Car Service Station Equipment

Enables the crank to be held whilst doing up the centre pulley nut which is very tight. Remove 4 pulley mounting bolts then bolt the tool on using the original bolts with the roll pin slot lined up with the roll pin, held with 1/2"D bar. Crankshaft pulley holding tool.For use on Volvo: S40, V40, V50, XC90, XC70, S70, V70, S60, S80, C30, C70. Equivalent to OEM 303-1179. Made in Sheffield.

Oil Filter Wrench / Tool Steel

Brake Tool / Chrome Vanadium Steel

A shorter version of the Laser 4369 that covers some BMW, Land Rover, Rover and GM models. Two sleeves are supplied to increase the application list. The BMW application allows the removal of the sprocket from the shaft when removing the injection pump VP44 and HP CR Pump. Used without centring ring for VP Pumps and with Common rail pumps. This kit has a shorter puller body to fit transverse engines The applications for Vauxhall/Opel/Land Rover and Rover is specifically for transverse mounted engines where space is at a premium.Use with or without ring dependent on applicationSuitable for models 3 Series E46, 5 series E39, 7 Series E38, X5 3.0d also GM Omega-B plus Land Rover Freelander and …

Wheel Wrench / Tool Steel

Designed to allow the removal of valve springs and valve stem oil seals with the cylinder head in place. Combustion chamber is pressurised via the supplied spark plug air line adaptor which holds the valve in place during the valve spring compression operation. Fast set up time due to the twin rail pivot system. Single handed operation.For universal use on SOHC and DOHC engines.For the removal of valve stem oil seals valve springs with the cylinder head in place.Includes a compressed air adaptor (22mm) to hold the valves closed while the springs are in place.Fast set up time due to the twin rail pivot system.Single handed operation. Airline adaptor has 18mm/14mm (male) threaded end to fit spark …

Return fuel volume tester for common rail diesel injectors and conventional injectorsFor up to 10 cylinders.40 Adaptors for Bosch CRD | Siemens CRD | Denso CRD | Delphi CRD.10 graduated fuel chambers.Easy to read fuel chambers.Essential tool.

Most modern systems are either self-bleeding or have a hand pump permanently fitted to the vehicle, however many can still take some time to purge the system of any air. With two basic types of fuel delivery used on modern diesel engines - pressure fed (using an electric fuel pump mounted in the tank to push the fuel up to the high pressure pump) and vacuum fed (using an engine-driven lift pump to generate a vacuum that pulls the fuel up to the high pressure pump) this kit has been developed to allow the user to connect into as many diesel fuel systems as possible using the correct style connector. Features and Benefit For bleeding or priming diesel systems For connection in-line with the …

Brake Tool / Tool Steel

Oil Filter Wrench / Tool Steel

A professional exhaust pipe cutter suitable for standard exhausts and for stainless steel when used with the HSS bladeSupplied with SK2 blades for mild steel exhaust pipesReplacement HSS chain cutters for cutting semi stainless exhaust pipes are available (Part No 5414)Professional quality productReplacement SK2 blades Part No 5413Time saver

Tyre Inflator / Tool Steel

Tyre Pressure Gauge / Sheet Metal

A specialised tool, used to assist the extraction of the copper washers used to seal diesel injectors where they enter the cylinder head.No moving parts to drop into the engineRemoves seals with easeSlide hammer assists in extractionTip diameter: 4.5mm minimum to 13.2mm maximumMade in Sheffield

Designed for the repair of damaged Lambda (oxygen) sensors threads. Set includes: 5 x thread repair inserts M18 x 1.5.M18 x 1.5 taper tap & M20 x 1.5 taper tap. Reamer & insert tool. Spares insert nuts available, please see Laser Part No. 0069 (pack of 5).

Engine valve spring removal kit, can be used with the cylinder head in place if compressed air is used to keep the valves shut (additional components required). Multi fit valve spring compressor Complete with 4 valve adaptor sizes - 34, 26, 20, and 18mm covering most modern multivalve engines. Supplied with two brackets Can be used in situ with head on for valve spring replacement Quick and easy to use

CO2 leak detector fluid for use with 5524 and similar productsCO2 test liquidChanges colour on contact with CO2For use with Laser product 5524 and similar productsROHS certificatedConsumable

Engine timing kit for GM derived belt driven engine 16v 1.6 and 1.8 Z and A engine codes found in Vauxhalls, Chevrolet's, Fiats and Alfa Romeo's.2003 - 2012. Engine timing tool kit for GM engines fitted to Vauxhall/Opel and other vehicles 16v 1.6 and 1.8Applications: Astra-G |H | Corsa-D | Insignia | Mervia | Signum | Vectra-C | Zafira-B 2003-2011Also fits Chevrolet Cruze, Orlando 1.4 | 1.6 | 1.8 and Fiat Croma, Alfa Romeo 159 with 939A4.000 enginesInstructions included Made in Sheffield

For the belt driven 1.4 8 v and 16v PSA engines. KFW engines require the addition of Valve Spring Compressor Laser Number 3789, available separately. Applications 1.4 belt driven PSA engines 16v and 8v petrol ET3 engines Also fits 106 1.1 2001 TU1JP (HFX) Includes: Camshaft locking Pin C089, Camshaft/Crankshaft Locking Pin C101, M10 x 70mm Locking Pin C039, 6mm locking pin C038, flywheel locking pin with long angled shaft for access C560 and timing belt retaining clip C121Supplied with instructionsApplication list includedMade in Sheffield

Quantity 37 Piece

A comprehensive cooling system pressure testing kit for universal use.24 pieces including 16 individually sized adaptors, pressure testing pump with gauge, 2 pressure cap test connectors for use with No 3 adaptor and handle.Suitable for a large range of vehicles including Ford Transit (12/15/21)Thermometer included.Also checks the leakage on original radiator cap.Application list and instructions included. Pump with hose available as replacement - Part No: 1735

Cooling System Pressure Tester for light commercials and HGVPart of the HGV range of toolsSuitable for Mercedes-Benz Sprinter/Volvo/Man/Renault/Daf/Iveco/Erf/ScaniaIncludes pressure pump with gaugeTime saverPacked in eva foam in a blow case

This kit sets the valve timing on the DW10 and DW12 Diesel Fiat and PSA ranges. The DW10 engine range has a 2.0 capacity (1999-) and has SOHC and DOHC The twin cam systems has one camshaft driven by the cam belt and the other shaft driven by a chain in the head. The DW12 range is 2.2 (2001-) A pulley holding tool (3661) may be required to change the chain Made in Sheffield

Engine Timing Tool Ki t- Fiat /Alfa Romeo/Lancia with 1.2/1.4 enginesUpgraded replacement kit for Laser 3788Engine sizes 1.2 and 1.4 Additional pulley holding tools may be required for 1.2 engines Applications: Alfa Romeo Giulietta/MiTo Fiat/500/Brava/Bravo/Grande Punto/Marea/Marea Weekend/Marengo/Palio Weekend Panda/Punto/Punto Classic/Ritmo/Stilo/Idea Lancia Delta/Musa/YpsilonPacked in EVA foam and metal case Made in Sheffield