Chargers & Jump Starters

• Cable & Clamp Length: 0.6m.• Delivers up to 1200 Peak Amps of initial starting power.• Composite case with integral battery clamp storage and carry handle.• Suitable for starting vehicles with 6-cylinder petrol engines up to 3.5L and 4-cylinder diesel engines up to 3L.• Front panel displays internal battery charge level and includes an integral LED work light.• Reverse polarity and short circuit protection with audible warning.• Mains charger with automatic power cut-off prevents damage to battery whilst charging.• Inbuilt MOSFET circuit protection.• Fitted with two 12V power sockets that will accept any 12V device with a vehicle accessory socket plug.• Single 5V 2.4A USB output.• Supplied wi…

• Heavy-duty steel case, high power US manufactured battery and industrial quality switchgear make this model suitable for starting most vehicles.• Positive action power switch reduces risk of inadvertent damage by over-voltage.• Heavy-duty 2m x 35mm² copper cables provide efficient power transfer.• Twin trips prevent damage to battery or internal circuitry.• Easy-to-read LED battery indicator to IEC 51 provides fast indication of battery’s state of charge.• Surge and spike suppressing circuitry reduces risk of damaging vehicle’s on-board electronics.• Fitted with charge balance circuitry to provide even charge to integral batteries.• Supplied with mains voltage recharge unit.• Made in Europ…

• Housed in a tough composite case, this unit is designed to prevent damaging voltage spikes and surges reaching delicate vehicle electronics.• Clips across the battery terminals and permits processes such as welding and plasma cutting to be carried out without the danger of damaging the vehicle’s on board electronics.• Fitting recommended before any routine workshop maintenance.• Shows green light when operating correctly and red light for fault.• Fitted with heavy-duty, fully insulated battery clips.Housed in tough composite case, this unit is designed to prevent damaging voltage spikes and surges reaching delicate vehicle electronics. Clips across the battery terminals and permits processes su…

• Housed in a tough composite case, this unit is designed to prevent damaging voltage spikes and surges reaching delicate vehicle electronics.• Clips across the battery terminals and permits processes such as welding and plasma cutting to be carried out without the danger of damaging the vehicle’s on board electronics.• Fitting recommended before any routine workshop maintenance.• Shows green light when operating correctly and red light for fault.• Fitted with heavy-duty, fully insulated battery clips.Housed in tough composite case, this unit is designed to prevent damaging voltage spikes and surges reaching delicate vehicle electronics. Clips across the battery terminals and permits processes su…

• Heavy-duty steel case, high power US manufactured battery and industrial quality switchgear make this model suitable for starting most vehicles.• Positive action power switch reduces risk of inadvertent damage by over-voltage.• Heavy-duty 2m x 35mm² copper cables provide efficient power transfer.• Twin trips prevent damage to battery or internal circuitry.• Easy-to-read LED battery indicator to IEC 51 provides fast indication of battery’s state of charge.• Surge and spike suppressing circuitry reduces risk of damaging vehicle’s on-board electronics.• Fitted with charge balance circuitry to provide even charge to integral batteries.• Supplied with mains voltage recharge unit.• Made in Europ…

• Heavy-duty steel case, high power US manufactured battery and industrial quality switchgear make this model suitable for starting most vehicles.• Positive action power switch reduces risk of inadvertent damage by over-voltage.• Heavy-duty 2m x 35mm² copper cables provide efficient power transfer.• Twin trips prevent damage to battery or internal circuitry.• Easy-to-read LED battery indicator to IEC 51 provides fast indication of battery’s state of charge.• Surge and spike suppressing circuitry reduces risk of damaging vehicle’s on-board electronics.• Fitted with charge balance circuitry to provide even charge to integral batteries.• Supplied with mains voltage recharge unit.• Made in Europ…

