Microphones

Microphone cartridge holder of rubber, for the protection and correct insertion of electret microphone cartridges. Suitable for cartridges with a diameter of 9.7mm.

 Microphone Thread Adaptor Adaptor to convert 3/8'' thread to 5/8'' thread.

High-quality electret microphone cartridge (omnidirectional characteristic), for PCB mounting, pin spacing 2.5. Frequency range 50-16,000Hz Sensitivity 7.9mV/Pa/1kHz, 3dB Output impedance 2.2k ohm S/N ratio > 58dB Coupling capacitor 0.1-4.7F Admiss. ambient temp. 0-40 C Power supply 1.5-10V DC current /0.5mA

A holder to accommodate microphones of a diameter between 26 - 30mm, with adjustable tilt and 5/8" thread at the base. Thread at base: 5/8" UNS Microphone diameter: 26 - 30mmØ Weight: 38g

High-quality subminiature back electret microphone cartridge for standard microphones (omnidirectional characteristic), small sized housing. Technical Specification Frequency range 20-16,000Hz Sensitivity 6.3mV/Pa/1kHz/3dB Output impedance 2.2kΩ S/N ratio > 58dB Coupling capacitor 0.1-4.7F Admiss. ambient temp. 0-40 C Power supply 1.5-10V DC current /0.5mA

Its time to clean up your vocal sound. The LD Systems Vocal Microphone Windscreen helps you achieve clean vocals by eliminating unwanted pops clicks and wind noise. The Windscreen also aids stage management as it is available in black blue orange yellow and red making colour coding your microphones a simple task. The LD Systems Microphone Windshield is very versatile and can be used with any standard sized dynamic vocal mic with a diameter of 40 - 50 mm.

The Behringer MC2000 Microphone Clamp fits any microphone with a diameter between 24mm to 35mm. It is a must-have accessory for any performer singer or public speaker. Its plastic construction makes the MC2000 almost break-resistant while its adjustable swivel allows you to find the perfect angle. In addition the MC2000 also comes complete with a 3/8" to 5/8" mic stand adapter. Please note: does not come with a microphone

Black foam windshield. Colour - Black Dimensions (mm) - 40 x 40 x 60 mm Diameter (mm) - 22

Microphone windshield of black foam. For microphones with Ø 11-15mm Dimensions: Ø 30mm x 51mm Suitable e.g. for ECM-200, PAM-10

The Gravity MSQC Quick Coupler Crown For Mic Clips allows engineers to get increased value out of their MSQC Quick Couplers. The spare crowns are perfect for studios with more mic clips than stands as they will allow many mics to be ready to mount on stands with Quick Couplers. The two-piece coupler features a 5/8" female thread that attaches to the mic stand and a 3/8" male thread that attaches to mic clips and boom arm hubs. The Spare Crown is the section to attach to mic clips.

High-quality electret microphone cartridge (omnidirectional characteristic), with 150mm shielded cable and insulated, tin-plated cable ends. An external 1-2.2k ohm resistor is required for AF decoupling. Technical Specification Frequency range 50-16,000Hz Sensitivity 7.9mV/Pa/1kHz, 3dB Output impedance 2.2kohm S/N ratio > 58dB Coupling capacitor 0.1-4.7F Admiss. ambient temp. 0-40 C Power supply 1.5-10V DC current /0.5mA

Microphone clamp with 5/8" and 3/8" thread for connection to a stand. - Colour: Black - Material: ABS - Holder Type: Clamp - Holder diameter: Under 44 mm - Screw thread size: 3/8 " & 5/8 "

Suitable for most handheld microphones

Microphone Clip by Gear4music is a generic mic clip for attaching microphones to microphone stands. The clip features a 5/8" thread size and is suitable for a wide range of microphones.

The Wireless Microphone Clip by Gear4music is a wide bodied clip suitable for use with a wide range of handheld wireless mics. The clip attaches to a mic stand with a 5/8" thread. Please Note: This clip is suitable for microphones with a circumference of 9-11cm at the base.

Microphone windshield, of black foam. General Information: For microphones with Ø 7-9mm Dimensions: Ø 14mm x 15mm Suitable e.g. for ECM-300L

The Stagg MH-12AH Mic Clip is a flexible practically unbreakable and ROHS compliant nylon microphone clamp with a 5/8" mounting brass thread and 5/8"(out) to 3/8"(in) thread adaptor. Finished in black the MH-12AH is suitable for tapered microphones.

This is a Stagg Microphone Clip designed for mics of diameter 32 to 42 mm / 1.25 to 1.65 inch. Includes 5/8"(out) to 3/8"(in) thread adapter.

Its time to clean up your vocal sound. The LD Systems Conference Microphone Windscreen helps you achieve clean speech sound by eliminating unwanted pops clicks and wind noise. The Conference Mic Windshield is compatible with a range of conference and lapel microphones with a diameter of 7 - 12 mm. The Conference Microphone Windshield helps to give you a professional clean sound at any event.