered to finish the joint.

The Monument MON1368 1368U 2 Piece Test Plug Set is used for blocking off small pipes such as copper pipes for dry testing prior to commissioning. They cannot be used for air testing purposes by themselves. 2 Plugs supplied: 1 x 1370B 15mm Test Plug. 1 x 1371E 22mm Test Plug.PTDMON1368

This Monument set of 6 Test Plugs contains the following small bore test plugs: 2 x 1370B 15mm Test Plugs.2 x 1371E 22mm Test Plugs.2 x 1372H 28mm Test Plugs. The plugs are used for blocking off small pipes such as copper pipes for dry testing prior to commissioning however they cannot be used for air testing purposes by themselves.PTDMON1369

Monument Drain Testing Plugs are durable quality flexible drain plug for the plugging of drains and pipes. This plug is easy to use and are available in various sizes. Fitted with removable top caps and rubber rings. These plugs are easy to use just place in the pipe end that is being repaired or replaced and simply turn the wing nut knob this will depress the rubber cone this will make it expand to seal pipe or tube end with a water tight seal.Diameter range: 48-62mm. Maximum allowable back pressure: 37psi (2.50bar).1/2 in BSP outlet.PTDMON1376

Monument socket forming tools (copper pipe jointers) are ideal for joining 2 pieces of copper pipe of equal diameter together without using fittings. The loose former allows easier withdrawal of tool after use. The resulting capillary joint that is left can be soft or hard soldered to finish the joint. Available in a variety of sizes: 15 22 28 and 15 & 22mm.This Monument 138R Copper Pipe Jointer has the following specification: Pipe Diameters: 15mm and 22mmPipe Thickness: 0.7mm and 0.9mmPTDMON138

The Monument MON1445 1445F spare hose for connecting testing equipment comes in the following: Length: 1m.Internal Diameter: 10mm.PTDMON1445

The Monument Hydro-jet Pump safely provides the explosive power of a water jet to unblock sinks baths showers toilets and drains. First you fill the unit with water then hold the unit over the waste and pump down (or hit) the handle to create a powerful water jet to help clear any blockage. To clean the MON1452 simply just flush with clean water. Comes with 3 adaptors for sinks drains and toilets. Size: 35cm x 7cm x 7cm. PTDMON1452

Monument 1453e Suction Plunger 5.1/2in Ideal for clearing WC pan wastes Gullies with soft flexible rubber Wooden tee handle Monument 1453E...

Monument force cups or plungers are used to remove blockages from bath and sink waste pipes by building up the air pressure.1 x Monument 1456N Small Force Cup Plunger 75mm (3in)PTDMON1456

Monument master plunger Newly designed plastic Master Plunger. To remove blockages from bath and sink waste pipes by building up pressure. 125mm Face.

Item Package Quantity: 1 Monument master plunger Newly designed plastic Master Plunger. To remove blockages from bath and sink waste pipes by...

The Monument 1470F Smoke Emitter Pellets are professional-grade smoke testing pellets designed for flue, chimney and ventilation system testing applications. These smoke pellets produce a dense white, low-toxic smoke when ignited, making them ideal for identifying leaks, blockages and airflow issues in heating and ventilation systems. Each pellet delivers approximately 15m³ of smoke with a consistent 60-second burn time, providing sufficient volume and duration for thorough testing of domestic and light commercial installations. Supplied in a convenient pack of 10 pellets, the Monument 1470F offers reliable performance for heating engineers, gas fitters and building services contractors conducting r…

The Monument 1515U Water Flow Weir Gauge is designed to measure water flow rates in order to determine if suitable flow is available in a building prior to the plumbing installation of washing machines boilers showers etc. This type of water flow gauge is also used for diagnosing if a combi boiler or water heater may need de-scaling. The water flow gauge is made from durable plastic with a stainless steel mesh strainer to avoid turbulence. It features a dual scale to measure flow rates of 2 to 25 litres and 1 to 5 gallons per minute.PTDMON1515

The All New 2030B-1 Are 15mm Single Sized Olive Cutters Designed And Made By Monument Tools. Simply Slide The Olive Cutter Onto The End Of The Pipe.

This Monument spare rubber hose is for use with U gauges. They have a coil length of 2m and an internal diameter of 7/32in (5.5mm). Specifications: Colour: Black.Length: 2m (78in) (coil). PTDMON1729

The Monument 1730X Orange Hose for Gas Test Gauges. Rubber Hose ID: 5.5mm food quality Length: 2m. Colour: OrangePTDMON1730

Test Nipples screw into gas meters to enable connection to a gas test gauge. The hexagon screw shuts off supply to the gauge.1/8in. BSP thread.PTDMON1732