• Professional grade, high performance AGM battery, specially formulated to jump-start vehicles.• DEKRA approved emergency jump starter.• Includes an automatic maintenance charger with patented microprocessor controlled speed charging and thermal runaway protection.• Unlike other booster packs, this unit can be left safely on charge continuously.• Audible warning system (AWS) signals if the unit has been turned on for too long without being connected to a battery and reverse polarity.• Fitted with an isolating rotary on/off switch and features a digital display showing the internal battery level and the vehicle battery voltage.• Fitted with a 12V accessory socket and a single 2.1A USB port id…

• Professional grade, high performance AGM battery, specially formulated to jump start vehicles.• DEKRA approved emergency jump starter.• Includes an automatic maintenance charger with patented microprocessor controlled speed charging and thermal runaway protection.• Unlike other booster packs, this unit can be left safely on charge continuously.• Audible warning system (AWS) signals if the unit has been turned on for too long without being connected to a battery and reverse polarity.• Fitted with an isolating rotary on/off switch and features a digital display showing the internal battery level and the vehicle battery voltage.• Fitted with a 12V accessory socket and a single 2.1A USB port id…

• Cable & Clamp Length: 0.6m.• 22Ah Professional grade, high output AGM battery especially formulated to jump start vehicles.• Fully sealed battery enables the unit to be stored in any position.• Features a lightweight, high-impact casing, which is durable and corrosion proof for easy portability.• Battery status LEDs indicate to the user when the battery is at full power, 75% charge, 50% charge or less and when the unit needs to be recharged.• A fusible link integrated in the output cable gives increased protection to the unit, while enabling fuse change without disassembly.• On/off switch for safety and control.• Features 12V accessory outlet including overload and short circuit protection.• Wei…

• Compact 6/12V quad bank battery charger perfect for automotive, motorcycle and marine workshops.• Suitable for charging a variety of batteries, charger reacts continuously to battery condition and delivers whatever charge rate is required.• Four bank charger outputting 4 x 2A depending on the condition and charge of each battery.• Constantly regulated voltage patterns allow the battery to be recharged fully and safely without fear of overcharging.• Compatible with all AGM, Gel and VRLA flooded batteries commonly found in everything from automotive and farm equipment to motorcycles, ATVs, golf buggies and lawnmowers.• Supplied with SAE “quick” connectors on leads and battery terminals eyelet…

• Compact 6/12V dual bank battery charger perfect for automotive, motorcycle and marine workshops.• Suitable for charging a variety of batteries, charger reacts continuously to battery condition and delivers whatever charge rate is required.• Two bank charger outputting 2 x 5A depending on the condition and charge of each battery.• Constantly regulated voltage patterns allow the battery to be recharged fully and safely without fear of overcharging.• Compatible with all AGM, Gel and VRLA flooded batteries commonly found in everything from automotive and farm equipment to motorcycles, ATVs, golf buggies and lawnmowers.• Supplied with SAE “quick” connectors on leads and battery terminals eyelet…

1. Mounting locationWarning! For safety purposes, the product should be installed in a heat-resistant environment. Avoid the presence of e.g. chemicals, synthetic components, curtains or other textiles in the immediate vicinity of the product.
1.1. Install the galvanic isolator in a well ventilated area.1.2. Keep a clear space of 10 cm around the product for ventilation.1.3. The galvanic isolator must be mounted with its length vertical to allow for maximum cooling. Under normal circumstances, the temperature increase of the heat sink is not more than 20 °C. However the unit may become hot when conducting fault ground current.
2. InstallationWarning! The galvanic isolator must be wired …

1. Mounting locationWarning! For safety purposes, the product should be installed in a heat-resistant environment. Avoid the presence of e.g. chemicals, synthetic components, curtains or other textiles in the immediate vicinity of the product.
1.1. Install the galvanic isolator in a well ventilated area.1.2. Keep a clear space of 10 cm around the product for ventilation.1.3. The galvanic isolator must be mounted with its length vertical to allow for maximum cooling. Under normal circumstances, the temperature increase of the heat sink is not more than 20 °C. However the unit may become hot when conducting fault ground current.
2. InstallationWarning! The galvanic isolator must be wired …

• Portable Mode-2 charger is fitted with BS approved 13A plug so it can be used with any standard 13A socket.• Delay timing function enables users to program delayed start time to benefit from off peak electricity tariffs.• The intuitive LED offers users fault codes, charging time, power and temperature displays.• Current: 10A Fixed.• Voltage: 230V 1ph.• UK 3-pin (BS1363) Plug.• Cable length: 5m.• Cable Specification: EN50620 - 3*2.5mm²+2*0.5mm².• Use with an RCD protected power supply.• Supplied with storage case.Portable Mode-2 charger is fitted with BS approved 13A plug so it can be used with any standard 13A socket. Delay timing function enables users to program delayed start time t…

• Portable Mode-2 charger is fitted with BS approved 13A plug so it can be used with any standard 13A socket.• Delay timing function enables users to program delayed start time to benefit from off-peak electricity tariffs.• The intuitive LED offers users fault codes, charging time, power and temperature displays.• Voltage: 230V 1ph.• UK 3-pin (BS1363) Plug.• Cable Length: 5m.• Cable Specification: EN 50620 - 3*2.5mm²+2*0.5mm².• Use with an RCD protected power supply.• Supplied with storage case.Portable Mode-2 charger is fitted with BS approved 13A plug so it can be used with any standard 13A socket. Delay timing function enables users to program delayed start time to benefit from of…

• The Mode-3 charging cable simply plugs into any public or home EV charging point.• Current: 32A.• Voltage: 230V 1ph.• Cable Length: 5m.• Cable Specification: EN50620 - 3*6mm²+2*0.5mm².• IP54 Rated.• Supplied with storage case.The Mode-3 charging cable simply plugs into any public or home EV charging point. Supplied with storage case.• The mode 3 charging cable simply plugs into any public or home EV charging point. • Current: 32A. • Voltage: 230V 1ph. • Cable Length: 5m. • Cable Specification: EN50620 - 3*6mm²+2*0.5mm². • IP54 Rated. • Supplied with storage case. • Model No. EVCC2232Technical Specification:Length: 5mNett Weight: 2.5kgPlug Type: Type 2 to Type 2Current: 32AVo…

• The Mode-3 charging cable simply plugs into any public or home EV charging point.• Current: 32A.• Voltage: 380-450V 3ph.• Cable Length: 5m.• Cable Specification: EN50620 - 5*6mm²+2*0.5mm².• IP54 Rated.• Supplied with storage case.The Mode-3 charging cable simply plugs into any public or home EV charging point. Supplied with storage case.• The mode 3 charging cable simply plugs into any public or home EV charging point. • Current: 32A. • Voltage: 380-450V 3ph. • Cable Length: 5m. • Cable Specification: EN50620 - 5*6mm²+2*0.5mm². • IP54 Rated. • Supplied with storage case. • Model No. EVCC22323Technical Specification:Length: 5mNett Weight: 3.5kgPlug Type: Type 2 to Type 2…

• The Mode-3 charging cable simply plugs into any public or home EV charging point.• Current: 16A.• Voltage: 230V 1ph.• Cable Length: 5m.• Cable Specification: EN50620 - 3*2.5mm²+2*0.5mm².• IP54 Rated.• Supplied with storage case.The Mode-3 charging cable simply plugs into any public or home EV charging point. Supplied with storage case.• The mode 3 charging cable simply plugs into any public or home EV charging point. • Current: 16A. • Voltage: 230V 1ph. • Cable Length: 5m. • Cable Specification: EN50620 - 3*2.5mm²+2*0.5mm². • IP54 Rated. • Supplied with storage case. • Model No. EVCC2216Technical Specification:Length: 5mNett Weight: 2.4kgPlug Type: Type 2 to Type 2Current:…

• The Mode-3 charging cable simply plugs into any public or home EV charging point.• Current: 32A.• Voltage: 230V 1ph.• Cable Length: 5m.• Cable Specification: EN50620 - 3*6mm²+2*0.5mm².• IP54 Rated.• Supplied with storage case.The Mode-3 charging cable simply plugs into any public or home EV charging point. Supplied with storage case.• The mode 3 charging cable simply plugs into any public or home EV charging point. • Current: 32A. • Voltage: 230V 1ph. • Cable Length: 5m. • Cable Specification: EN50620 - 3*6mm²+2*0.5mm². • IP54 Rated. • Supplied with storage case. • Model No. EVCC1232Technical Specification:Length: 5mNett Weight: 2.5kgPlug Type: Type 1 to Type 2Current: 32AVo…

• The Mode-3 charging cable simply plugs into any public or home EV charging point.• Current: 16A.• Voltage: 230V 1ph.• Cable Length: 5m.• Cable Specification: EN 50620 - 3*2.5mm²+2*0.5mm².• IP54 Rated.• Supplied with storage case.The Mode-3 charging cable simply plugs into any public or home EV charging point. Supplied with storage case.• The mode 3 charging cable simply plugs into any public or home EV charging point. • Current: 16A. • Voltage: 230V 1ph. • Cable Length: 5m. • Cable Specification: EN 50620 - 3*2.5mm²+2*0.5mm². • IP54 Rated. • Supplied with storage case. • Model No. EVCC1216Technical Specification:Length: 5mNett Weight: 2.4kgPlug Type: Type 1 to Type 2Current:…

Sealey E/START800 Electrostart Batteryless Power Start is ideal for the professional mechanic and DIY users   The Sealey E/START800 Electrostart Batteryless Power Start is compact and lightweight for easy handling and storage, yet still delivers the same result as heavy, bulky, lead-acid battery equivalents. It is simple and safe to use with no long term battery storage issues and can be fully energised in approximately 2 minutes. Features:  
- Ideal for the professional mechanic and DIY users  
- Can be fully energised in approximately 2 minutes
- Simple and safe to use with no long term battery storage issues 
- Innovative technology with no internal battery so no need to wait hours f…

The Sealey E/START1600 Electrostart Batteryless Power Start can be fully energised in approximately 3 minutes The Sealey E/START1600 is a simple to use batteryless power start. Innovative technology with no internal battery so no need to wait hours for the unit to charge before use. It is compact and lightweight for easy handling and storage, yet still delivers the same result as heavy, bulky, lead-acid battery equivalents. Its digital display indicates battery voltage, capacitor charge and faults. Features:
- Ideal for the professional mechanic and DIY users
- Can be fully energised in approximately 3 minutes
- Simple and safe to use with no long term battery storage issues
- Digital …

• Suitable for 12V & 24V electrical systems. • Fully electronic, microprocessor controlled.• Suitable for EFB & AGM/GEL (stop/start), Lead Acid, Lead Calcium & Silver Calcium batteries.• Battery Range: 4-700Ah.• Up to 10 analysis and charge phases, including trickle/maintenance.• Stabilised charging current allows improved charging efficiency and reduced charging times using ECS (Electronic Control Systems) technology.• Surge and spike protection during charging and starting.• BSU mode provides support for the battery during prolonged electronic diagnostic checks.• Includes wired remote control switch to allow operator to deliver required starting power, while being sat in the connected vehi…

• Suitable for 12V & 24V electrical systems. • Fully electronic, microprocessor controlled.• Suitable for EFB & AGM/GEL (stop/start), Lead Acid, Lead Calcium & Silver Calcium batteries.• Battery Range: 4-550Ah.• Up to 10 analysis and charge phases, including trickle/maintenance.• Stabilised charging current allows improved charging efficiency and reduced charging times using ECS (Electronic Control Systems) technology.• Surge and spike protection during charging and starting.• BSU mode provides support for the battery during prolonged electronic diagnostic checks.Fully electronic, microprocessor controlled battery starter/charger designed to meet the requirements of modern battery technology. Suit…